MM24TGN67.000 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> oscillator> MM24TGN67.000

MM24TGN67.000: DescriptionOscillator, 50MHz Min, 67MHz Max, 67MHz Nom; CategoryPassive components oscillator; File Size87KB，1 Pages; ManufacturerMtronPTI; Websitehttp://www.mtronpti.com; Environmental Compliance

Download Datasheet Parametric Compare View All

MM24TGN67.000 Overview

Oscillator, 50MHz Min, 67MHz Max, 67MHz Nom

MM24TGN67.000 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	102381417
package instruction	DILCC4,.24,200
Reach Compliance Code	unknown
JESD-609 code	e4
Installation features	SURFACE MOUNT
Number of terminals	4
Maximum operating frequency	67 MHz
Minimum operating frequency	50 MHz
Nominal operating frequency	67 MHz
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Package body material	CERAMIC
Encapsulate equivalent code	DILCC4,.24,200
power supply	5 V
Certification status	Not Qualified
Maximum slew rate	60 mA
Nominal supply voltage	5 V
surface mount	YES
Terminal surface	Nickel/Gold (Ni/Au)

Preview

Download Datasheet

View All

MM Series 5.0 X 7.0 X 2.0 mm HCMOS/TTL

Compatible Miniature Surface Mount Oscillators

High Performance HCMOS/TTL

Compatible Surface Mount Oscillators

M-tron MM series quartz crystal oscillators offer

HCMOS technology and an AT-strip crystal in a

miniature ceramic surface mount package.

Output is TTL and HCMOS compatible. Tri-state

output is optional.

Electrical Specifications

Pin Connections

Because this product is based on AT-strip technology, not all frequencies in the range stated are available.

Contact the factory for availability of specific frequencies.

TTL load - See load circuit diagram #1 on page 137. HCMOS load - See load circuit diagram #2 on page 137.

Symmetry is measured at 1.4 V with TTL load, and at 50% Vdd with HCMOS load.

Rise/Fall times are measured between 0.5 V and 2.4 V with TTL load, and between 10% Vdd and 90% Vdd with HCMOS load.

See page 136, Figure 1 for suggested solder profile.

Tri-state Control Logic

Pin 1 high or floating: clock signal output.

Pin 1 low: output disabled to high impedance.

NOTE:

A capacitor of value 0.01

or greater between Vdd

and Ground is recommended.

MM24TGN67.000 Related Products


Description

Recommended Resources

Littelfuse Low Capacitance TVS Diode Array Analysis

Fully automatic inverter and charger circuit

Charger circuit that can restore the vitality of over-discharged batteries

Dry battery charger circuit

Accurate 12V battery automatic charger circuit

Overcurrent protection circuit

Inter-core Communication Method of TMS320C6678 Multi-core DSP: Communication between multi-processor cores is a key and difficult point in multi-core processor programming. For the multi-core communication of the KeyStone architecture TMS320C6678 processor, inter...; Aguilera DSP and ARM Processors

Do a little research: Friends, do you blog? How many blogs do you have? Do you often visit communities like Tianya and Xisi Hutong? What topics do you often pay attention to? It seems that I have too many questions. Haha. ...; 姚yolanda Talking

Looking for a mentor--self-study embedded system: Hello everyone, I am a newcomer, but I would like to use this forum to find a mentor in embedded development. Please understand and support me. I am currently a software testing engineer, mainly engag...; capalh Embedded System

【Keysight Call for Papers】DSO-X 3034A Debugging 485 Receiver Garbled Code: DSO-X 3034A debugs 485 to receive garbled code This content is created by EEWORLD forum netizen [size=3]tziang[/size], if you need to reprint or use it for commercial purposes, you must obtain the aut...; tziang Test/Measurement

Rural hukou is more valuable than urban hukou: In Shanghai, rural household registration is more valuable than resident household registration. The key is that rural houses are built by ourselves, basically on the same residential land....; maoshen Talking

When printf formats the output, it is in relative position. How can I control it relative to the beginning of a line?: I would like to ask everyone a question. Generally, printf formats the output in relative position, relative to the previous character. How can we control it relative to the beginning of a line?...; 虚 Embedded System

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components