EEWORLDEEWORLDEEWORLD

Part Number

Search

10121750-0129055LF

Description
Board Connector
CategoryThe connector    The connector   
File Size411KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

10121750-0129055LF Overview

Board Connector

10121750-0129055LF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid1991773950
Reach Compliance Codecompliant
Country Of OriginMainland China
ECCN codeEAR99
YTEOL9.1
Other featuresTERMINAL PITCH FOR POWER CONTACTS IS 6.35
body width0.57 inch
subject depth0.93 inch
body length4.84 inch
Connector typeBOARD CONNECTOR
Contact arrangementS116P6
Contact to complete cooperationNOT SPECIFIED
Contact point genderMALE
Contact materialCOPPER ALLOY
DIN complianceNO
Filter functionNO
IEC complianceNO
MIL complianceNO
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Mixed contactsYES
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
Number of rows loaded4
OptionsGENERAL PURPOSE
PCB contact row spacing2.54 mm
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts122
UL Flammability Code94V-0
Peng-Bing Fu
Helen Zhang
Shao-Qi Kuang
Pei-Ming Zheng
2012/09/12
2013/05/21
2013/05/21
2013/05/21
-
Released
A
PDS: Rev :A
STATUS:Released
Printed: May 22, 2013

Recommended Resources

Discussion on the method of sending serial data test packets
In serial data testing, a special test fixture is often used to introduce the test signal into the oscilloscope for measurement and analysis. At this time, the serial signal link to be tested is not i...
安_然 Test/Measurement
Find the design method of input current clamp
The current clamping method is to ask if the normal working state is 1ma, the current can pass normally, but if the current exceeds the specified current limit (taking 5ma as an example), it will be c...
leosky568 Test/Measurement
About the problem of DSP chip heating
I hope you guys can tell me: The DSP chip gets a little hot during debugging. What should I consider and solve the problem? 3Q!...
silencesl DSP and ARM Processors
The voltages at the two input terminals of the op amp are different
When using AD8628 as a voltage follower, I found that the voltages of the two input terminals were different, with a difference of 40mv. The output terminal had the same voltage as one of the input te...
dlcnight Analog electronics
How to achieve zero adjustment in AD549
:victory:第一种:The AD549 input offset voltage can be nulled by using balance Pin 1 and Pin 5。 Nulling the input offset voltage in this fashion introduces an added input offset voltage drift component of...
flytosky8 Analog electronics
I would like to ask, is the relay an ESD device? What is the basis?
I would like to ask, is the relay an ESD device? What is the basis?...
zlj740917 Discrete Device

Popular Articles

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1337  965  1422  1602  2622  27  20  29  33  53 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号