/***************************************//* CNPF *//* CC2540 BlueTooth 4.0 learning routine *//*Routine name: Serial communication 1 *//* Creation time: 2018/05/25 *//* Description: You can see it con...
I made something with STC12LE5A32S2. Use timer 0 to generate timing. The timer is like this: void Time0(void) interrupt 1 { ET0 = 0; //Timer 0 interrupt off TH0=0xE5;//(65536-n*FOSC/12/1000)/256;//n=1...
1. In the first and second years of college (laying the foundation) , you must first understand that electrical majors can be divided into two directions: strong electricity and weak electricity. Spec...
I am using an OMAP3530 development board with a built-in GPS module. The WINCE6.0 environment has been established. I downloaded a GPS software from the Internet. I used a USB flash drive to insert th...
Dong Yang, executive vice president of the China Association of Automobile Manufacturers, said on the 26th that according to the authorization of the Ministry of Industry and Information Technology...[Details]
On April 24, Sungrow released its annual financial report. The report shows that in 2017, Sungrow's global shipments reached 16.5GW, of which domestic shipments reached 13.2GW, a year-on-year incre...[Details]
1. Purpose In actual product release, if the program stored in the MCU Flash is not protected, some illegal companies may read the program in the Flash through an emulator (J-Link, ST-Link, e...[Details]
Regarding the PHY construction of LWIP, the PHY chip used is LAN8720A, RMII mode. Regarding the hardware connection part, the Atomic board F407 is used, and the hardware connection is as follows: ...[Details]
introduction STM32 has many registers, which are difficult to remember, so the official packaged two sets of library functions. One is the standard library, but the official has not updated it on F7,...[Details]
I used STM32CubeMX V4.22.1 to generate a project including EHT and Lwip. The debugging has been abnormal. After careful inspection, the following problems were found: 1. The hardware uses LAN8720A, b...[Details]
Serial Port: 一. USART_ITConfig(USART1, USART_IT_TXE, ENABLE): As long as the transmit register is empty, there will always be an interrupt. Therefore, if you are not sending data, turn off the tran...[Details]
Since the first draft of the 5G
NR standard was officially launched at
the end of 2017
, the
5G
commercialization process has taken a substantial step forward. From that moment on, mo...[Details]
Overview
Lightning is a strong discharge phenomenon that occurs between thunderstorm clouds and between thunderstorm clouds and the earth due to severe convective weather. Lightning is gen...[Details]
Nowadays, everyone is saying that "technology is people-oriented". The essence of the development of technology is to serve the improvement of the quality of life of human beings. Automated driving...[Details]
This program mainly uses the comparison output function of the timer to generate PWM waves to control the LED. The comparison output of timer A corresponds to P2.3 P2.4. Therefore, a matching working...[Details]
1. Brief description A summary of "How to build uClinux kernel transplantation on ARMSYS development board with S3C44B0X as core", including the analysis of Bootloader function and the key co...[Details]
According to MEMS Consulting, single-chip radar system-on-chip (SoC) is becoming one of the most popular new sensors . Its widespread adoption in automobiles has greatly increased sales, thereby pr...[Details]
OSC_IN and OSC_OUT are external crystal pins by default. If you do not use an external crystal oscillator on the STM32, how to connect OSC_IN and OSC_OUT If you use the internal RC oscillator instead...[Details]
STM32 ADC multi-channel conversion Description: Use ADC to continuously collect 11 analog signals and transfer them to memory through DMA. ADC is configured to scan and continuously convert mode,...[Details]