85/86 – 5/8 ˝ Square Single-Turn Panel Control with Rotary Switch
Potentiometer Specifications
Standard Resistance Range
Linear Tapers (A, B, E, & H)......................................................................... (B & E) 1 K ohms to 1 megohm ................. (A & H) 100 ohms to 1 megohm
Audio Tapers (C, D, F, G, S, & T) ................................................................ (D, G, S, & T) 1 K ohms to 1 megohm ....... (C & F) 1 K ohms to 1 megohm
Total Resistance Tolerance................................................................................. ±20 % or 10 %............................................ ±10 % or 5 %
Operating Temperature Range ........................................................................... -40 °C to +125 °C ....................................... -40 °C to +125 °C
Storage Temperature Range .............................................................................. -55 °C to +125 °C ....................................... -55 °C to +125 °C
Temperature Coefficient Over Storage Temperature Range .............................. ±1,000 ppm/°C ........................................... ±150 ppm/°C
Vibration (Single Section) ................................................................................... 15 G ........................................................... 15 G
Total Resistance Shift .................................................................................. ±2 % maximum .......................................... ±2 % maximum
Voltage Ratio Shift ....................................................................................... ±5 % maximum .......................................... ±5 % maximum
Shock (Single Section) ....................................................................................... 30 G ........................................................... 30 G
Total Resistance Shift .................................................................................. ±2 % maximum .......................................... ±2 % maximum
Voltage Ratio Shift ....................................................................................... ±5 % maximum .......................................... ±5 % maximum
Load Life ............................................................................................................. 1,000 hours ................................................ 1,000 hours
Total Resistance Shift .................................................................................. ±10 % maximum ........................................ ±5 % maximum
Rotational Life (No Load).................................................................................... 100,000 cycles ........................................... 100,000 cycles
Total Resistance Shift .................................................................................. (Linear taper) 10 ohms or .......................... (All tapers) ±5 % TRS maximum
Moisture Resistance (MIL-STD-202, Method 103, Condition B)
Total Resistance Shift .................................................................................. (B & E tapers) ±10 % maximum ................ ±5 % maximum (all tapers)
Starting and Running Torque (Non-Locking Bushings)
Single Section..................................................................................................................................................................................0.14 to 1.06 N-cm (0.2 to 1.5 oz.-in.)
Dual Section ....................................................................................................................................................................................0.14 to 1.06 N-cm (0.2 to 1.5 oz.-in.)
Triple Section ...................................................................................................................................................................................0.35 to 1.41 N-cm (0.5 to 2.0 oz.-in.)
Quadruple Section ...........................................................................................................................................................................0.35 to 1.41 N-cm (0.5 to 2.0 oz.-in.)
Starting and Running Torque (Locking Bushings) ....................................................................................................................0.14 to 2.82 N-cm (0.2 to 4.0 oz.-in.)
Shaft Locking Torque with Locknut @ 10 in-lb. (B & E Bushings) .......................................................................................................................14 N-cm (20 oz-in.)
Mounting ...................................................................................................................................................................................1.7-2.0 N-m (15-18 lb.-in.) maximum
Weight (Single Section) ............................................................................................................................................................................................. 21 grams maximum
(Each Additional Section)...................................................................................................................................................................................... 6 grams maximum
Terminals ...........................................................................................................................................................................................Printed circuit terminals or J-Hooks
Soldering Condition .................................................................................. Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ˝ wire diameter.
Maximum temperature 399 °C (750 °F) for 3 seconds. No wash process to be used with no clean flux.
Marking ...........................................................................................Manufacturer’s trademark, wiring diagram, date code and resistance, manufacturer’s part number
Ganging (multiple section potentiometers) ...................................................................................................................................................................... 4 cup maximum
Hardware ...............One lockwasher and one mounting nut is shipped with each potentiometer; locking bushing versions are shipped with one additional locking nut
For dimensional drawings see pages 3 & 4. For ordering information see page 5.
NOTE: Model 81/82 performance specifications do not apply to units subjected to printed circuit board cleaning procedures.
1
Electrical specifications tested at 250 RPM, at room ambient: +25 °C nominal.
Initial Electrical Characteristics
1
Conductive Plastic Element
Cermet Element
Environmental Characteristics
1
Mechanical Characteristics
WARNING
Cancer and Reproductive Harm
www.P65Warnings.ca.gov
*RoHS Directive 2015/863, Mar 31, 2015 and Annex.
Specifications are subject to change without notice. Users should verify actual device performance in their specific
applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the
last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
81/82 – 5/8 ˝ Square Single-Turn Panel Control
85/86 – 5/8 ˝ Square Single-Turn Panel Control with Rotary Switch
Rotary Switch Specifications
Initial Electrical Characteristics
1
Contacts:
DPST ............................................................................................................................................................................. N.O/N.O.,N.C./N.C. or N.O./N.C.
Power Rating (Resistive Load):
DPST ..........................................................................................................2 A @ 125 volts RMS-60 Hz or 2 A @ 28 VDC, 1 A @ 250 volts RMS-60 Hz
Operating Temperature Range ...................................................................................................................................................................... -40 °C to +70 °C
Storage Temperature Range ....................................................................................................................................................................... -65 °C to +125 °C
Vibration (Dual Section)......................................................................................................................................................................................................8 G
(Triple Section) ..................................................................................................................................................................................................5 G
(Quadruple Section) ..........................................................................................................................................................................................3 G
Contact Resistance .......................................................................................................................................................................10 milliohms maximum
Contact Bounce ......................................................................................................................................................................... 0.1 millisecond maximum
Shock (Dual Section) ........................................................................................................................................................................................................20 G
(Triple Section) ....................................................................................................................................................................................................15 G
(Quadruple Section) ............................................................................................................................................................................................10 G
Contact Resistance .......................................................................................................................................................................10 milliohms maximum
Contact Bounce ......................................................................................................................................................................... 0.1 millisecond maximum
Switch Actuating Torque (50% Duty cycle @ Rated Power Load) .................................................................................1.41 to 4.94 N-cm (2 to 7 oz.-in.)
Contact Resistance .....................................................................................................................................................................100 milliohms maximum
Moisture Resistance (MIL-STD-202, Method 106, Condition B)
Contact Resistance (0.1 VDC-10 mA) ..........................................................................................................................................10 milliohms maximum
Switch Housing Material ................................................................................................................. High temperature, flame retardant, thermosetting plastic
Mechanical Characteristics
1
Actuating Torque (Each Section, Switch Module Only) ......................................................................................................3.53 to 10.6 N-cm (5 to 15 oz.-in.)
Running Torque (Out of Detent, 2-4 Module Assembly) ....................................................................................................0.21 to 1.41 N-cm (0.3 to 2 oz.-in.)
Detent ....................................................................................................................................................................................................CW or CCW standard
Contact Materials......................................................................................................................................................................... Fine silver with gold overlay
Terminal Styles .................................................................................................................................................................................................Solder lug only
Standard Orientation .............................................................................................................................................................In-line with control terminals
Optional .........................................................................................................................................................................Rotated 90 ° CCW from standard
Terminal Strength (Before and After Soldering Heat Exposure) ........................................................................................................ 0.9 Kg (2 lbs.) minimum
1
NOTE: Model 81/82 performance specifications do not apply to units subjected to printed circuit board cleaning procedures.
Electrical specifications tested at 250 RPM, at room ambient: +25 °C nominal.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
Terminal outlines shown as solid lines represent PC Pins, available
on Model 81. Dashed line terminal outline represents "J" Hook,
available on Model 82.
5.97 ± .38
(.235 ± .015)
5.08 ± .38
(.200 ± .015)
12.7
(.50)
5.33 ± .76
(.210 ± .03)
10.16 ± .13
(.400 ± .005)
Note: For units with dual concentric shaft styles, a
2.54 (.100) spacer is added between the module(s) driven
by the outer shaft and those driven by the inner shaft.
For G, K, or V shafts, add the spacer between
modules 1 and 2. For L or M shafts, add the spacer
between modules 2 and 3. For N or P shafts, add the
spacer between modules 3 and 4.
SLOTTED SHAFT
*EXCLUDES MODELS 83 AND 84
DIMENSIONS:
MM
(INCHES)
Suggested Panel Layout
B
C
BUSHING
A, B & J
E
DIM A
9.91
(.39)
ANTI-ROTATION LUG
A
B
C
E
F
J
K
DIM B
7.75
(.305)
7.75
(.305)
N/A
13.49
(.531)
N/A
9.53
(.375)
9.53
(.375)
DIM C
N/A
7.75
(.305)
7.75
(.305)
N/A
N/A
N/A
9.53
(.375)
DIM D
N/A
N/A
N/A
N/A
7.75
(.305)
N/A
N/A
DIM E
2.49
(.098)
2.49
(.098)
2.49
(.098)
3.45
(.136)
2.54
(.100)
2.54
(.100)
2.54
(.100)
D
A
C, E & N
R&S
U
6.73
(.265)
10.5
(.413)
7.5
(.295)
DIMENSIONS:
MM
(INCHES)
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
85/86 – 5/8 ˝ Square Single-Turn Panel Control with Rotary Switch
Product Dimensions
Primary Potentiometer Module
Model 85/86
14.53
(.572)
9.58 ± .38
(.377 ± .015)
Secondary Potentiometer Module
Model 85/86
10.16
(.400)
15.88
(.625)
15.88
(.625)
Shaft Flat Orientation*
120 ° ± 5 ° CCW END
30 ° ± 5 °
12.7
(.50)
5.97
(.235)
8.56
(.337)
1.60
(.063)
FLATTED SHAFT
5.08
(.200)
SLOTTED SHAFT
*EXCLUDES MODELS 83 AND 84
5.08
(.200) 8.56
(.337)
5.08
(.200)
Switch Module
Model 85/86
REAR
PLATE
COVER
2.77
(.109)
1.35
(.053)
2.29
(.090)
TYP.
6 PLACES
Assembly Sequence
Model 85/86
Secondary Potentiometer Module
Switch Module Terminal Orientation
3
1
4
2
3
1
18.42
(.725)
2.41
1.14
(.095)L X (.045)W
SLOT TYP. 6 PLACES
4
2
HORIZONTAL ORIENTATION
(Types R56, R57, R58 & R59)
VERTICAL ORIENTATION
(Types R50, R51, R52 & R53)
2.92
(.115)
9.53
(.375)
REAR
COVER
PLATE
SWITCH
MODULE
PRIMARY
POTENTIOMETER
MODULE
4
2
3
1
3
1
4
2
DPST (NO/NC)
(TYPES 50, 51, 56, 57)
DPST (NO/NO)
(TYPES 52, 53, 58, 59)
Switch contacts shown in detent position.
Locating Lug Options - All Model 80 Series
A
.46
(.018)
7.75
(.305)
E
13.49
(.531)
J
9.53
(.375)
.79 ± .41
(.031 ± .016)
E = 2.36 ± .76
(.093 ± .03)
H & J = 1.98 ± .41
(.078 ± .016)
2.31
(.091)
3.18
(.125)
.46
(.018)
2.36
(.093)
7.75
(.305)
A
C
7.75
(.305)
.46
(.018)
.79 ± .41
(.031 ± .016)
MOUNTING
SURFACE
TOLERANCES EXCEPT AS SHOWN: DECIMAL .XXX ±
RECOMMENDED
PANEL LAYOUT
7.75
#40 DRILL
(.305)
2.49
DIA.
(.098)
9.91
DIA.
(.390)
.127
(.005)
.XX ± .38
(.015)
ANGLE ± 5 %
2.31
(.091)
DIMENSIONS:
MM
(INCHES)
NOTE: "D" OPTION - NO A/R LUG. OTHER LOCATING LUG OPTIONS AVAILABLE. CONSULT FACTORY FOR DETAILS.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
Test access port TAPTAP (Test Access Port) is a general port. Through TAP, all data registers (DR) and instruction registers (IR) provided by the chip can be accessed . The control of the entire TAP i...
[i=s]This post was last edited by johnrey on 2014-8-10 16:55[/i] [align=left][font=宋体]The reason why the project is called Waiting for the Light Waiting for the Light is because it is related to light...
LED lighting has a promising future as prices continue to fall and technology continues to advance. ITRI predicts that LED lighting will grow significantly starting from 2011, and the size of Taiwan's...
According to foreign media reports, Ford Motor has applied to the U.S. Patent and Social Security Administration (USPTO) for a patent for a remote vehicle control system that may be used in future ...[Details]
ISP devices, such as field programmable devices (FPGAs and CPLDs), do not require a programmer. Using programming kits provided by the device manufacturer, they employ a top-down modular design app...[Details]
To understand why car engines need gearboxes, we must first understand the characteristics of different types of engines. An engine refers to a machine that can convert a form of energy into kineti...[Details]
Recently,
Xpeng Motors and Xinlian Integrated Circuit jointly announced the mass production of China's first hybrid silicon carbide product.
Designed and developed by Xpeng Motors and joint...[Details]
Core point: The automotive industry chain and the humanoid robot industry have collaborative advantages in hardware, software, and scenarios. Upstream and downstream companies in the automotive ind...[Details]
In June 2014, the Ministry of Industry and Information Technology issued 4G FD-LTE licenses to China Unicom and China Telecom. Together with the 4G TD-LTE licenses issued to China Mobile, China Uni...[Details]
Pure electric vehicles, structurally speaking, have components such as a power battery. In addition to the power battery, a small battery also powers some low-voltage electrical components and even...[Details]
With the advent of the electric car era, the number of pure electric vehicles has increased significantly, but many car owners do not know how to properly maintain pure electric vehicles. In additi...[Details]
Permanent magnets are essential components in a wide range of household and industrial devices. They are particularly crucial in the renewable energy sector, including electric vehicle motors. Curr...[Details]
In the electronics manufacturing industry, surface mount technology (SMT) placement machines are core equipment for production lines. However, with many different models available on the market, ch...[Details]
1. Multi-channel DAC technology bottleneck
Currently,
the development of multi-channel DAC technology focuses on two core challenges.
First, industrial applications urgently ...[Details]
The 2025 China International Automotive Testing Exhibition will be held at the Shanghai World Expo Exhibition and Convention Center from August 27 to 29, 2025.
Clacton Seafront, UK, ...[Details]
Speaking of the problem of vehicle spontaneous combustion, whether it is a pure electric vehicle or a fuel vehicle, there will be incidents of spontaneous combustion. For the same spontaneous combu...[Details]
When American cartoonist Chester Gould sketched the watch on Dick Tracy's wrist, he had no idea that science fiction would become reality 70 years later. As a comic strip artist, Gould imagined fut...[Details]
Analog Devices held a third-quarter fiscal 2025 earnings conference call. Vincent T. Roche, CEO and Chairman of the Board, and Richard C. Puccio, Executive Vice President and Chief Financial Office...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
