EEWORLDEEWORLDEEWORLD

Part Number

Search

K504120B1FC1S

Description
Bridge Rectifier Diode, 1 Phase, Silicon,
CategoryDiscrete semiconductor    diode   
File Size22KB,1 Pages
ManufacturerMicrosemi
Websitehttps://www.microsemi.com
Download Datasheet Parametric View All

K504120B1FC1S Overview

Bridge Rectifier Diode, 1 Phase, Silicon,

K504120B1FC1S Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
Objectid1440010051
package instructionR-XXMA-X
Reach Compliance Codecompliant
ECCN codeEAR99
YTEOL0
Minimum breakdown voltage1200 V
ConfigurationBRIDGE, 4 ELEMENTS
Diode component materialsSILICON
Diode typeBRIDGE RECTIFIER DIODE
JESD-30 codeR-XXMA-X
Number of components4
Phase1
Package body materialUNSPECIFIED
Package shapeRECTANGULAR
Package formMICROELECTRONIC ASSEMBLY
Peak Reflow Temperature (Celsius)NOT SPECIFIED
Certification statusNot Qualified
Maximum repetitive peak reverse voltage1200 V
surface mountNO
Terminal formUNSPECIFIED
Terminal locationUNSPECIFIED
Maximum time at peak reflow temperatureNOT SPECIFIED
The video signal carrying capacity close to 1MHz is not enough. What op amp can I use to design a voltage follower?
As the title says, the video signal current output by the linear array CMOS is too small, and the input resistance of the AD module used is only 50ohm. I want to use an op amp to design a voltage foll...
XuYong虚庸 Analog electronics
How does STM32 make AD continuously sample and then delay 500MS before DA continuously outputs
This is my current graduation project: using the AD and DA built into the STM32F103ZET6 chip, the waveform is first continuously collected by the AD and stored in the external SRAM. After 500MS, the C...
wjg2954 stm32/stm8
Research on voice acquisition system and external communication interface based on DSP.pdf
Research on voice acquisition system and external communication interface based on DSP.pdf...
yunhuihe DSP and ARM Processors
Why are the upper and lower rows of pins not parallel when laying out AD devices?
When drawing a minimum system board for STM32, why do the four 2.54*10 pin headers on the top and bottom seem to be bent, wider on the left and narrower on the right?...
littleshrimp Talking
Why does it say here that RBPU needs to be defined?
//----------------------------------------------------------------- // Name: RB port level change interrupt controls the switch of two-digit digital tubes, addition and subtraction display//----------...
嘻嘻嘻嘻啊啊 Microchip MCU
[LPC54100] Wanli board super simple reverse
[i=s]This post was last edited by freebsder on 2015-3-22 14:07[/i] First of all, I want to complain! The schematic is lousy. I have been asking them for it since the board was sent on Monday. It has b...
freebsder MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2264  1089  1157  1373  2545  46  22  24  28  52 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号