CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Surface Mount
@Super
low ESR, impedance and high heat resistance have been obtained by using con-
ductive polymer as electrolyte.
@Suitable
for DC-DC converters, voltage regulators and decoupling applications.
@Endurance
: 125C 1,000 hours
@Rated
voltage range : 2.5 to 20V
dc
, Capacitance range : 22 to 1,000MF
@Case
size range :
F6.3B5.7L
to
F10B7.7L
@RoHS
Compliant
PXH
Higher temperature
PXA
?SPECIFICATIONS
Items
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
-55 to +125C
2.5 to 20V
dc
P20%
(M)
Rated voltageB1.15
Shall not exceed values shown in STANDARD RATINGS.
0.12 max.
Z(-25C)/Z(+20C)[1.15
Z(-55C)/Z(+20C)[1.25
Characteristics
(at 20C, 120Hz)
(at 125C)
(at 20C after 2 minutes)
(at 20C, 120Hz)
Bias Humidity
Surge Voltage
Failure Rate
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 1,000 hours
at 125C.
Appearance
No significant damage
Capacitance change
[P20%
of the initial value
DF (tanE)
[200%
of the initial specified value
ESR
[200%
of the initial specified value
Leakage current
[The
initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to the DC rated voltage at
60C, 90 to 95% RH for 1,000 hours.
Appearance
No significant damage
Capacitance change
[P20%
of the initial value
DF (tanE)
[150%
of the initial specified value
ESR
[150%
of the initial specified value
Leakage current
[The
initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 125C for 30 seconds
through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change
[P20%
of the initial value
DF (tanE)
[150%
of the initial specified value
ESR
[150%
of the initial specified value
Leakage current
[The
initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 125C)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 125C.
?DIMENSIONS
[mm]
@Terminal
Code : A
FDP0.5
BP0.2
W
P
CP0.2
Size code
F60
H70
J80
fD
6.3
8
10
L
5.7
6.7
7.7
A
B
C
6.6 6.6 7.2
8.3 8.3 9.0
10.3 10.3 11.0
W
0.5 to 0.8
0.7 to 1.1
0.7 to 1.1
P
1.9
3.1
4.5
?MARKING
EX) 20V22MF
H
39F
22
20
V
0.3max.
LP0.3
AP0.2
?PART
NUMBERING SYSTEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
A PXH
AAA
A RA
AAA
M
AAA
G
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 22MF:220,100MF:101)
Taping code
Terminal code
Voltage code (ex. 6.3V:6R3,10V:100)
Series code
Category
Please refer to "Product code guide (conductive polymer type)"
(1/2)
CAT. No. E1001K
Industrial Control Electronics
京公网安备 11010802033920号
EEWORLD
