LT3653E .............................................–40°C to 125°C
LT3653I ..............................................–40°C to 125°C
Storage Temperature..............................–65°C to 150°C
DCB PACKAGE
8-LEAD (2mm 3mm) PLASTIC DFN
θ
JA
= 64°C/W,
θ
JC
= 10°C/W
EXPOSED PAD (PIN 9) IS GND, MUST BE SOLDERED TO PCB
ORDER INFORMATION
LEAD FREE FINISH
LT3653EDCB#PBF
LT3653IDCB#PBF
TAPE AND REEL
LT3653EDCB#TRPBF
LT3653IDCB#TRPBF
PART MARKING*
LDJN
LDJN
PACKAGE DESCRIPTION
8-Lead (2mm
×
3mm) Plastic DFN
8-Lead (2mm
×
3mm) Plastic DFN
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C; V
IN
= 12V, V
BOOST
= 17V, V
SW
= 0V, R
ILIM
= 33.2k, unless otherwise noted.
PARAMETER
V
IN
Operating Range
V
IN
Undervoltage Lockout
V
IN
Undervoltage Hysteresis
V
IN
Overvoltage Lockout
V
IN
Overvoltage Lockout Hysteresis
V
IN
Supply Current
V
OUT
Reverse Leakage Current
V
OUT
Nominal Set Point
V
OUT
Current Limit Range
V
OUT
Current Limit
Operating Frequency
V
C
Source Current
V
C
Sink Current
V
C
Switching Threshold
V
OUT
= 0V, V
C
= 1.5V
V
OUT
= 5V, V
C
= 1.5V
I
OUT
= 0mA
R
ILIM
= 33.2k
Not Switching
V
IN
= 0V, V
OUT
= 4.8V
V
IN
= Open, V
OUT
= 4.8V
V
C
Pin = Open
l
l
l
ELECTRICAL CHARACTERISTICS
CONDITIONS
MIN
l
TYP
7
500
33
1
2.8
MAX
30
7.5
36
3.4
1
1
UNITS
V
V
mV
V
V
mA
μA
μA
V
A
A
A
kHz
μA
μA
V
7.5
6.5
30
Rising
Rising
4.8
0.4
0.85
0.80
1350
1
1
1500
12
10
1.1
5
1.2
1.15
1.2
1650
3653f
2
LT3653
ELECTRICAL CHARACTERISTICS
PARAMETER
V
C
Clamp Voltage
Switch Peak Current Limit
Switch V
CESAT
Boost Diode Drop
Boost Pin Current
HVOK Output Voltage High
HVOK Output Voltage Low
CONDITIONS
V
OUT
= 0V
(Note 4)
I
SW
= 1A
I
DIODE
= 60mA
I
SW
= 1A
I
HVOK
= 1mA
I
HVOK
= –2μA
l
l
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C; V
IN
= 12V, V
BOOST
= 17V, V
SW
= 0V, R
ILIM
= 33.2k, unless otherwise noted.
MIN
TYP
1.75
2
275
0.9
28
4
4.4
5
0.25
1.2
MAX
UNITS
V
A
mV
V
mA
V
V
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
The LT3653E is guaranteed to meet performance specifications
from 0°C to 125°C. Specifications over the –40°C to 125°C operating
temperature range are assured by design, characterization, and correlation
with statistical process controls. The LT3653I specifications are
guaranteed over the full –40°C to 125°C temperature range. High junction
temperatures degrade operating lifetimes. Operating lifetime is derated at
junction temperatures greater than 125°C.
Note 3:
Absolute Maximum Voltage at V
IN
pin is 60V for non-repetitive
1 second transients.
Note 4:
Switch Peak Current Limit guaranteed by design and/or correlation
to static test.
Note 5:
This IC includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature will exceed the maximum operating junction temperature
when overtemperature protection is active. Continuous operation above
the specified maximum operating junction temperature may impair device
reliability.
3653f
3
LT3653
TYPICAL PERFORMANCE CHARACTERISTICS
Switch Voltage Drop
400
350
SWITCHING FREQUENCY (MHz)
SWITCH VOLTAGE DROP (mV)
300
250
200
150
100
50
0
0
0.2
0.4
0.6
0.8
SWITCH CURRENT (A)
1
1.2
3653 G01
T
A
= 25°C unless otherwise noted
Switching Frequency
125ºC
25ºC
1.7
1.6
INPUT VOLTAGE (V)
1.5
1.4
1.3
1.2
1.1
1.0
–50
8.0
7.5
Undervoltage Lockout
RISING
7.0
6.5
6.0
5.5
5.0
4.5
-25
0
25
50
75
TEMPERATURE (ºC)
100
125
4.0
–50 -25
0
25 50 75 100 125 150
TEMPERATURE (ºC)
3653 G03
–45ºC
FALLING
3653 G02
Output Current Limit
1.2
R
ILIM
= 33.2k
1.15
OUTPUT VOLTAGE (V)
1.1
CURRENT LIMIT (A)
1.05
1
0.95
0.9
0.85
0.8
–50 –25
0
25
50
75
TEMPERATURE (ºC)
100
125
1
0
5
4
3
2
6
Output Current Limit
R
ILIM
= 27.4k
35
V
IN
Overvoltage Lockout
RISING
INPUT VOLTAGE (V)
33
FALLING
31
29
27
25
–50
0
0.2
0.4 0.6 0.8
1
OUTPUT CURRENT (A)
1.2
1.4
–25
0
25
50
75
TEMPERATURE (ºC)
100
125
3653 G04
3653 G05
3653 G06
BOOST Pin Current
35
30
BOOST PIN CURRENT (mA)
BOOST DIODE V
F
(V)
25
20
15
10
5
0
1.4
1.2
1
0.8
0.6
0.4
0.2
0
Boost Diode V
F
0
0.2
0.4
0.5
0.8
SWITCH CURRENT (A)
1
1.2
3653 G07
0
50
100
150
200
DIODE CURRENT (mA)
250
300
3653 G08
3653f
4
LT3653
TYPICAL PERFORMANCE CHARACTERISTICS
V
C
Current
15
10
VC PIN CURRENT (μA)
5
0
–5
–10
–15
–20
–25
4
4.4
4.8
5.2
V
OUT
(V)
5.6
6
3653 G09
T
A
= 25°C unless otherwise noted
V
C
Operating Range
2.0
1.8
1.6
VC VOLTAGE (V)
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
-50
-25
0
25
50
75
TEMPERATURE (ºC)
100
125
SWITCHING THRESHOLD
CURRENT LIMIT CLAMP
3653 G10
PIN FUNCTIONS
V
IN
(Pin 1):
The V
IN
pin supplies current to the LT3653’s
internal regulator and the internal power switch. Locally
bypass this pin with a capacitor.
HVOK (Pin 2):
The HVOK pin is a status pin which indi-
cates that the internal bias rail is present and that an input
undervoltage lockout fault, an overvoltage lockout fault or
an over temperature fault are not present.
V
C
(Pin 3):
The V
C
pin is the output of the internal error
amplifier and is internally compensated. The voltage on this
pin controls the peak switch current. Connect this pin to
the battery charger V
C
pin for battery tracking function.
I
LIM
(Pin 4):
Connect a resistor to GND to program the
output current limit of the regulator. See the I
LIM
Resistor
section in Application Information.
V
OUT
(Pin 5):
The V
OUT
pin is connected to the negative
terminal of the internal current sense resistor of the output
current limit circuit. Maximum V
OUT
voltage is regulated
to 4.8V.
I
SENSE
(Pin 6):
The I
SENSE
pin is the positive input to the
internal current sense resistor of the output current limit
circuit. The I
SENSE
pin is also the anode of the internal
BOOST diode.
BOOST (Pin 7):
The BOOST pin provides a drive voltage,
higher than the input voltage, to the internal power switch.
The BOOST pin is internally connected to the cathode of
the BOOST diode.
SW (Pin 8):
The SW pin is the output of the internal power
switch. Connect this pin to the inductor, catch diode and
boost capacitor.
Exposed Pad (Pin 9):
Ground. The Exposed Pad must be
soldered to the PCB and electrically connected to ground.
Use a large ground plane and vias to optimize thermal
Whether it is a work log, a weekly summary, or a monthly plan, you can write it out every day. But the key is to do it step by step. What can be done in one day takes three days. The efficiency is low...
[i=s] This post was last edited by ignorant carrot on 2015-9-18 17:47 [/i] I am a novice. I looked at the fpu_hardware in the example in controlSUITE and the previous comments [code] //###############...
Does anyone have English materials on computer control technology? The kind used for papers! About 2000 words or a website is also fine. My email address is feihu618@126.com...
Use busybox to make a file system, compiler: arm-linux-gcc 4.3.2, busybox 1.13.3, dynamic compilation. How do I know which libraries are needed? Some articles say to use: arm-linux-readelf -d busybox ...
How do I calculate the timing of FSMC? I use 103ZE to drive CS8900A and IS61LV25616. CS8900A works in IO mode, but the initialization is not correct. The same circuit works well on 710. I suspect that...
The core of a machine vision system is image acquisition and processing. All information comes from images, and image quality is crucial to the entire vision system. A good image can improve the st...[Details]
How do you know if a machine is operating properly? The answer: by leveraging deep learning to detect anomalies in routine vibration data from industrial machines. Anomaly detection has many uses, ...[Details]
Nios II is a configurable 16-/32-bit RISC processor. Combined with a rich set of peripheral-specific instructions and hardware acceleration units, it provides a highly flexible and powerful SOPC sy...[Details]
Is electromagnetic radiation from electric vehicles harmful to the human body? Recently, the issue of electromagnetic radiation from electric vehicles has garnered widespread attention. However, pu...[Details]
Long ago, the lifespan of cars in my country was 15 years. Once a car reached 15 years old, it was forced to be scrapped. However, the policy was later changed. As long as the car does not exceed 6...[Details]
1 Introduction
In the mid-1960s, American scientist Maas conducted extensive experimental research on the charging process of open-cell batteries and proposed an acceptable charging curve for ...[Details]
With the rapid adoption of smart electric vehicles, automotive chips are evolving from auxiliary control units to the foundation of the entire vehicle's intelligence. Their applications extend from...[Details]
On August 21, WeRide officially launched WePilot AiDrive, a one-stage end-to-end assisted driving solution developed in cooperation with Bosch. This comes only half a year after the two parties' "t...[Details]
For autonomous vehicles to safely navigate the road, they must identify far more complex objects than just traffic lights, pedestrians, and other familiar objects. Among these obstacles is a crucia...[Details]
With the increasing popularity of automated equipment, linear modules, a common auxiliary device for automated equipment, have also seen a bright future. In particular, in recent years, many small ...[Details]
On August 21, according to a report by Korean media SEDaily yesterday, according to semiconductor industry sources, the HBM4 samples provided by Samsung to Nvidia last month have passed initial tes...[Details]
Qiangmao, your trusted semiconductor solutions partner, sincerely invites you to visit Electronics India 2025, South Asia's leading trade show for electronic components, systems, applications...[Details]
introduction
As core electronic components used in vastly different fields, automotive-grade chips and mobile/consumer-grade chips exhibit significant differences in their...[Details]
With the growth of the Internet of Things (IoT), wearable, and portable devices, consumers are growing weary of cluttered cables and the need for frequent battery recharges. The benefits of wireles...[Details]
As the power density of modern electronic systems continues to increase, effective thermal management has become critical to ensuring system performance, reliability, and longevity—especially in hi...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
