EEWORLDEEWORLDEEWORLD

Part Number

Search

8AD050P-326RBB

Description
Rectangular Connector, 50 Contact(s), Male, 0.05 inch Pitch, Receptacle
CategoryThe connector    The connector   
File Size386KB,7 Pages
ManufacturerFreeport Resources Enterprises Corp
Download Datasheet Parametric View All

8AD050P-326RBB Overview

Rectangular Connector, 50 Contact(s), Male, 0.05 inch Pitch, Receptacle

8AD050P-326RBB Parametric

Parameter NameAttribute value
Objectid1166345072
Reach Compliance Codeunknown
ECCN codeEAR99
body width0.362 inch
subject depth0.403 inch
body length1.504 inch
Body/casing typeRECEPTACLE
Connector typeRECTANGULAR CONNECTOR
Contactor designPREASSEM CONN
Contact to complete cooperationAU ON NI
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact resistance35 mΩ
Contact styleSQ PIN-SKT
Dielectric withstand voltage250VAC V
Insulation resistance500000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYBUTYLENE TEREPHTHALATE
Plug contact pitch0.05 inch
Match contact row spacing0.1 inch
Installation option 1#4-40
Installation option 2THREADED BRACKET
Number of rows loaded2
Maximum operating temperature85 °C
Minimum operating temperature-25 °C
Plating thickness15u inch
Rated current (signal)1 A
GuidelineUL
Shell surfaceNICKEL
Total number of contacts50
DSP/BIOS TSK_sleep()
I would like to ask you why the task cannot be woken up again after calling the bios system function TSK_sleep(...) in the task program when programming based on DSP/BIOS. Thank you in advance....
feifei Microcontroller MCU
lm3s101 input signal
In the pdf, I see that 0.4v or less is a low level, and 2v or more is a high level. So will the signal sampled between 0.4v and 2v be considered a high level or a low level? If you don't know 101, you...
sciencekn1 Microcontroller MCU
I2C interface problem of PIC16F877A
I want to use a PIC16F877A as a slave device of the I2C interface. After writing the program and burning it, I found that the clock at the SCL end could not be input. After a period of time, when I in...
old——Jia Microchip MCU
dsp28335 AD sampling single mode
[p=28, null, left][color=rgb(69, 69, 69)]Three modes are configured: single mode, continuous mode and DMA transfer[/color][/p][p=28, null, left][color=rgb(69, 69, 69)]Single mode calls the acquisition...
fish001 DSP and ARM Processors
How to use circuit to stabilize signal?
I want to stabilize the signal output by the low-frequency power amplifier without using a task chip. Can I use some simple components to stabilize the signal? Please give me some advice! Thank you in...
jackiesh Embedded System
XTR111 4-20mA circuit problem
As shown in the figure below, the official 4-20mA schematic diagram is imitated. Since the microcontroller does not have DA, DAC7512 is used. During the debugging process, it is found that the 5V outp...
zixialong Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 849  1333  2243  2693  745  18  27  46  55  15 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号