Feature - No dead cycles between write and read cycles
Internally synchronized output buffer enable eliminates the
need to control
OE
Single R/W (READ/WRITE) control pin
W
Positive clock-edge triggered address, data, and control
signal registers for fully pipelined applications
4-word burst capability (interleaved or linear)
Individual byte write (BW
1
-
BW
4
) control (May tie active)
BW
Three chip enables for simple depth expansion
3.3V power supply (±5%)
3.3V I/O Supply (V
DDQ
)
Power down controlled by ZZ input
Packaged in a JEDEC standard 100-pin plastic thin quad
flatpack (TQFP), 119 ball grid array (BGA) and 165 fine pitch
ball grid array(fBGA).
Description
The IDT71V65603/5803 are 3.3V high-speed 9,437,184-bit
(9 Megabit) synchronous SRAMS. They are designed to eliminate dead bus
cycles when turning the bus around between reads and writes, or writes and
reads. Thus, they have been given the name ZBT
TM
, or Zero Bus Turnaround.
Address and control signals are applied to the SRAM during one clock
cycle, and two cycles later the associated data cycle occurs, be it read or write.
The IDT71V65603/5803 contain data I/O, address and control signal
registers. Output enable is the only asynchronous signal and can be used
to disable the outputs at any given time.
A Clock Enable (CEN) pin allows operation of the IDT71V65603/5803 to
be suspended as long as necessary. All synchronous inputs are ignored when
(CEN) is high and the internal device registers will hold their previous values.
There are three chip enable pins (CE1, CE2,
CE2)
that allow the user
to deselect the device when desired. If any one of these three are not asserted
when ADV/LD is low, no new memory operation can be initiated. However,
any pending data transfers (reads or writes) will be completed. The data bus
will tri-state two cycles after chip is deselected or a write is initiated.
The IDT71V65603/5803 have an on-chip burst counter. In the burst
mode, the IDT71V65603/5803 can provide four cycles of data for a single
address presented to the SRAM. The order of the burst sequence is
defined by the
LBO
input pin. The
LBO
pin selects between linear and
interleaved burst sequence. The ADV/LD signal is used to load a new
external address (ADV/LD = LOW) or increment the internal burst counter
(ADV/LD = HIGH).
The IDT71V65603/5803 SRAM utilize IDT's latest high-performance
CMOS process, and are packaged in a JEDEC Standard 14mm x 20mm 100-
pin thin plastic quad flatpack (TQFP) as well as a 119 ball grid array (BGA) and
165 fine pitch ball grid array (fBGA) .
Pin Description Summary
A
0
-A
18
Address Inputs
Chip Enables
Output Enable
Read/Write Signal
Clock Enable
Individual Byte Write Selects
Clock
Advance burst address / Load new address
Linear / Interleaved Burst Order
Sleep Mode
Data Input / Output
Core Power, I/O Power
Ground
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
I/O
Supply
Supply
Synchronous
Synchronous
Asynchronous
Synchronous
Synchronous
Synchronous
N/A
Synchronous
Static
Asynchronous
Synchronous
Static
Static
5304 tbl 01
CE
1
, CE
2
,
CE
2
OE
R/
W
CEN
BW
1
,
BW
2
,
BW
3
,
BW
4
CLK
ADV/
LD
LBO
ZZ
I/O
0
-I/O
31
, I/O
P1
-I/O
P4
V
DD
, V
DDQ
V
SS
ZBT and Zero Bus Turnaround are trademarks of Integrated Device Technology, Inc. and the architecture is supported by Micron Technology and Motorola, Inc.
Today's computer peripherals are pursuing high speed and high versatility. In order to meet user needs, seven companies led by Intel launched the USB (Universal Serial Bus) bus protocol in 1994, wh...[Details]
Hardware designers have begun to adopt FPGA technology in high-performance DSP designs because it can provide 10-100 times faster computing than PC-based or microcontroller-based solutions. Previou...[Details]
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
When the WDP500-2A plane grating monochromator is used to test the emission wavelength of a high-power laser diode at different currents, the matching of the laser diode has the disadvantages of lo...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
1 Introduction
With the acceleration of the pace of urban modernization, society has higher requirements for urban road lighting and urban lighting projects. The state has clearly required tha...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
The solidification and modularization of intelligent video analysis algorithms are the current trends in the application of intelligent video analysis technology. It perfectly combines intelligent ...[Details]
1. Principle of displacement angle sensor
The angle sensor is used to detect angles. It has a hole in its body that fits the LEGO axle. When connected to the RCX, the angle sensor counts once ...[Details]
Instrument stepper motor
The stepper motor is an open-loop control element that converts electrical pulse signals into angular displacement or linear displacement. In the case of non...[Details]
This week, Microsoft held its 2012 Microsoft Worldwide Partner Conference (WPC) in Toronto, Canada. At the conference, Microsoft showed its new products and services to partners around the world. A...[Details]
On the afternoon of July 10, Beijing time, Taiwan's largest chip designer MediaTek expects its smartphone chip shipments to grow by double digits in the third quarter of this year, and the company is ...[Details]
0 Introduction
With the rise and continuous improvement of the solid-state lighting industry, light-emitting diodes (LEDs) have become an alternative lighting technology and are gr...[Details]
VP2188 is a color STN LCD module produced by Jingdian Pengyuan. This module is a dot matrix transmissive color STN display screen with a color scale of 65 k colors and white LED backlight. Its core...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
京公网安备 11010802033920号
EEWORLD
