4-147107-0 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > The connector> The connector> 4-147107-0

4-147107-0: DescriptionHEADER CONNECTOR,PCB MNT,PLUG,80 CONTACTS,SKT,0.1 PITCH,SURFACE MOUNT TERMINAL,BLACK; CategoryThe connector The connector; File Size502KB，13 Pages; ManufacturerTE Connectivity; Websitehttp://www.te.com

Download Datasheet Parametric View All

4-147107-0 Overview

HEADER CONNECTOR,PCB MNT,PLUG,80 CONTACTS,SKT,0.1 PITCH,SURFACE MOUNT TERMINAL,BLACK

4-147107-0 Parametric

Parameter Name	Attribute value
Reach Compliance Code	unknown
body width	0.22 inch
subject depth	0.26 inch
body length	4.3 inch
Body/casing type	PLUG
Connector type	BOARD CONNECTOR
Contact to complete cooperation	SN-PB ON NI
Contact completed and terminated	TIN/LEAD OVER NICKEL
Contact point gender	FEMALE
Contact material	PHOSPHOR BRONZE
contact mode	RECTANGULAR
Contact resistance	12 mΩ
Contact style	SQ PIN-SKT
Dielectric withstand voltage	750VAC V
Durability	75 Cycles
maximum insertion force	2.502 N
Insulation resistance	5000000000 Ω
Insulator color	BLACK
insulator material	THERMOPLASTIC
Manufacturer's serial number	147107
Plug contact pitch	0.1 inch
Match contact row spacing	0.1 inch
Installation method	STRAIGHT BOTTOM MOUNT
Installation type	BOARD
Number of connectors	ONE
PCB row number	2
Number of rows loaded	2
Maximum operating temperature	125 °C
Minimum operating temperature	-65 °C
PCB contact pattern	RECTANGULAR
PCB contact row spacing	6.35 mm
Plating thickness	100u inch
Rated current (signal)	3 A
Guideline	UL, CSA
reliability	COMMERCIAL
Terminal pitch	2.54 mm
Termination type	SURFACE MOUNT
Total number of contacts	80
Evacuation force-minimum value	.417 N
Base Number Matches	1

Preview

Download Datasheet

View All

AMPMODU*

Mod II and Mod IV Printed

Circuit Board Connectors

Application Specification

114-25018

19 MAY 08

Rev E

NOTE

All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters. Unless

otherwise specified, dimensions have a tolerance of +0.13 and angles have a tolerance of +2 . Figures and

illustrations are for identification only and are not drawn to scale.

1. INTRODUCTION

This specification covers the requirements for application of AMPMODU Mod II and Mod IV Printed Circuit

(PC) Board Connectors for through hole and Surface Mount Technology (SMT). The connectors are available

with double beam receptacle contacts designed to accept 0.64 mm square posts. There are connectors in 2

through 80 positions for top and bottom entry applications as well as pass through applications with 2.54 mm

contact centerline spacing. All side entry connectors are available in 4 through 130 positions for double rows

and 2 through 65 positions for single row. The double beam contact connectors are available with single and

double rows of contacts. There are various solder lead configurations to meet a variety of system

requirements.

There are surface mount connectors available with and without hold–downs. The hold–downs help position the

connector on the pc board and hold it in place during soldering. Through hole connectors are available with and

without retentive contact leads. The retentive contact leads help stabilize and hold the connector in place

during soldering. Connectors without hold–down or retentive contact lead stabilizing features are available to

accommodate alternate system requirements.

When corresponding with Tyco Electronics Personnel, use the terminology provided on this specification to

help facilitate your inquiry for information. Basic terms and features of components are provided in Figure 1.

Double Beam Contact

Connectors (Typ)

Double Row

Connector

Single Row

Dual Entry

Connector

Mating

Face

Double Row

Connector

Dual

Entry

Right-Angle

Horizontal

Top Entry

Contact

Cavity

Connector

Dual Entry

Right-Angle Surface

Mount (Horizontal)

Single Row

Connector

Figure 1

2008 Tyco Electronics Corporation, Harrisburg, PA

TOOLING ASSISTANCE CENTER 1-800-722-1111

PRODUCT INFORMATION 1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at

www.tycoelectronics.com

of 13

LOC B

All International Rights Reserved

TE logo and Tyco Electronics are trademarks.

*Trademark. Other products, logos, and company names used are the property of their respective owners.

AMPMODU Mod II and Mod IV PC Board Connectors

2. REFERENCE MATERIAL

2.1. Revision Summary

114-25018

This paragraph is reserved for a revision summary of changes and additions made to this specification. The

following changes have been made to this revision.

Updated document to corporate requirements

New format

2.2. Customer Assistance

Reference Part Number 534998 and Product Code 5008 are representative numbers of AMPMODU PC Board

Connectors. Use of these numbers will identify the product line and expedite your inquiries through a service

network established to help you obtain product information. Such information can be obtained through a local

Tyco Electronics Representative or, after purchase, by calling the Tooling Assistance Center or the Product

Information Center number at the bottom of page 1.

2.3. Drawings

Customer drawings for each connector are available from the service network. The information contained in

customer drawings takes priority if there is a conflict with this specification or with any technical documentation

supplied by Tyco Electronics.

2.4. Manuals

Manual 402–40 is available upon request and can be used as a guide in soldering. This manual provides

information on various flux types and characteristics along with the commercial designation and flux removal

procedures. A checklist is included in the manual as a guide for information on soldering problems.

2.5. Specifications

Product Specifications provide product performance requirements and test information. See Product

Specifications 108–25022 and 108–25026 for double beam contacts.

3. REQUIREMENTS

3.1. Storage

A. Ultraviolet Light

Prolonged exposure to ultraviolet light may deteriorate the chemical composition used in the connector

housing material.

B. Shelf Life

The connectors should remain in the shipping containers until ready for use to prevent deformation of the

contact solder leads or other damage to the connectors. The connectors should be used on a first in, first

out basis to avoid storage contamination.

C. Chemical Exposure

Do not store connectors near any chemical listed below as they may cause stress, corrosion, cracks in the

contacts.

Alkalies

Amines

Ammonia

Carbonates

Citrates

Nitrites

Phosphates Citrates

Sulfur Nitrites

Sulfur Compounds

Tartrates

3.2. Special Characteristics

AMPMODU PC Board Connectors with double beam contacts have an operating temperature range of –65

to 105

C [–85

F to 221

F], and the connectors consist of a black polyester housing and phosphor bronze

contacts with one of two types of plating. The contact plating may be overall nickel with gold on the mating

surface and matte tin on the solder leads, or it may be overall nickel and matte tin plated.

2 of 13

Tyco Electronics Corporation

Rev E

Recommended Resources

Multiple input light sensors

High power tube power amplifier 01

Linear regulated power supply circuit diagram with excellent performance

Basic application circuit for VF conversion using LM311

555 linear voltage/frequency converter circuit (2)

Newbies are asking questions, please guide me: I have a 2410 board, but it cannot connect to the computer. Can you help me analyze the system? In addition to the driver, only 360 Security Guard is installed. The installation order of other softwar...; liu9952585 Embedded System

How to program STM8S products in the factory?: Hello everyone,our company is currently designing products based on STM8S103.I know that in the R&D stage, we can use the SWIM port of ST-LINK3 to burn STM8S103.But how to burn it in the factory or at...; lxl341222 stm32/stm8

can introductory book: CAN introductory book, for CAN bus beginners....; 匠人雷子 Renesas Electronics MCUs

How is PWM square wave converted into DC voltage through resistance and capacitance calculated?: How is the PWM square wave converted into DC voltage through resistance and capacitance calculated? Is it calculated through capacitive reactance: Xc=1/2πfc?...; 功夫崽崽 Analog electronics

MPC8315 startup problem: Has anyone used MPC8315? I want to use USB TAP to connect directly to nand, but I can't. I don't dare to clear the nor for the time being. Can this chip boot directly from nand? The bootloader is uboo...; evenles Embedded System

8 reasons that affect the accuracy of UWB positioning technology: The theoretical accuracy of UWB positioning technology can reach millimeter level or even micron level. However, when UWB positioning systems are deployed in actual scenarios, the positioning accuracy...; ohahaha RF/Wirelessly

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components