EEWORLDEEWORLDEEWORLD

Part Number

Search

BW2F-2R7JBW

Description
Fixed Resistor - Fusible, 2W, 2.7ohm, 5% +/-Tol, 200ppm/Cel, Through Hole Mount, AXIAL LEADED, ROHS COMPLIANT
CategoryPassive components    The resistor   
File Size65KB,1 Pages
ManufacturerRCD Components Inc.
Websitehttp://www.rcdcomponents.com/
Environmental Compliance
Download Datasheet Parametric View All

BW2F-2R7JBW Overview

Fixed Resistor - Fusible, 2W, 2.7ohm, 5% +/-Tol, 200ppm/Cel, Through Hole Mount, AXIAL LEADED, ROHS COMPLIANT

BW2F-2R7JBW Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid1733981426
package instructionAxial,
Reach Compliance Codecompliant
ECCN codeEAR99
YTEOL6.85
Other featuresFLAMEPROOF
structureFlameproof
JESD-609 codee3
Lead diameter0.8 mm
Lead length26 mm
Installation featuresTHROUGH HOLE MOUNT
Number of terminals2
Maximum operating temperature165 °C
Minimum operating temperature-55 °C
Package diameter4.1 mm
Package length11.4 mm
Package shapeTUBULAR PACKAGE
Package formAxial
method of packingBULK
Rated power dissipation(P)2 W
resistance2.7 Ω
Resistor typeFIXED RESISTOR - FUSIBLE
surface mountNO
technologyMETAL OXIDE FILM
Temperature Coefficient200 ppm/°C
Terminal surfaceMatte Tin (Sn)
Terminal shapeWIRE
Tolerance5%
Operating Voltage300 V

BW2F-2R7JBW Preview

FUSIBLE FILM RESISTORS,
GENERAL PURPOSE 1/8 WATT to 3 WATT
RESISTORS CAPACITORS COILS DELAY LINES
BW/MBW SERIES
RoHS
Term.W is
RoHS
compliant
& 260°C
compatible
BW Series - Axial Lead
MBW Series - SM MELF
Industry’s widest selection of fusible film resistors -
1/8W to 3W, .1Ω to 24KΩ, 1% to 5%, leaded & surface mount
Low cost, quick delivery (available on
SWIFT
TM
program)
Flameproof (UL94V0), surface-mount versions available
Low Cost Circuit Protection!
RCD pioneered fusible film resistors in the early 1970’s as a
low cost approach to circuit protection in case of overload or
component failure. The component is designed to act as a
conventional resistor under normal operating conditions, but
open quickly under fault conditions. Series BW meets the
requirements of EIA RS-325 and can be useful in eliminating
circuit board damage and fire hazards. Standard fusing
characteristics can be altered to customer requirements.
OPTIONS
Modified fusing characteristics (fast blow, slow blow, etc.)
Increased pulse capability (Option P)
Dozens of additional options are available...
Mil-spec screening/burn-in, special marking, non-standard
values, custom lead forming, increased power or voltage, etc.
Customized components are an RCD specialty!
H
→←
L
BW
D
d
A
MBW
Dimensions BW Series (Axial Lead)
RCD Type
BW1/8F
BW1/4F, MBW1/4F
BW1/2F, MBW1/2F
BW1/2FS, MBW1/2FS
BW1F, MBW1FS
BW2F, MBW2F
BW3F, MBW3F
1
Dimensions MBW (MELF)
H
(Min.)
A
± .012[.3]
B
(Max.)
N/A
.118 [3]
.118 [3]
.197 [5]
.040 [1]
.040 [1]
.080 [2]
.080 [2]
.154 [3.9] .060 [1.5]
.154 [3.9] .060 [1.5]
C
(Min.)
Wattage Resistance
Rating
1
Range
1
1/8W
1/4W
1/2W
1/2W
1.0W
2.0W
3.0W
2
Voltage
Rating
1, 2
200V
200V
250V
250V
300V
300V
350V
L
± .032 [.8]
.145 [3.7]
.250 [6.4]
.354 [9.0]
.250 [6.4]
.375 [9.5]
.450 [11.4]
1/2
D
± .024 [.6]
.067 [1.7]
.090 [2.3]
.128 [3.3]
.090 [2.3]
.135 [3.4]
.162 [4.1]
d
±.003 [.07]
1Ω to 10K
0.1
to 10K
0.1
to 24K
0.2
to 20K
0.1
to 24K
0.1
to 24K
0.1
to 24K
.020 [.5] 1.00 [25]
.022 [.55] 1.02 [26] .256 [6.5]
.025 [.6] 1.02 [26] .374 [9.5]
.022 [.55] 1.02 [26] .256 [6.5]
.026 [.65] 1.02 [26] .374 [9.5]
.031[.8]
.031[.8]
1.02 [26] .441[ 11.2]
.60±.062[15.2±1.6] .22±.032[5.6±.8]
1.37 [35] .598 [15.2] .220 [5.6]
Expanded range available
Maximum working voltage is determined by E = (PR) , E should not exceed value listed.
FUSING CHARACTERISTICS
FUSING TIME (SECONDS, TYP.)
60
50
40
1/2F, FS
1F, 1FS
30
1/8F
2F
10
0
5
10
15
20
30
40
50
60
80
100
APPLIED POWER (WATTS)
APPLICATION NOTES:
1. Fault level must be suitable to safely open the resistor quickly, especially surface mount
MBW models. If insufficent, the resistor may reach elevated temp. For this reason, the
fusing overload must be relatively large compared to rated W, 20 to 50x is common for
most axial-lead applications, 40 to 100x for most SM circuits. SM fusing times vary due to
mounting geometry/materials, so each application needs to be evaluated by user. The fault
condition must be at least equal to the minimum W indicated in each of the above curves,
and preferably double for SM applications. Fusing may still occur at W levels below the
levels graphed above but not consistently (fast-blow models available). Don’t exceed volt
rating or 200x W rating, whichever is less (increased levels available).
2. For customized models, complete RCD’s Fuse Questionnaire or advise the desired fusing
wattage or current, min.& max. blow time, continuous wattage, ambient temp., pulse
conditions, physical constraints, voltage to be interrupted, frequency, etc.
3. Maintain clearance from any heat-sensitive or flammable materials.
4. Fusing times vary depending on resistance value. Typical fusing times are given above
for 1Ω - 3.9K. Low values tend to fuse slower. Consult factory for assistance.
5. Residual resis. is
≥50x
initial value after fusing at 20x rated W (30x for BW1/8F & MBW)
6. Verify selection by evaluating under the full range of fault conditions. Place resistors
inside a protective case when testing.
TYPICAL PERFORMANCE
Temperature Coefficient
Load Life Stability
Operating Temp. Range
Power Derating
Dielectric Strength
200ppm/°C
5%
-55 to +165°C
0.71%/°C >25°C
500V (300V BW1/8F)
P/N DESIGNATION:
BW1F
RCD Type
Options
(leave blank if standard)
3F
20
1/4F
Inch [mm]
B
C
- 101 J T W
Resis.Code 1%:
3 signif. figures & multiplier,
(R100=.1Ω,1R00=1Ω,10R0=10Ω,1000=100Ω, etc.)
Resis.Code 2%-10%:
2 signif. figures & multiplier,
(R10=0.1Ω, 1R0=1Ω, 100=10Ω, 101=100Ω, etc.)
Tolerance:
J=5% (std.) G=2%, F=1%
Packaging:
B=Bulk, T=Tape & Reel
Termination:
W = Lead-free, Q = Tin/Lead
(leave blank if either acceptable)
RCD Components Inc,
520 E.Industrial Park Dr, Manchester, NH, USA 03109
rcdcomponents.com
Tel: 603
-
669
-
0054 Fax: 603
-
669
-
5455 Email:sales@rcdcomponents.com
FA037D Sale of this product is in accordance with GF-061. Specifications subject to change without notice.
81
Two FPGAs connected sequentially?
How should I connect two FPGAs in sequence? Which pins do I need to connect? Please help!...
woshiwwa FPGA/CPLD
Experience the power of ARM Compiler 6 (MDK 5.22)
[i=s] Last edited by ketose on 2016-11-18 17:16 [/i] With the launch of Cortex-M23 and Cortex-M33 cores, ARM's MDK has been upgraded. I also caught up with this version and downloaded it for trial use...
ketose MCU
Help with the design of AD9854 signal generator based on FPGA
The design of arbitrary waveform generator has been selected for electronic competitions many times, but I am confused when I change it to AD9854. I hope someone can give me some advice. Thank you....
留一片空白 FPGA/CPLD
Does anyone use FFT?
Has anyone used FFT? I also want to make a music display, but I don't know how to do FFT....
liushiming82 51mcu
How to Select and Integrate MEMS Motion Processing Solutions in Consumer Electronics Devices
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 20:02[/i] Motion processing, which measures and intelligently processes the motion of a device in three-dimensional space, will be the nex...
zhuxl Mobile and portable
Lesson 3: How to become a qualified electronic engineer?
在网络上很多初学者在问:怎样成为一个合格的电子工程师? 我谈谈自己的看法吧…… 第一步 入门-51核心和基本电路 中国人有13亿啊,每年有多少大学生毕业呢?我不知道。 但是我看到有一张照片,招聘会上熙熙攘攘,人来人往,十分震撼。从来没有一个时刻让我感觉到中国的人力资源是如此的丰富。但是,从现在的大学毕业出来的学生学到了什么东西呢?一些理论,跟实际脱钩的理论。有没有用呢?有点用。但是,在企业中,需要...
fjes MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1939  1312  2923  2537  704  40  27  59  52  15 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号