PA-1001A1PSC3Y datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > PA-1001A1PSC3Y

Preview

PA-1001A1PSC3Y: DescriptionSIGNAL CONDITIONER & CONVERTERS; File Size185KB，11 Pages; ManufacturerETC

Download Datasheet View All

PA-1001A1PSC3Y Overview

SIGNAL CONDITIONER & CONVERTERS

Preview

Download Datasheet

View All

INSTALATION, OPERATION & MAINTENANCE

MANUAL

FOR

PA-1001A Series

SIGNAL CONDITIONER

& CONVERTORS

PA1001A – 7/02

Page 1 of 11

ENVIRONMENTAL:

•

OPERATING:

STORAGE:

-40°C TO 85°C

-40°C TO 150°C

ENCLOSURES:

•

Unit is intended for mounting in a conduit box and comes with 2 ½” on center mounting holes. An

optional explosion proof or NEMA-4x enclosure is available upon request.

APPROVALS:

•

EN50081-1:1992 Generic Emission Standard

•

EN50082-2:1995 Generic Immunity Requirements

•

CE compliant to EMC Directive 89/336/EECfor uses in residential, commercial, light or heavy

industrial environments.

INSTALLATION AND WIRING DETAILS:

In considering the interconnections between the PA1001A and the measurement system some

attention must be given to anticipated noise sources and to the coupling of these noise sources to the

interconnecting wiring.

Noise signals may be coupled into the wiring between the pickup coil, the PA1001A, and the

electronic measuring systems. In general, utilizing a shielded, twisted pair for the interconnection

greatly reduces this coupling. The shield should be grounded on both ends of the cable.

However, even with proper interconnecting cabling, cross talk with other signal lines or power lines

may still occur and should be avoided. Physical isolation of the wiring reduces the chance of

potential problems.

The pickup coil should not be located more than 100 feet from the PA1001A preamplifier. It is

recommended that the PA1001A be installed on or near the pickup coil to assure optimum

performance.

INSTALLATION:

The Model PA1001A should be placed in a convenient location that maintains access to the unit

should repairs or readjustment is required.

Connections to the terminal block should be carefully dressed to avoid having bare wires extend pass

the screw clamp on the terminal block. This is particularly important when the PC card is mounted

within an explosion proof enclosure. Wires should be neatly dressed near bottom of enclosure to

prevent problems when cover is installed.

For compliance with EMI/RFI requirements the pre-amplifier must be installed in a metal enclosure

such as a suitable NEMA 4 (e.g. GUAC) junction box. The enclosure must be properly grounded.

Also a grounding strap is required from the enclosure to the power supply common (pin 7).

The cable entry requires 360° grounding coverage to the enclosure case. This is obtained by using

twisted pair with full braid cable and a cable fitting that provides a metal to metal cable clamping

connection. The insulation of the cables should be stripped back to allow for connection to the

terminal block and allow for the cable fitting to clamp onto the braided shield. Any open areas should

then be covered using foil tape.

In hazardous locations where metal conduit is used, 360° grounding are achieved. All cable shields

should be terminated to the enclosure-grounding stud.

PA1001A – 7/02

Page 4 of 11

Recommended Resources

Voltage Controlled ECL (Emitter Coupled Logic) Integrated Circuit Crystal Oscillator Generator Circuit

Diamond Differential Circuit

Transceiver relay circuit

TDA2611A power amplifier circuit

Overvoltage or undervoltage action circuit

555 infrared remote control fan speed switch circuit

Analyzing the Bluetooth and MSP430 Audio Sink Reference Design: [i=s]This post was last edited by 灞波儿奔 on 2017-3-15 22:45[/i] [p=30, null, left]TI's Bluetooth + MSP430 audio heat sink reference design can be used by customers to create a variety of low-end, low-po...; 灞波儿奔 Microcontroller MCU

I want a cc2530 temperature acquisition program, the simplest one will do: I'm stuck at this point now, there is no procedure, no reference, the simplest one will do, please help me...; q137226446 RF/Wirelessly

MSP430F1611 Learning: [color=rgb(51, 51, 51)][font="]/* Drive capability of MSP430 I/O port*/[/font][/color] [color=rgb(51, 51, 51)][font="]The maximum output or absorption current of each I/O port is 6mA[/font][/color] [c...; fish001 Microcontroller MCU

Friendly Arm dedicated serial communication tool DNW: :lol :hug:...; moonwolf526 Embedded System

How should the DCDC on the board be laid out?: In PCB design, the design of the power supply part is a more difficult and more important part. Generally, power chip manufacturers will recommend some layouts. The power supply layout principles I kn...; buildele Power technology

The entrance hall of C++ learning---console application: The entrance hall of C++ learning --- console application //The gorgeous stage of WIN program development has attracted countless people with empty hands. In the excitement, it is easy to forget that ...; geyin Embedded System

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components