P89LPC930/931
8-bit microcontrollers with two-clock 80C51 core
4 kB/8 kB 3 V Flash with 256-byte data RAM
Rev. 05 — 15 December 2004
Product data
1. General description
The P89LPC930/931 are single-chip microcontrollers designed for applications
demanding high-integration, low cost solutions over a wide range of performance
requirements. The P89LPC930/931 is based on a high performance processor
architecture that executes instructions in two to four clocks, six times the rate of
standard 80C51 devices. Many system-level functions have been incorporated into
the P89LPC930/931 in order to reduce component count, board space, and system
cost.
2. Features
s
A high performance 80C51 CPU provides instruction cycle times of 111 ns to
222 ns for all instructions except multiply and divide when executing at 18 MHz.
This is 6 times the performance of the standard 80C51 running at the same clock
frequency. A lower clock frequency for the same performance results in power
savings and reduced EMI.
s
2.4 V to 3.6 V V
DD
operating range. I/O pins are 5 V tolerant (may be pulled up or
driven to 5.5 V).
s
4 kB/8 kB Flash code memory with 1 kB sectors, and 64-byte page size.
s
Byte-erase allowing code memory to be used for data storage.
s
Flash program operation completes in 2 ms.
s
Flash erase operation completes in 2 ms.
s
256-byte RAM data memory.
s
Two 16-bit counter/timers. Each timer may be configured to toggle a port output
upon timer overflow or to become a PWM output.
s
Real-Time clock that can also be used as a system timer.
s
Two analog comparators with selectable inputs and reference source.
s
Enhanced UART with fractional baud rate generator, break detect, framing error
detection, automatic address detection and versatile interrupt capabilities.
s
400 kHz byte-wide I
2
C-bus communication port.
s
SPI communication port.
s
Eight keypad interrupt inputs, plus two additional external interrupt inputs.
s
Four interrupt priority levels.
s
Watchdog timer with separate on-chip oscillator, requiring no external
components. The Watchdog time-out time is selectable from 8 values.
s
Active-LOW reset. On-chip power-on reset allows operation without external reset
components. A reset counter and reset glitch suppression circuitry prevent
spurious and incomplete resets. A software reset function is also available.
Philips Semiconductors
P89LPC930/931
8-bit microcontrollers with two-clock 80C51 core
s
Low voltage reset (Brownout detect) allows a graceful system shutdown when
power fails. May optionally be configured as an interrupt.
s
Oscillator Fail Detect. The watchdog timer has a separate fully on-chip oscillator
allowing it to perform an oscillator fail detect function.
s
Configurable on-chip oscillator with frequency range and RC oscillator options
(selected by user programmed Flash configuration bits). The RC oscillator (factory
calibrated to
±1
%) option allows operation without external oscillator
components. Oscillator options support frequencies from 20 kHz to the maximum
operating frequency of 18 MHz. The RC oscillator option is selectable and fine
tunable.
s
Programmable port output configuration options:
x
Quasi-bidirectional
x
Open drain
x
Push-pull
x
Input-only
s
Port ‘input pattern match’ detect. Port 0 may generate an interrupt when the value
of the pins match or do not match a programmable pattern.
s
Second data pointer.
s
Schmitt trigger port inputs.
s
LED drive capability (20 mA) on all port pins. Maximum combined I/O current of
100 mA.
s
Controlled slew rate port outputs to reduce EMI. Outputs have approximately
10 ns minimum ramp times.
s
23 I/O pins minimum (28-pin package). Up to 26 I/O pins while using on-chip
oscillator and reset options.
s
Only power and ground connections are required to operate the P89LPC930/931
using on-chip oscillator and on-chip reset options.
s
Serial Flash programming allows in-circuit production coding. Flash security bits
prevent reading of sensitive programs.
s
In-Application Programming of the Flash code memory. This allows changing the
code in a running application.
s
Idle and two different Power-down reduced power modes. Improved wake-up from
Power-down mode (a low interrupt input starts execution). Typical Power-down
current is 1
µA
(total Power-down with voltage comparators disabled).
s
28-pin TSSOP package.
s
Emulation support.
9397 750 14472
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 05 — 15 December 2004
2 of 55
Philips Semiconductors
P89LPC930/931
8-bit microcontrollers with two-clock 80C51 core
3. Ordering information
Table 1:
Ordering information
Package
Name
P89LPC930FDH
P89LPC931FDH
TSSOP28
TSSOP28
Description
plastic thin shrink small outline package;
28 leads; body width 4.4 mm
plastic thin shrink small outline package;
28 leads; body width 4.4 mm
Version
SOT361-1
SOT361-1
Type number
3.1 Ordering options
Table 2:
Part options
Program memory
4 kB
8 kB
Temperature range
−45 °C
to +85
°C
−45 °C
to +85
°C
Frequency
0 MHz to 18 MHz
0 MHz to 18 MHz
Type number
P89LPC930FDH
P89LPC931FDH
9397 750 14472
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 05 — 15 December 2004
3 of 55
Philips Semiconductors
P89LPC930/931
8-bit microcontrollers with two-clock 80C51 core
4. Block diagram
HIGH PERFORMANCE
ACCELERATED 2-CLOCK 80C51 CPU
4 kB/8 kB
CODE FLASH
INTERNAL BUS
256-BYTE
DATA RAM
PORT 3
CONFIGURABLE I/Os
PORT 2
CONFIGURABLE I/Os
PORT 1
CONFIGURABLE I/Os
PORT 0
CONFIGURABLE I/Os
UART
I
2
C
SPI
REAL-TIME CLOCK/
SYSTEM TIMER
TIMER 0
TIMER 1
WATCHDOG TIMER
AND OSCILLATOR
KEYPAD
INTERRUPT
ANALOG
COMPARATORS
PROGRAMMABLE
OSCILLATOR DIVIDER
CPU
CLOCK
ON-CHIP
RC
OSCILLATOR
CRYSTAL
OR
RESONATOR
CONFIGURABLE
OSCILLATOR
POWER MONITOR
(POWER-ON RESET,
BROWNOUT RESET)
002aaa428
Fig 1. Block diagram.
9397 750 14472
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 05 — 15 December 2004
4 of 55
Philips Semiconductors
P89LPC930/931
8-bit microcontrollers with two-clock 80C51 core
5. Pinning information
5.1 Pinning
handbook, halfpage
P2.0
P2.1
KBIO/CMP2/P0.0
P1.7
P1.6
RST/P1.5
VSS
XTAL1/P3.1
CLKOUT/XTAL2/P3.0
1
2
3
4
5
28 P2.7
27 P2.6
26 P0.1/CIN2B/KBI1
25 P0.2/CIN2A/KBI2
24 P0.3/CIN1B/KBI3
P89LPC930FDH
P89LPC931FDH
002aaa429
6
7
8
9
23 P0.4/CIN1A/KBI4
22 P0.5/CMPREF/KBI5
21 VDD
20 P0.6/CMP1/KBI6
19 P0.7/T1/KBI7
18 P1.0/TXD
17 P1.1/RXD
16 P2.5/SPICLK
15 P2.4/SS
INT1/P1.4 10
SDA/INT0/P1.3 11
SCL/T0/P1.2 12
MOSI/P2.2 13
MISO/P2.3 14
Fig 2. DIP28 pin configuration.
9397 750 14472
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data
Rev. 05 — 15 December 2004
5 of 55
京公网安备 11010802033920号
EEWORLD
