177-710-5-15GP0J1-24SDN datasheet, PDF

Datasheet> All Categories > The connector> The connector> 177-710-5-15GP0J1-24SDN

177-710-5-15GP0J1-24SDN: DescriptionInterconnection Device; CategoryThe connector The connector; File Size436KB，4 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/; Environmental Compliance

Download Datasheet Parametric View All

177-710-5-15GP0J1-24SDN Overview

Interconnection Device

177-710-5-15GP0J1-24SDN Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Reach Compliance Code	compli
Connector type	INTERCONNECTION DEVICE
Base Number Matches	1

Preview

Download Datasheet

View All

MWDM Micro-D Shielded Cable Assemblies

Single-Ended or Double-Ended–These

easy-to-order cable

assemblies eliminate the need for expensive assembly

labor. 100% tested and ready for use.

Now With Twisted Pairs–No

need to create a procurement

speciﬁcation for Micro-D cables with twisted pairs. Glenair

177-740 cables are furnished with a full complement of

white/blue twisted pair wires.

Integral Shield Termination–The

connector shell has a

platform to accept Band-It shield termination bands. The

cable shield braid is attached directly to the connector.

Save Labor, Reduce Weight and Improve EMI Shielding with

Glenair’s Micro-D Shielded Cable Assemblies

Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s fully

shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-piece connector

shell and secured with a stainless steel

BAND-IT

® clamp. These pre-wired, 100% tested assemblies meet the

requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low shell-to-shell resistance.

Available with a variety of wire types and shields, Micro-D shielded assemblies can be ordered in any length, either

single-ended or “back-to-back”.

Ground Spring and EMI Shielding Effectiveness

– A gold-plated

stainless steel ground spring on the pin connector mating face offers

substantial improvement in EMI protection. The graphs compare

identical connectors tested with and without ground springs.

EMI Performance with Ground Spring

SHIELDING EFFECTIVENESS (DB)

100

1.00E+03

100

1.00E+03

EMI Performance without Ground Spring

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

FREQUENCY (Hz)

CAGE Code 06324/0CA77

Printed in U.S.A.

GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912

www.glenair.com

B-8

E-Mail: sales@glenair.com

Recommended Resources

Resistance furnace thyristor temperature control circuit 2

Three working states of the transistor - NPN type - cut-off state

Homemade current negative feedback electronic frequency dividing power amplifier 01

HT-6030/HT-6034 circuit-a

Light control switch circuit

555 three-digit display capacitance meter circuit

ADuc7026 Learning-I/O: [i=s] This post was last edited by dj狂人 on 2015-1-8 16:31 [/i] Before we start to talk about how to operate the I/O of ADuc7026, let's talk about the things we need to pay attention to in programming....; dj狂人 ADI Reference Circuit

Is anyone doing data collection?: I am using FPGA for data acquisition. The specific idea is as follows: The front-end analog signal enters low-pass filtering, then converts single-ended to differential, and then sends it to 12bit/80M...; cuianbin FPGA/CPLD

I have questions about FIFO delay and shift register, please give me some advice!: My supervisor assigned me a project, and I was responsible for the following: On the ore conveyor belt, a linear CCD was used to record the size of the ore. The output signal was output through a seri...; shenqizhiren FPGA/CPLD

Graduation project based on zigbee: My graduation project is a flower watering system based on zigbee. I just bought two zigbee modules, but I still don’t know where to start. Could you please give me some advice?...; vollyKing RF/Wirelessly

[Digging Power Supply] LED T8 Tube Driver Power Supply: This is an isolated driver power supply for 12 series and 24 parallel load lamp beads. Its basic parameters are as follows:Input voltage: AC90-305V 50/60Hz Output voltage: DC25-45V Output current: 415...; dongguanze Analogue and Mixed Signal

Who knows how to use CMU200? I want to learn: Hey, experts, I want to learn CMU200 but I don't know how to learn it. Can you tell me?...; 272258198 Test/Measurement

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components