INTEGRATED CIRCUITS
83C750/87C750
80C51 8-bit microcontroller family
1K/64 OTP ROM, low pin count
Product specification
Supersedes data of 1998 Jan 19
IC20 Data Handbook
1998 May 01
Philips
Semiconductors
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family
1K/64 OTP/ROM, low pin count
83C750/87C750
DESCRIPTION
The Philips 8XC750 offers the advantages of the 80C51 architecture
in a small package and at low cost.
The 8XC750 Microcontroller is fabricated with Philips high-density
CMOS technology. Philips epitaxial substrate minimizes CMOS
latch-up sensitivity.
The 87C750 contains a 1k
×
8 EPROM, a 64
×
8 RAM, 19 I/O lines,
a 16-bit auto-reload counter/timer, a five-source, fixed-priority level
interrupt structure and an on-chip oscillator.
PIN CONFIGURATIONS
P3.4/A4 1
P3.3/A3 2
P3.2/A2/A10 3
P3.1/A1/A9 4
P3.0/A0/A8 5
P0.2/V
PP
6
P0.1/OE–PGM
P0.0/ASEL
RST
7
8
9
PLASTIC
DUAL
IN-LINE
AND
SHRINK
SMALL
OUTLINE
PACKAGE
24 V
CC
23 P3.5/A5
22 P3.6/A6
21 P3.7/A7
20 P1.7/T0/D7
19 P1.6/INT1/D6
18 P1.5/INT0/D5
17 P1.4/D4
16 P1.3/D3
15 P1.2/D2
14 P1.1/D1
13 P1.0/D0
FEATURES
•
80C51 based architecture
•
Oscillator frequency range—up to 16MHz
•
Small package sizes
–
24-pin DIP (300 mil “skinny DIP”)
–
24-pin Shrink Small Outline Package
–
28-pin PLCC
X2 10
X1 11
V
SS
12
4
5
PLASTIC
LEADED
CHIP
CARRIER
11
12
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Function
P3.4/A4
P3.3/A3
P3.2/A2/A10
P3.1/A1/A9
NC*
P3.0/A0/A8
P0.2/V
PP
P0.1/OE-PGM
P0.0/ASEL
NC*
RST
X2
X1
V
SS
18
Pin
15
16
17
18
19
20
21
22
23
24
25
26
27
28
1
26
•
87C750 available in one-time programmable plastic packages
•
Low power consumption:
–
Normal operation: less than 11mA @ 5V, 12MHz
–
Idle mode
–
Power-down mode
25
19
•
1k
×
8 EPROM (87C750)
•
64
×
8 RAM
•
16-bit auto reloadable counter/timer
•
Boolean processor
•
CMOS and TTL compatible
•
Well suited for logic replacement, consumer and industrial
applications
•
LED drive outputs
Function
P1.0/D0
P1.1/D1
P1.2/D2
P1.3/D3
P1.4/D4
P1.5/INT0/D5
NC*
NC*
P1.6/INT1/D6
P1.7/T0/D7
P3.7/A7
P3.6/A6
P3.5/A5
V
CC
* NO INTERNAL CONNECTION
SU00295A
ORDERING INFORMATION
ROM
P83C750EBP N
P83C750EFP N
P83C750EBA A
P83C750EFA A
EPROM
1
P87C750EBP N
P87C750EFP N
P87C750EBA A
P87C750EFA A
OTP
OTP
OTP
OTP
TEMPERATURE RANGE
°C
AND PACKAGE
0 to +70, Plastic Dual In-line Package
–40 to +85, Plastic Dual In-line Package
0 to +70, Plastic Lead Chip Carrier
–40 to +85, Plastic Lead Chip Carrier
0 to +70, Shrink Small Outline Package
FREQUENCY
3.5 to 16MHz
3.5 to 16MHz
3.5 to 16MHz
3.5 to 16MHz
3.5 to 16MHz
DRAWING
NUMBER
SOT222-1
SOT222-1
SOT261-3
SOT261-3
SOT340-1
P83C750EBD DB
P87C750EBD DB
OTP
NOTE:
1. OTP = One Time Programmable EPROM.
1998 May 01
2
853–1683 19331
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family
1K/64 OTP/ROM, low pin count
83C750/87C750
BLOCK DIAGRAM
P0.0–P0.2
PORT 0
DRIVERS
V
CC
V
SS
RAM ADDR
REGISTER
RAM
PORT 0
LATCH
EPROM
B
REGISTER
ACC
STACK
POINTER
PROGRAM
ADDRESS
REGISTER
TMP2
TMP1
ALU
PCON
IE
TH0
TL0
RTL
RTH
TCON
BUFFER
PSW
INTERRUPT AND
TIMER BLOCKS
PC
INCRE-
MENTER
PROGRAM
COUNTER
INSTRUCTION
REGISTER
RST
TIMING
AND
CONTROL
DPTR
PD
PORT 1
LATCH
PORT 3
LATCH
OSCILLATOR
PORT 1
DRIVERS
X1
X2
P1.0–P1.7
P3.0–P3.7
PORT 3
DRIVERS
SU00312
1998 May 01
3
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family
1K/64 OTP/ROM, low pin count
83C750/87C750
PIN DESCRIPTIONS
PIN NO.
MNEMONIC
V
SS
V
CC
P0.0-P0.2
DIP/
SSOP
12
24
8-6
LCC
14
28
9-7
TYPE
I
I
I/O
Circuit Ground Potential
Supply voltage during normal, idle, and power-down operation.
Port 0:
Port 0 is a 3-bit open-drain, bidirectional port. Port 0 pins that have 1s written to them float,
and in that state can be used as high-impedance inputs. These pins are driven low if the port register
bit is written with a 0. The state of the pin can always be read from the port register by the program.
P0.0, P0.1, and P0.2 are open drain bidirectional I/O pins with the electrical characteristics listed in
the tables that follow. While these differ from “standard TTL” characteristics, they are close enough
for the pins to still be used as general-purpose I/O. Port 0 also provides alternate functions for
programming the EPROM memory as follows:
V
PP
(P0.2) –
Programming voltage input. (See Note 1.)
OE/PGM (P0.1) –
Input which specifies verify mode (output enable) or the program mode.
OE/PGM = 1 output enabled (verify mode).
OE/PGM = 0 program mode.
ASEL (P0.0) –
Input which indicates which bits of the EPROM address are applied to port 3.
ASEL = 0 low address byte available on port 3.
ASEL = 1 high address byte available on port 3 (only the three least significant bits are used).
Port 1:
Port 1 is an 8-bit bidirectional I/O port with internal pull-ups. Port 1 pins that have 1s written
to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 1 pins
that are externally pulled low will source current because of the internal pull-ups. (See DC
Electrical Characteristics: I
IL
). Port 1 serves to output the addressed EPROM contents in the verify
mode and accepts as inputs the value to program into the selected address during the program
mode. Port 1 also serves the special function features of the 80C51 family as listed below:
INT0 (P1.5):
External interrupt.
INT1 (P1.6):
External interrupt.
T0 (P1.7):
Timer 0 external input.
Port 3:
Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that have 1s written
to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 3 pins
that are externally being pulled low will source current because of the pull-ups. (See DC Electrical
Characteristics: I
IL
). Port 3 also functions as the address input for the EPROM memory location to
be programmed (or verified). The 10-bit address is multiplexed into this port as specified by
P0.0/ASEL.
Reset:
A high on this pin for two machine cycles while the oscillator is running, resets the device.
An internal diffused resistor to V
SS
permits a power-on RESET using only an external capacitor to
V
CC
. After the device is reset, a 10-bit serial sequence, sent LSB first, applied to RESET, places
the device in the programming state allowing programming address, data and V
PP
to be applied for
programming or verification purposes. The RESET serial sequence must be synchronized with the
X1 input.
Crystal 1:
Input to the inverting oscillator amplifier and input to the internal clock generator circuits.
X1 also serves as the clock to strobe in a serial bit stream into RESET to place the device in the
programming state.
Crystal 2:
Output from the inverting oscillator amplifier.
NAME AND FUNCTION
6
7
7
8
N/A
I
8
9
I
P1.0-P1.7
13-20
15-20,
23, 24
I/O
18
19
20
P3.0-P3.7
5-1,
23-21
20
23
24
6, 4-1,
27-25
I
I
I
I/O
RST
9
11
I
X1
11
13
I
X2
10
12
O
NOTE:
1. When P0.2 is at or close to 0 Volt, it may affect the internal ROM operation. We recommend that P0.2 be tied to V
CC
via a small pull-up (e.g.,
2kΩ).
OSCILLATOR CHARACTERISTICS
X1 and X2 are the input and output, respectively, of an inverting
amplifier which can be configured for use as an on-chip oscillator.
To drive the device from an external clock source, X1 should be
driven while X2 is left unconnected. There are no requirements on
the duty cycle of the external clock signal, because the input to the
internal clock circuitry is through a divide-by-two flip-flop. However,
minimum and maximum high and low times specified in the data
sheet must be observed.
enough to allow the oscillator time to start up (normally a few
milliseconds) plus two machine cycles. At power-up, the voltage on
V
CC
and RST must come up at the same time for a proper start-up.
IDLE MODE
In idle mode, the CPU puts itself to sleep while all of the on-chip
peripherals stay active. The instruction to invoke the idle mode is the
last instruction executed in the normal operating mode before the
idle mode is activated. The CPU contents, the on-chip RAM, and all
of the special function registers remain intact during this mode. The
idle mode can be terminated either by any enabled interrupt (at
which time the process is picked up at the interrupt service routine
and continued), or by a hardware reset which starts the processor in
the same manner as a power-on reset.
RESET
A reset is accomplished by holding the RST pin high for at least two
machine cycles (24 oscillator periods), while the oscillator is running.
To insure a good power-up reset, the RST pin must be high long
1998 May 01
4
Philips Semiconductors
Product specification
80C51 8-bit microcontroller family
1K/64 OTP/ROM, low pin count
83C750/87C750
POWER-DOWN MODE
In the power-down mode, the oscillator is stopped and the
instruction to invoke power-down is the last instruction executed.
Only the contents of the on-chip RAM are preserved. A hardware
reset is the only way to terminate the power-down mode. the control
bits for the reduced power modes are in the special function register
PCON.
TCON is set on counter overflow and, if the interrupt is enabled, will
generate an interrupt.
TCON Register
MSB
GATE
C/T
TF
TR
IE0
IT0
IE1
LSB
IT1
GATE
Table 1.
MODE
Idle
Power-down
External Pin Status During Idle and
Power-Down Modes
Port 0
Data
Data
Port 1
Data
Data
Port 2
Data
Data
C/T
TF
TR
DIFFERENCES BETWEEN THE 8XC750 AND THE
80C51
Program Memory
On the 8XC750, program memory is 1024 bytes long and is not
externally expandable, so the 80C51 instructions MOVX, LJMP, and
LCALL are not implemented. The only fixed locations in program
memory are the addresses at which execution is taken up in
response to reset and interrupts, which are as follows:
Program Memory
Event
Address
Reset
000
External INT0
003
Counter/timer 0
00B
013
External INT1
IE0
IT0
IE1
IT1
1 – Timer/counter is enabled only when INT0 pin is high,
and TR is 1.
0 – Timer/counter is enabled when TR is 1.
1 – Counter/timer operation from T0 pin.
0 – Timer operation from internal clock.
1 – Set on overflow of TH.
0 – Cleared when processor vectors to interrupt routine
and by reset.
1 – Timer/counter enabled.
0 – Timer/counter disabled.
1 – Edge detected in INT0.
1 – INT0 is edge triggered.
0 – INT0 is level sensitive.
1 – Edge detected on INT1.
1 – INT1 is edge triggered.
0 – INT1 is level sensitive.
These flags are functionally identical to the corresponding 80C51
flags, except that there is only one timer on the 83C750 and the
flags are therefore combined into one register.
Note that the positions of the IE0/IT0 and IE1/IT1 bits are
transposed from the positions used in the standard 80C51 TCON
register.
Interrupt Subsystem – Fixed Priority
The IP register and the 2-level interrupt system of the 80C51 are
eliminated. Simultaneous interrupt conditions are resolved by a
single-level, fixed priority as follows:
Highest priority:
Pin INT0
Counter/timer flag 0
Pin INT1
Counter/Timer Subsystem
Timer/Counter
The 8XC750 has one timers: a 16-bit timer/counter. The 16-bit
timer/counter’s operation is similar to mode 2 operation on the
80C51, but is extended to 16 bits. The timer/counter is clocked by
either 1/12 the oscillator frequency or by transitions on the T0 pin.
The C/T pin in special function register TCON selects between
these two modes. When the TCON TR bit is set, the timer/counter is
enabled. Register pair TH and TL are incremented by the clock
source. When the register pair overflows, the register pair is
reloaded with the values in registers RTH and RTL. The value in the
reload registers is left unchanged. See the 83C750 counter/timer
block diagram in Figure 1. The TF bit in special function register
Special Function Register Addresses
Special function registers for the 8XC750 are identical to those of
the 80C51, except for the changes listed below:
80C51 special function registers not present in the 8XC750 are
TMOD (89), P2 (A0) and IP (B8). The 80C51 registers TH1 and TL1
are replaced with the 87C750 registers RTH and RTL respectively
(refer to Table 2).
OSC
÷
12
C/T = 0
TL
C/T = 1
TH
TF
Int.
T0 Pin
TR
Reload
Gate
INT0 Pin
RTL
RTH
SU00300
Figure 1.
83C751 Counter/Timer Block Diagram
1998 May 01
5
京公网安备 11010802033920号
EEWORLD
