EEWORLDEEWORLDEEWORLD

Part Number

Search

LG200M0680BP442250

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum, 200V, 20% +Tol, 20% -Tol, 680uF,
CategoryPassive components    capacitor   
File Size209KB,8 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance
Download Datasheet Parametric View All

LG200M0680BP442250 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum, 200V, 20% +Tol, 20% -Tol, 680uF,

LG200M0680BP442250 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid746284681
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
YTEOL0
capacitance680 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
diameter22 mm
dielectric materialsALUMINUM (WET)
length50 mm
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-25 °C
Package formSnap-in
method of packingBulk
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)200 V
ripple current1750 mA
YAGEO CORPORATION
ELECTROLYTIC CAPACITORS
Large Can Aluminum
Electrolytic Capacitors
LG
[ For General ]
For Printed Circuit Board High-Performance Aluminum Electrolytic Power Supply
Input and Output Filter Capacitors
ELECTRICAL CHARACTERISTICS
Operating Temperature Range -40 to +105°C
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
6.3 to 100VDC
560 ~ 82000µF
±20% at 120Hz, 20°C
I = 0.02CV, L = 20m/m, I = 0.03CV or 3mA whichever is smaller.
(After 5 Minutes Application of DC Working Voltage at 20°C)
I = Leakage Current (µA), C = Nominal Capacitance (µF),V = Rated Voltage (V)
Dissipation Factor (tanδ)
Rate Voltage (V)
D.F. (%)
Low Temperature Stability
Impedance Ratio (Max.)
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz)
6.3~100V
160~250V
315~450V
50
60
120 1K
10K
Endurance
0.88 0.90 1.00 1.15 1.16
0.85 0.88 1.00 1.15 1.20
0.88 0.90 1.00 1.10 1.15
6.3
60
10
55
16
55
25
45
35
35
50
30
63-100 160-400 450
25
15
20
-25 to +105°C
160 to 450VDC
47 ~ 2200µF
DESCRIPTION
Endurance : 105°C 2000 hours, higher temperature
than LH.
Ideally suitable for using in switching power supplies
and other industrial / commercial applications.
Measurement frequency: 120Hz
Rated Voltage (V)
Z(-25°C) / Z(20°C)
Z(-40°C) / Z(20°C)
6.3~16 25
4
15
3
10
35
3
8
50~63
2
6
80~10 160~400 450
2
5
4
-
8
-
After the rated voltage and rated ripple current have been applied at 105°C
for 2000 hours, the capacitors shall meet the following requirements.
(a)
Capacitance Change:
±20% of the Initial Value
(b)
Dissipation Factor:
200% of the Initial Specified Value
(c) Leakage Current:
the Initial Specified Value
Shelf Life
After having been placed at 105°C without voltage applied for 1000 hours,
the capacitors shall meet the same requirements as Endurance.
DIAGRAM OF DIMENSIONS
Location of P.C.B. Holes
Vinyl Sleeve
0.9
±
0.1
10
±
0.5
2mm x 2
3.0
0.8+0.2 /-0.1
Botton Plate
Negative
Unit: mm
10
±
0.5
5.8
±
1.0
1.5+0.2 /-0.1
Safety Device
L+2 Max.
5.8
±
0.1
D
±
1
MicroPython official website changed its logo
[font=Tahoma, Helvetica, SimSun, sans-serif]The previous logo was[/font][font=Tahoma, Helvetica, SimSun, sans-serif]Now it has been changed to the following. [/font]...
dcexpert MicroPython Open Source section
How to generate positive and negative 12V switching regulated power supply?
Can I use a commonly used DC-DC control chip (such as SG3525) to generate a positive and negative 12V power supply? Please give me some ideas!!...
LoHasMan Power technology
Chip Coin Sending Post (September 2nd to September 5th)
In order to participate in the competition, some friends often upload some existing materials on the forum, which causes great duplication of resources and affects the normal use of other friends. For...
soso Electronics Design Contest
LPC1768 IAP upgrade method
[size=4]1. Introduction to IAP [/size] [size=4]IAP is the abbreviation of "in applicatin programming", which means that the MCU can obtain new code in the system and reprogram itself, that is, change ...
Jacktang Microcontroller MCU
How to set the parameters of RC snubber circuit of mosfet switch tube in boost circuit
As the title says, in a boost circuit, the input voltage fluctuates between 12-18V, the output voltage is 24V, the output current is 2A, and the switching frequency is 50kHz. How should the RC buffer ...
大寒虫 Analog electronics
STM32 development data integration (data is constantly updated)
STM32 Getting Started Notes (I) [url=https://home.eeworld.com.cn/my/space.php?uid=42646&do=blog&id=12749]https://home.eeworld.com.cn/my/space.php?uid=42646&do=blog&id=12749[/url] SD card driver and LC...
亲善大使 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2794  2589  612  2115  2132  57  53  13  43  56 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号