Using the IDT CMOS Oscillator technology, originally developed by
Mobius Microsystems, the MM8202 replaces quartz crystal based
resonators and oscillators with a monolithic CMOS IC at the thinnest
possible form factors without the use of any mechanical frequency
source or PLL. The product is specially designed to work with the
next generation USB 2.0 High Speed, USB 2.0 Full/Low Speed and
USB-IC (USB-InterChip) interface controller ICs, and high density
SIM-, and smart-cards.
Features
• All-CMOS Temperature Compensated Oscillator
• TimeStak
TM
: Available in die form for the thinnest and smallest
MCP options (-D package option)
• Ultra-low power operation (2mA typical at 1.8V supply)
• No quartz or PLL used: very low jitter performance leading to low
link Bit Error Rates (BER)
• Excellent reliability: Shock and vibration resistant
• Many frequencies are supported
• Factory programmable from 6 to 133MHz
Ordering Information
8202
1
-
12
2
VP
3
C
4
NSG
5
6
T
7
Pin Assignment
1) IDT Base Part Number
2) FF: Factory Programmed Frequency in MHz
3) Supply Voltage Configuration
•
•
•
•
•
•
•
•
•
•
•
•
VP: 1.8V to 3.3V continuous operation
V: 3.3V only operation
T: 2.5V only operation
P: 1.8V only operation
C: CMOS Output
-D: Wafer form 200um thickness
-C: Wafer form 350um thickness
NSG: 5x3.2, 4-Pin Package
NVG: 2.5x2.0, 4-Pin Package
No
1
Name
CE
MM8202
4-pin NSG
5mm x 3.2mm x 0.9mm
Top View
CE
1
2
VSS
Bottom View
VDD
4
3
OUT
4) Output Signal Type
5) Package Options*
Table 1. Pin Descriptions
Type
Input
Pullup
Description
Chip Enable. Internal Pullup. MM8202 is
enabled when HIGH.When LOW, OUT has
a weak pull-down to GND internally
System Ground
Frequency Output
Power Supply. Use a 0.1µF decoupling
capacitor between VDD and VSS
6) Temperature Grade
“ “: 0 to 70 C Commercial Temperature Range i.e. default is blank
“ “: Shipped in Tube i.e. default is blank
T: Shipped in Tape & Reel
o
7) Tape & Reel Option
2
This product is rated “Green”. Please contact factory for environmental compliancy
information.
VSS
OUT
VDD
Power
Output
Power
3
4
The Preliminary Information presented herein represents a product in pre-production. The noted characteristics are based on initial product characterization and/or qualification.
Integrated Device Technology, Incorporated (IDT) reserves the right to change any circuitry or specifications without notice
may cause permanent damage to the device. These ratings are stress
specifications only. Functional operation of product at these conditions or any conditions beyond those listed in the
DC Characteristics
or
AC
Characteristics
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability.
Item
Supply Voltage, VDD
Input, V
I
(CE pin)
Output, V
O
(OUT pin)
Storage Temperature
4.6V
Rating
-0.5V to VDD + 0.5V
-0.5V to VDD + 0.5V
-65
o
C to 150
o
C
Electrical Characteristics
5
[3.3V]
VDD=3.0V to 3.6V, T
A
=0 to 70
o
C unless otherwise noted. Typical values are measured at VDD=3.3V, T
A
=35
o
C
Parameter
ElectroStaticDischa
rge
Supply Voltage
Input LOW level
Input HIGH level
Supply Current
Quiescent Current
Output LOW level
Output HIGH level
Output Frequency
Frequency Stability
Rise Time
Fall Time
Duty Cycle
Symbol
ESD
VDD
V
IL
V
IH
IDD
IDDQ
V
OL
V
OH
F
OUT
F
TOT
RT
FT
DC
Conditions
Human Body Model, tested per JESD D22-A114
Normal Operation
3
CE pin
CE pin
Active supply current, VDD=3.3V, T=35oC, no output load
CE=LOW, output disabled
I
OL
= -4mA
I
OH
= 4mA
Factory Programmable.Contact IDT for frequencies not listed
Total Frequency Stability over temperature,supply
variation,aging (1st year at 35oC),shock&vibration. “ ” device
option, over 0-70
o
C range
20% to 80% x VDD. Output load (C
L
) =8pF, NSG-option
80% to 20% x VDD. Output load (C
L
) =8pF, NSG-option
Clock output duty cycle. Measured under 80MHz, VDD/2,
C
L
=8pF
Clock output duty cycle. Measured over 80MHz, VDD/2,
C
L
=8pF
Output valid time after VDD meets the specified range&CE
transition
Total RMS Period Jitter (including random and
deterministic)
1,2
The absolute value of max change in the periods of any 2
adjacent cycles
1,2,4
1MHz offset from carrier
1,2
Min
4000
3.0
-0.3
VDD*0.7
Typ
Max
Units
V
3.3
2.5
0.2
VDD-0.5
6
3.6
VDD*0.3
VDD+0.3
3.0
1
0.5
133
+400
1.9
1.9
12,24,25,50
V
V
V
mA
µA
V
V
MHz
ppm
ns
ns
%
%
µs
ps
RMS
45
40
400
3.5
55
60
Power-up time
Period Jitter
Cycle-cycle Jitter
Phase Noise
t
on
PJ
RMS
CJ
PN
50
-140
-135
ps
dBc/Hz
Notes 1. Measured with a 50Ω to GND termination
2: Measured at 48MHz output frequency
3. The MM8202 will support continuous VDD operation from 1.62 to 3.6V. The device can be powered up with a supply voltage at any of the 3 main supply rails of 1.8V, 2.5V or 3.3V.
4. Measured over 1000 cycles per JEDEC standard 65
5. Electrical parameters are guaranteed over the specified ambient operating temperature range, which is established when the device is mounted in a test socket with maintained
transverse airflow greater than 500lfpm. The device will meet specifications after thermal equilibrium has been reached under these conditions.
C unless otherwise noted. Typical values are measured at VDD=2.5V, T
A
=35
o
C
Parameter
ElectroStaticDischa
rge
Supply Voltage
Input LOW level
Input HIGH level
Supply Current
Quiescent Current
Output LOW level
Output HIGH level
Output Frequency
Frequency Stability
Rise Time
Fall Time
Duty Cycle
Symbol
ESD
VDD
V
IL
V
IH
IDD
IDDQ
V
OL
V
OH
F
OUT
F
TOT
RT
FT
DC
Conditions
Human Body Model, tested per JESD D22-A114
Normal Operation
3
CE pin
CE pin
Active supply current, VDD=2.5V, T=35oC, no output load
CE=LOW, output disabled
I
OL
= -3mA
I
OH
= 3mA
Factory Programmable.Contact IDT for frequencies not listed
Total Frequency Stability over temperature,supply
variation,aging (1st year at 35oC),shock&vibration. “ ” device
option, over 0-70
o
C range
20% to 80% x VDD. Output load (C
L
) =7pF, NSG-option
80% to 20% x VDD. Output load (C
L
) =7pF, NSG-option
Clock output duty cycle. Measured under 100MHz at VDD/2,
C
L
=7pF
Clock output duty cycle. Measured over 100MHz at VDD/2,
C
L
=7pF
Output valid time after VDD meets the specified range&CE
transition
Total RMS Period Jitter (including random and
deterministic)
1,2
The absolute value of max change in the periods of any 2
adjacent cycles
1,2,4
1MHz offset from carrier
1,2
Min
4000
2.25
-0.3
VDD*0.7
Typ
Max
Units
V
2.5
2.25
0.2
VDD-0.4
6
2.75
VDD*0.3
VDD+0.3
2.75
1
0.4
133
+400
2.3
2.3
12,24,25,50
V
V
V
mA
µA
V
V
MHz
ppm
ns
ns
%
%
µs
ps
RMS
45
40
400
3.5
55
60
Power-up time
Period Jitter
Cycle-cycle Jitter
Phase Noise
t
on
PJ
RMS
CJ
PN
50
-140
-135
ps
dBc/Hz
Notes 1. Measured with a 50Ω to GND termination
2: Measured at 48MHz output frequency
3. The MM8202 will support continuous VDD operation from 1.62 to 3.6V. The device can be powered up with a supply voltage at any of the 3 main supply rails of 1.8V, 2.5V or 3.3V.
4. Measured over 1000 cycles per JEDEC standard 65
5. Electrical parameters are guaranteed over the specified ambient operating temperature range, which is established when the device is mounted in a test socket with maintained
transverse airflow greater than 500lfpm. The device will meet specifications after thermal equilibrium has been reached under these conditions.
C unless otherwise noted. Typical values are measured at VDD=1.8V, T
A
=35
o
C
Parameter
ElectroStaticDischa
rge
Supply Voltage
Input LOW level
Input HIGH level
Supply Current
Quiescent Current
Output LOW level
Output HIGH level
Output Frequency
Frequency Stability
Rise Time
Fall Time
Duty Cycle
Power-up time
Period Jitter
Cycle-cycle Jitter
Phase Noise
Symbol
ESD
VDD
V
IL
V
IH
IDD
IDDQ
V
OL
V
OH
F
OUT
F
TOT
RT
FT
DC
t
on
PJ
RMS
CJ
PN
Conditions
Human Body Model, tested per JESD D22-A114
Normal Operation
3
CE pin
CE pin
Active supply current, VDD=1.8V, T=35oC, no output load
CE=LOW, output disabled
I
OL
= -1.8mA
I
OH
= 1.8mA
Factory Programmable.Contact IDT for frequencies not listed
Total Frequency Stability over temperature,supply
variation,aging (1st year at 35oC),shock&vibration. “ ” device
option, over 0-70
o
C range
20% to 80% x VDD. Output load (C
L
) =4pF, NSG-option
80% to 20% x VDD. Output load (C
L
) =4pF, NSG-option
Clock output duty cycle. Measured at VDD/2, C
L
=4pF
Output valid time after VDD meets the specified range&CE
transition
Total RMS Period Jitter (including random and
deterministic)
1,2
The absolute value of max change in the periods of any 2
adjacent cycles
1,2,4
1MHz offset from carrier
1,2
Min
4000
1.62
-0.3
VDD*0.7
Typ
Max
Units
V
1.8
2.0
0.2
VDD-0.3
6
1.98
VDD*0.3
VDD+0.3
2.5
1
0.3
133
+400
2.75
2.75
55
12,24,25,50
V
V
V
mA
µA
V
V
MHz
ppm
ns
ns
%
µs
ps
RMS
45
400
3.5
50
-140
-135
ps
dBc/Hz
Notes 1. Measured with a 50Ω to GND termination
2: Measured at 48MHz output frequency
3. The MM8202 will support continuous VDD operation from 1.62 to 3.6V. The device can be powered up with a supply voltage at any of the 3 main supply rails of 1.8V, 2.5V or 3.3V.
4. Measured over 1000 cycles per JEDEC standard 65
5. Electrical parameters are guaranteed over the specified ambient operating temperature range, which is established when the device is mounted in a test socket with maintained
transverse airflow greater than 500lfpm. The device will meet specifications after thermal equilibrium has been reached under these conditions.
Application Diagram
Below is a representative application diagram to evaluate the MM8202. For 50Ohm terminated measurements, a balun is necessary to
I want to ask if ADE7758 needs to be programmed when it is used? I see there are many function registers in it to control various functions. If it needs to be programmed, what language should be used?...
Hello everyone, we are a new startup company and we need to use Bluetooth module in our products. What we are worried about is whether it is necessary to apply for Bluetooth SIG and company identifier...
[size=4]I looked at the official code today. I modified it a little bit. You can see the retrieved HTML data through the window.[/size] [size=4] [/size] [size=4]But I found that it takes 2s-3s to wait...
Dear experts, I have found the following problem and I am puzzled. I hope you experts can answer it: 1. I directly connected ADSL modem under WinCE, and pppoe dial-up was successful, but I just couldn...
Reflow soldering is a critical process in electronics assembly production, and the cleanliness of the reflow oven has a direct impact on product quality. Dust and residue accumulation within the ov...[Details]
Core point: The automotive industry chain and the humanoid robot industry have collaborative advantages in hardware, software, and scenarios. Upstream and downstream companies in the automotive ind...[Details]
When discussing autonomous driving technology, there are often two extremes: on the one hand, there's the vision of "fully autonomous driving," while on the other, there's concern about potential s...[Details]
Pure electric vehicles, structurally speaking, have components such as a power battery. In addition to the power battery, a small battery also powers some low-voltage electrical components and even...[Details]
With the advent of the electric car era, the number of pure electric vehicles has increased significantly, but many car owners do not know how to properly maintain pure electric vehicles. In additi...[Details]
A human-machine interface (HMI) refers to the platform used by people to operate a PLC. This platform provides an interface between programs and humans, serving as a medium for information transmis...[Details]
A patent disclosed by Ford proposes replacing traditional segmented side curtain airbags with integrated full-width side curtain airbags that span the side of the vehicle and can be deployed simult...[Details]
Preface
Low-voltage motors are widely used in nonferrous metallurgical plants. Their abnormal operation not only impacts normal production but can also threaten human life. Therefore, providin...[Details]
Plug-in hybrid vehicles (PHEVs) utilize two powertrains. Their pure electric range is typically inferior to that of pure electric vehicles, often reaching less than half that. Currently, mainstream...[Details]
Civilian internal combustion engines operate in the range of approximately 1000-4000 rpm. This results in the engine's kinetic energy being ineffective at low or high rpm, making starting difficult...[Details]
0 Introduction
DVI (Digital Visual Interface) is a hot topic in current digital display research and application. Video processing technologies for DVI output not only address issues such as h...[Details]
This new standardized, pre-integrated computing platform is designed to accelerate chip development, reduce development costs, and provide scalable software to power the AI-defined car.
...[Details]
The electric motor is one of the most widely used power equipment and plays a vital role in the national economy. However, its high failure rate causes huge economic losses to industrial and agricu...[Details]
New energy electric vehicles are energy-saving, environmentally friendly, have low operating costs, and enjoy strong support from national policies. With the growth in sales of new energy electric ...[Details]
introduction
In the context of the comprehensive development of the Internet of Things (IoT) technology under the "Perceiving China" initiative, "Perceiving Mines" is a crucial component of Ch...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
