EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-7S2LA2685

Description
Transponder, 10709Mbps(Tx), 10709Mbps(Rx), LC/SPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-7S2LA2685 Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), LC/SPC Connector,

PH1-7S2LA2685 Parametric

Parameter NameAttribute value
Objectid1871047649
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Communication standardsGR-253
Connection TypeLC/SPC CONNECTOR
Data rate (receive)10709 Mbps
Data rate (send)10709 Mbps
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1530 nm
Nominal optical power output0.562 mW
minimum return loss-27 dB
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Find an ARM development board with MPEG decoding
I want to find an ARM development board with MPEG decoding. 2440 plays MPEG4, 320*240 is OK, but it is too slow if it is enlarged. Please recommend it to me if you know. I have contacted many companie...
senorspring ARM Technology
Question about stm8s iic voltage
Using stm8s103f3, mpu is powered by 3.3V, clock SD2068 is powered by 5V, can the two chips communicate directly by SCL and SDA? Please give me some advice! The iic of mpu is hardware iic, pure open dr...
honeycat205 stm32/stm8
National Semiconductor's classic book The Art of Simulation - Part 1 Topology - Op Amp
National Semiconductor's classic book The Art of Simulation - Part 1 Topology - Op Amp...
linda_xia Analog electronics
DE1-SOC development board usage learning
1. What is the Yocto build utility? What is the Linux Console with framebuffer? 2. There are several Linux distributions in the document, namely Ubuntu and LXDE versions.LXDE is a streamlined, lightwe...
Jacktang FPGA/CPLD
The use of stack in DSP
[backcolor=white][size=4][color=#000000]I am a DSP newbie. I only know that the stack is used to protect the scene when interrupting or calling a subroutine. But what is the purpose of this program se...
灞波儿奔 Microcontroller MCU
What is the special function of the import keyword under tornado?
When compiling a source file under Tornado, I found the following statement: IMPORT int Socket; IMPORT STATS_T stats; IMPORT char sysBootHost []; It can be compiled, but stats has been declared in my ...
keane Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1322  736  760  125  2893  27  15  16  3  59 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号