EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-FLHLA3085

Description
Transponder, 10660Mbps(Tx), 10660Mbps(Rx), LC/SPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-FLHLA3085 Overview

Transponder, 10660Mbps(Tx), 10660Mbps(Rx), LC/SPC Connector,

PH1-FLHLA3085 Parametric

Parameter NameAttribute value
Objectid1871051073
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Connection TypeLC/SPC CONNECTOR
Data rate (receive)10660 Mbps
Data rate (send)10660 Mbps
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1538 nm
Nominal optical power output2.511 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Design of Fire Alarm Based on Single Chip Microcomputer and GSM
I am a freshman and I am currently doing research on an innovative project on dormitory fire alarms based on single-chip microcomputers and GSM. What relevant materials are available for study?...
1400806340 Microchip MCU
TI Stellaris M3 Design Guide (Must-Read)
From TI official website, you can refer to System Design Guidelines for Stellaris Microcontrollers when designing circuits using TI M3.[[i] This post was last edited by Forever Unknown on 2011-12-30 1...
永远的不知 Microcontroller MCU
Research on the application of SVPWM generated by DSP in inverter power supply
Abstract: A method of using DSP to generate SVPWM wave to realize full digital control of inverter power supply is proposed. Based on the analysis of the characteristics of TMS320LF2407A digital signa...
zbz0529 Energy Infrastructure?
Why are the input and output levels of the MSP430F149 microcontroller TTL or COMS?
I am a newbie and just started to use MSP430 microcontrollers. I don't understand many things. Why is the input and output level of the MSP430F149 microcontroller TTL or COMS? Thank you! !...
xiamujy Microcontroller MCU
Arteli AT32WB415 peripheral use (ultrasonic module)
[i=s]This post was last edited by LYU4662 on 2022-8-8 16:46[/i]After setting up the environment last week and lighting up a lamp, I am going to learn some peripherals this time. I bought an ultrasonic...
LYU4662 RF/Wirelessly
Analysis of Microstrip Patch Antennas on Arbitrarily
Abstract—A numerical procedure for the efficient analysis ofmicrostrip antennas and feed networks embedded in multilayerstructures of arbitrary shape is presented. It is based on a specialvariant of t...
JasonYoo RF/Wirelessly

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2710  613  1261  1782  1253  55  13  26  36  46 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号