EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

100RN25P-6B2AM5-100

Description
D Type Connector, 25 Contact(s), Male, 0.05 inch Pitch, Crimp Terminal, Locking, Plug
CategoryThe connector    The connector   
File Size21MB,157 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

100RN25P-6B2AM5-100 Overview

D Type Connector, 25 Contact(s), Male, 0.05 inch Pitch, Crimp Terminal, Locking, Plug

100RN25P-6B2AM5-100 Parametric

Parameter NameAttribute value
YTEOL9
Objectid312692431
Reach Compliance Codeunknown
ECCN codeEAR99
Is SamacsysN
body width0.308 inch
subject depth0.23 inch
body length1.185 inch
Contact to complete cooperationAU ON NI
Contact point genderMALE
Contact resistance8 mΩ
Total number of contacts25
Body/casing typePLUG
Connector typeD MICROMINIATURE CONNECTOR
insulator materialPOLYPHENYLENE SULPHIDE
Installation typeCABLE
Number of rows loaded2
Rated current (signal)3 A
Shell materialALUMINUM ALLOY
Housing sizeD
contact modeSTAGGERED
Contact styleRND PIN-SKT
Installation option 1LOCKING
Contactor designPREASSEM CONN
empty shellNO
Number of connectorsONE
Contact materialCOPPER ALLOY
Plug contact pitch0.05 inch
Mixed contactsNO
Shell surfaceNICKEL
Cable typeMIL-W-16878/6
Insulator colorBLACK
Match contact row spacing0.05 inch
Installation option 2JACKSCREW
Plating thickness50u inch
Termination typeCRIMP
Dielectric withstand voltage600VAC V
Filter functionNO
Insulation resistance5000000000 Ω
Maximum wire diameter24 AWG
Minimum wire diameter24 AWG
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
LAYOUT Notes
Preparation before layout: 1 Check whether the snap point is set correctly. The snap point is 0.1 for 08 process, 0.05 for 06 process, and 0.025 for 05 process. 2 The cell name cannot start with a num...
eeleader FPGA/CPLD
【Qinheng Trial】Add SPI reference #2
1. After completing the basic framework design, gradually increase the system to increase the call of system resources, this time increase SPI. 2. SPI requires 4 pins, SPI0 is used here, which occupie...
北方 Domestic Chip Exchange
Can an expert help me write a 4-point or 1-point FFT program in Verilog?
I want to learn how to write some algorithms in Verilog, but I don't know where to start. Can an expert help me write a 4-point or 1-point FFT program in Verilog? Thanks!...
cyz1909 DSP and ARM Processors
Huaqing Yuanjian and senior experts from ARM jointly held a series of high-end technical lectures on national embedded system design based on ARM platform (Chengdu stop)
Activity introduction: As the creator of the global RISC standard, ARM's dominant position in the field of embedded processors has long been recognized by everyone. Currently, more than 90% of embedde...
xwell ARM Technology
Detection of mV AM Signals at Input to Op Amp
:Cry: Can anyone provide a circuit for receiving weak AM signals? Not the kind of AM radio with an antenna....
zhaoyanfeng520 TI Technology Forum
Share a circuit board design software that is better than Protel plus video tutorials
PADS schematic and circuit board design full process video (8 hours)-06 PADS is the most commonly used circuit board design software in China, and is favored by the majority of electronic hardware des...
眼大5子 PCB Design

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2317  1177  1641  948  1155  47  24  34  20  13 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号