Active low indicates incoming ring signal. This is pulsed low by
the AC ring signal, and is not a steady-state low during ringing.
Return Path for V
CC
Driving this pin low asserts the off-hook condition. The hook
switch LED is current limited by an internal 470 resistor.
Not Used
Provides power to the hook switch LED. Voltage is usually +5V
(for 8mA LED current), but can be higher if an external resistor
is placed in series with the internal 470 resistor.
Connection to telephone line Ring conductor.
Connection to telephone line Tip conductor.
4
5
6
7
10
11
Top
View
3
www.ixysic.com
R02
I
NTEGRATED
C
IRCUITS
D
IVISION
2 Manufacturing Information
2.1 Handling and Assembly Recommendations
CYG2110
The CYG2110 is not hermetically sealed, and should not be exposed to any liquid-based rinsing processes. IXYS
Integrated Circuits Division recommends two (2) approaches: (1) the modem should be installed in a wave-soldering
process that uses a no-clean soldering flux that will mostly evaporate during the normal wave-soldering processes,
(2) the modem should be soldered in by hand after the rest of the card is wave-soldered.
2.2 Reflow Profile
This product has a maximum solder temperature as shown below.
Device
CYG2110
Maximum Temperature
260°C
2.3 Mechanical Dimensions
2.3.1 CYG2110
1.91
(0.075)
27.18
(1.070)
10.16
(0.400)
21.59
(0.850)
LINE 1 (PIN 1)
LINE 2
RING
27.18
(1.070)
GND
OH
MUTE
V
CC
TIP
RING
0.634 SQ.
(0.025)
TYP.
1.09 DIA.
(0.043)
TYP.
PCB Pattern
(Top View)
Dimensions
mm
(inches)
2.54
(0.100)
typ.
3.43
(0.135)
3.18
(0.125)
TOP VIEW
SIDE VIEW
For additional information please visit our website at: www.ixysic.com
IXYS Integrated Circuits Division makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make
changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in IXYS Integrated
Circuits Division’s Standard Terms and Conditions of Sale, IXYS Integrated Circuits Division assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its
products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.
The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other
applications intended to support or sustain life, or where malfunction of IXYS Integrated Circuits Division’s product may result in direct physical harm, injury, or death to a person or severe
property or environmental damage. IXYS Integrated Circuits Division reserves the right to discontinue or make changes to its products at any time without notice.
I wrote a simple script as the title, and saved it as main.py import time from machine import Pin led=Pin(2,Pin.OUT) #create LED object from pin2,Set Pin2 to output while True: led.value(1) #Set led t...
For the push-pull topology in the figure below, the battery voltage input is about 40 volts. For example, when the lower tube is turned on and the upper tube is turned off, it works normally. But when...
The written program is downloaded to SDRAM or Nand flash through U-BOOT. The timing of the running lights is different. What's going on? It is much faster when in SDRAM, and much slower when booting f...
MicroPython Open Source section
京公网安备 11010802033920号
EEWORLD
