Application Note AN110A
SPST (Form A)
Reed Switch Selector Guide
SPDT (Form C)
Switching Standard
"B"
"C"
Switching Current Sensitivity
"A"
Overall
Glass Body
Max
(Pull-In)
Length
Diameter
Switching Voltage
Glass Body
Switch
Contact
Range
Length Max
(Wires)
Max
Power Max [Volt] [Ampere]
Name
Key Features
Form
Max [W] (Note 1)
(Note 2)
[AT]
[mm[inch]]
[mm[inch]]
[mm[inch]]
MITI-3V1 Ultra Small (7mm glass body)
A (SPST)
10 W
170 Vdc
0.5 Adc
6-15
7.00 [.276] 46.00 [1.810] 1.80 [.071]
MDSR-10 Very Small (10mm glass body)
A (SPST)
10 W
200 Vdc
0.5 Adc
10-25
10.16 [.400] 40.38 [1.590] 1.80 [.071]
MDSR-7 Small (12.7mm glass body)
A (SPST)
10 W
200 Vdc
0.5 Adc
10-25
12.70 [.500] 40.38 [1.590] 1.80 [.071]
FLEX-14 Flexible Leads (14mm glass body) A (SPST)
10 W
200 Vdc
0.5 Adc
10-30
14.00 [.551] 44.30 [1.744] 2.28 [.090]
MDCG-4 General Purpose Switch
A (SPST)
10 W
200 Vdc
0.5 Adc
12-38
15.24 [.600] 40.38 [1.590] 2.28 [.090]
MDRR-6 240 VAC switching
A (SPST)
10 W
265 Vac 0.35 Aac
17-38
15.24 [.600] 40.38 [1.590] 2.28 [.090]
MLRR-4
Small Hysteresis (Differential)
A (SPST)
20 W
200 Vdc
1.0 Adc
17-38
15.24 [.600] 40.38 [1.590] 2.54 [.100]
MLRR-3
Long Leads, Switching Load/Life A (SPST)
20 W
200 Vdc
1.0 Adc
17-38
15.24 [.600] 56.64 [2.230] 2.54 [.100]
MARR-5 Very High Voltage
A (SPST)
10 W
1000 Vdc 0.5 Adc
17-38
19.69 [.775] 56.77 [2.235] 2.66 [.105]
MRPR-1 Wide Hysteresis (Differential)
A (SPST)
50 W
200 Vdc
1.0 Adc
22-43
19.69 [.775] 56.64 [2.230] 2.84 [.112]
MRPR-3 High Power
A (SPST)
50 W
200 Vdc
1.5 Adc
22-43
19.69 [.775] 56.64 [2.230] 2.84 [.112]
MRPR-8 240 VAC switching, High Power
A (SPST)
50 W
265 Vac
0.7 Aac
22-43
20.32 [.800] 56.64 [2.230] 2.84 [.112]
DRR-129
Big, High Power
A (SPST)
C (SPDT)
C (SPDT)
C (SPDT)
100 W
5W
30 W
50 W
400 Vdc
175 Vdc
500 Vdc
500 Vdc
3.0 Adc
0.25 Adc
0.5 Adc
1.5 Adc
42-83
15-30
50-80
50-80
50.80 [2.000] 82.55 [3.250] 5.25 [.207]
14.73 [.580] 51.66 [2.034] 2.54 [.100]
39.67 [1.562] 85.73 [3.375] 5.33 [.210]
39.67 [1.562] 85.73 [3.375] 5.33 [.210]
"D"
Wire
Diameter
Nominal
[mm[inch]]
0.38 [.015]
0.43 [.017]
0.47 [.019]
0.47 [.019]
0.50 [.020]
0.50 [.020]
0.61 [.024]
0.61 [.024]
0.55 [.022]
0.63 [.025]
0.63 [.025]
0.63 [.025]
Flattened
0.51&0.56
[.020&.022]
1.02&1.27
[.040&.050]
1.02&1.27
[.040&.050]
MDRR-DT Small Form C (SPDT)
DRR-DTH Big Power Form C (SPDT)
DRT-DTH Big High Power Form C (SPDT)
NOTES:
1. AC voltage rating is .707 times DC rating except MDRR-6 is 200 Vdc and MRPR-8 is 250 Vdc
2. AC current rating is .707 times DC rating (For MDRR-6 & MRPR-8, DC current rating is 1.414 times AC current rating)
www.hamlin.com
© 2007 Hamlin Electronics L. P.
p 1/3
Application Note AN110A
MITI-3V1
Because of the higher cost, this reed switch is used only when size is an important factor. This switch is also available in surface-mount as the
MISM-3V1R (Tape & Reel) and MISM-3V1B (Bulk Pack).
MDSR-10
This is a cost-effective small reed switch. This switch is also available in surface-mount as the MDSM-10R (Tape & Reel), MDSM-10B (Bulk
Pack), and the 59170 (overmolded).
MDSR-7
This is a small reed switch, but not as small as the switches above. The glass diameter is the same small size as the switches above. This switch
is also available in an overmolded PCB-mount package, including surface-mount, as the 59165 and 59045.
FLEX-14
The leads on the FLEX-14 are easily formed or bent to meet an application’s requirements. In addition, the slightly shorter glass length and
slightly longer lead length provide greater flexibility in designing into products.
MDCG-4
The MDCG-4 is one of Hamlin’s most popular reed switches. It is available in a wide range of sensitivities. It is also available in an overmolded
PCB-mount package as the 59050, and surface-mount as the MDSM-4R (Tape & Reel) and MDSM-4B (Bulk Pack).
MDRR-6
The MDRR-6 is physically very similar to the MDCG-4, but it utilizes a pressurized nitrogen atmosphere that allows switching 240 Vac power line
mains voltages. The MDRR-6 also has good life on non-suppressed inductive loads as well as less demanding ones. It is available in a wide
variety of Hamlin sensor packages including the PCB-Mount 59050.
MLRR-4
The MLRR-4 has the smallest hysteresis between activate and deactivate (close differential). This can be an advantage in some sensing
applications, but it can also be a disadvantage in sensing applications where the magnet is moving slowly. The MLRR-4 also performs well
switching small incandescent lamps (< 28 V, < 0.2 A). This switch is also available in surface-mount as the MLSM-4R (Tape & Reel) and MLSM-
4B (Bulk Pack).
MLRR-3
This reed switch has the longest wire leads of any of the 15.24 mm / 0.600 inch glass length switches. The MLRR-3 is a cost-effective small 20
Watt switch. It has good life on a wide range of loads. It is also available in surface-mount as the MLSM-3R (Tape & Reel) and MLSM-3B (Bulk
Pack).
www.hamlin.com
© 2007 Hamlin Electronics L. P.
p 2/3
Application Note AN110A
MARR-5
The MARR-5 has advantages in high voltage and low temperature applications because the electrical contacts are in a vacuum instead of a
nitrogen atmosphere. The voltage ratings are 1000 Vdc switching and 2000 Vdc breakdown (see data sheet for additional information). The
switch is rated at a rather high 35 AT (Ampere-turn) in order to meet the 1000 Vdc switching voltage at low currents (< 10 mA). If a higher
switching current or RC arc suppression is used, a higher switching voltage or lower switch AT value can be realized. Contact Hamlin for
recommendations. As the switch AT increases (sensitivity decreases), the contact gap increases, resulting in increased voltage capability.
Typical breakdown voltage is 100 times the AT value. In addition, the MARR-5 can be used at temperatures near absolute zero if carefully
packaged. For additional information, see Hamlin Application Note AN105 – Extreme Temperature Reed Switch Operation
MRPR-1
Because of its flexible reed and thin contact coating, the MRPR-1 has the largest hysteresis between activate and deactivate (wide differential).
The carry current of 3.0 Adc is also quite high.
MRPR-3
The MRPR-3 is very good at switching relatively high power loads up to 50 W, 200 Vdc 140 Vac, 1.5 Adc 1.1 Aac, including inductive loads with or
without an inrush current.
MRPR-8
The MRPR-8 utilizes a pressurized nitrogen atmosphere that allows switching 240 Vac power line mains voltages and higher power levels
compared to the MDRR-6
MDRR-DT
This is a single-pole double-throw (SPDT) reed switch, also known as a Form C reed switch. The addition of a normally-closed contact to the
standard normally-open contact meets the needs of a wide variety of applications. It is not unusual for the normally-closed contact to be the only
contact used in an application. However, this capability results in comprises that affect the switching voltage & current, as well as cost.
DRR-129
The DRR-129 has the highest electrical contact ratings of all Hamlin’s reed switches. This is because of the large wire diameter and large contact
gap. These characteristics also create disadvantages in size, cost, and low magnetic sensitivity. Still, the 100 W, 400 V 3 A switching capability is
sometimes needed in applications.
DRR-DTH & DRT-DTH
Like the MDRR-DT, these are single-pole double-throw (SPDT) reed switches. Their large size increases electrical performance but also
increases cost. The DRR-DTH uses a contact coating similar to many of Hamlin’s reed switches. The DRT-DTH uses a tungsten contact coating
that is very good on heavy loads but tends to increase contact resistance when switching light loads such as < 0.25 A, < 6 V.
www.hamlin.com
© 2007 Hamlin Electronics L. P.
p 3/3
Embedded System
京公网安备 11010802033920号
EEWORLD
