EEWORLDEEWORLDEEWORLD

Part Number

Search

3GW8E-80N-800.00

Description
LVCMOS Output Clock Oscillator, 800MHz Nom, ROHS AND REACH COMPLIANT, DIP-8/4
CategoryPassive components    oscillator   
File Size126KB,1 Pages
ManufacturerEuroquartz
Websitehttp://www.euroquartz.co.uk/
Environmental Compliance  
Download Datasheet Parametric View All

3GW8E-80N-800.00 Overview

LVCMOS Output Clock Oscillator, 800MHz Nom, ROHS AND REACH COMPLIANT, DIP-8/4

3GW8E-80N-800.00 Parametric

Parameter NameAttribute value
physical size12.8mm x 12.8mm x 5.08mm
Is it lead-free?Yes
Is it Rohs certified?Yes
YTEOL2
Objectid1063499857
package instructionROHS AND REACH COMPLIANT, DIP-8/4
Reach Compliance Codecompliant
Is SamacsysN
Frequency Adjustment - MechanicalNO
Frequency offset/pull rate80 ppm
linearity10%
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
maximum symmetry55/45 %
Maximum control voltage1.85 V
Minimum control voltage1.45 V
Oscillator typeLVCMOS
Output load15 pF
Nominal supply voltage3.3 V
frequency stability50%
Nominal operating frequency800 MHz
Number of terminals8
surface mountNO
Installation featuresTHROUGH HOLE MOUNT
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
EURO
QUARTZ
8 pin Dual-in-Line
Frequency range 200.1MHz to 800MHz
LVCMOS Output
Supply Voltage 3.3 VDC
High Q fundamental mode crystal
Low jitter multiplier circuit
DESCRIPTION
OUTLINE & DIMENSIONS
GW42 VCXOs, are packaged in an industry-standard, 4 pad, 11.4mm
x 9.6mm x 2.5mm SMD package. GW42 VCXOs incorporate a high Q
fundamental crystal and a low jitter multiplier circuit.
SPECIFICATION
Frequency Range:
Supply Voltage:
Output Logic:
Integrated Phase Jitter:
Period Jitter RMS:
Period Jitter Peak to peak:
Phase Noise:
Initial Frequency Accuracy:
Output Voltage HIGH (1):
Output Voltage LOW (0):
Pulling Range:
Temperature Stability:
Output Load:
Start-up Time:
Duty Cycle:
Rise/Fall Times:
Current Consumption
<96MHz:
>96MHz:
Linearity:
Modulation Bandwidth:
Input Impedance:
Slope Polarity:
(Transfer function)
GW8 VCXO
200.1MHz ~ 800.0MHz
200.1MHz to 800.0MHz
3.3 VDC ±5%
LVCMOS
2.6ps typical, 4.0ps maximum
(for 155.250MHz)
4.3ps typical (for 155.250MHz)
27.0ps typical (for 155.250MHz)
Tune to the nominal frequency
with Vc= 1.65 ±0.2VDC
90% Vdd minimum
10% Vdd maximum
From ±30ppm to ±150ppm
15pF
10ms maximum, 5ms typical
50% ±5% measured at 50% Vdd
1.2ns typical (15pF load)
30mA maximum (15pF load)
40mA maximum (15pF load)
10% maximum, 6% typical
25kHz minimum
2 MW minimum
Monotonic and Positive. (
PHASE NOISE
10Hz
100Hz
1kHz
10kHz
100kHz
1MHz
10MHz
-65dBc/Hz
-95dBc/Hz
-120dBc/Hz
-125dBc/Hz
-121dBc/Hz
-120dBc/Hz
-140dBc/Hz
Storage Temperature:
Ageing:
Enable/Disable (Tristate):
RoHS Status:
-50° to +100°C
±5ppm per year maximum
Not available (
Fully compliant
)
PART NUMBER SCHEDULE
Example:
FREQUENCY STABILITY
Stability Code Stability ±ppm Temp. Range
A
25
0°~+70°C
B
50
0°~+70°C
C
100
0°~+70°C
D
25
-40°~+85°C
E
50
-40°~+85°C
F
100
-40°~+85°C
If non-standard frequency stability is required
Use ‘I’ followed by stability, i.e. I20 for ±20ppm
3GW8B-80N-250.00
Supply Voltage
3 = +3.3V
Series Designator
GW8
Stability over temperature range
(
)
Pullability in ±ppm
Pullability determinator
N = minimum
M = maximum
T = Typical
Frequency in MHz
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 info@euroquartz.co.uk www.euroquartz.co.uk
Analysis of LED drive solutions
...
czf0408 Power technology
Have a question?
When using a chip, is it enough to just be familiar with its application circuit, or is it better to be familiar with its principle (application circuit or chip), such as an op amp circuit?...
kailern Embedded System
What should I do if the previous interrupt program is not completed and is requested again next time?
When M128 interrupt occurs, the previous interrupt has not been completed, and the next interrupt request comes. At this time, does the processor abandon the next interrupt request and execute the unf...
单片机终结者 Microchip MCU
Arm downloads to flash pictures with garbled characters
Operation 2440, extract a picture in C array format and put it into the program. The program can run in RAM, but when the program is downloaded to NAND FLASH, the LCD displays the picture in a mess, a...
lsbhjl ARM Technology
MB90092 secondary screen display problem
Hello everyone, I am working on mb90092 character overlay recently, using the secondary screen display, but no matter how I set it, it is garbled. Can anyone who has used it give me some advice? QQ: 1...
ddfha1 51mcu
LabVIEW calls the system execution node SYTEM EXEC
I have collected a list of DOS commands in the quick reference table. For people in the 386 era, most people had no access to computers. DOS commands were the only system tools for communicating with ...
chaoren Test/Measurement

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1133  2824  423  785  155  23  57  9  16  4 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号