EEWORLDEEWORLDEEWORLD

Part Number

Search

B0202GA-03-2673-D

Description
Fixed Resistor, Thin Film, 0.25W, 267000ohm, 100V, 0.5% +/-Tol, 25ppm/Cel, Surface Mount, 0202, CHIP
CategoryPassive components    The resistor   
File Size381KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

B0202GA-03-2673-D Overview

Fixed Resistor, Thin Film, 0.25W, 267000ohm, 100V, 0.5% +/-Tol, 25ppm/Cel, Surface Mount, 0202, CHIP

B0202GA-03-2673-D Parametric

Parameter NameAttribute value
Rated temperature70 °C
surface mountYES
Operating Voltage100 V
Reach Compliance Codecompliant
ECCN codeEAR99
Is SamacsysN
YTEOL0
Objectid1579389960
package instruction, 0202
Tolerance0.5%
Installation featuresSURFACE MOUNT
Rated power dissipation(P)0.25 W
resistance267000 Ω
Resistor typeFIXED RESISTOR
size code0202
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Number of terminals2
Package shapeRECTANGULAR PACKAGE
method of packingTRAY
Terminal shapeONE SURFACE
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed P x R )
Operating Temperature
Back contact
Noise
R
Top contact
pad chamfered
0.004˝ min bond pad size
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Al / Au optional)
3KÅ Au minimum
10KÅ Al minimum
Silicon Dioxide or
Silicon Nitride
R
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
½R
½R
Backside
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
Passivation
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue January 2009 Sheet 1 of 3
The CCA pin of CC2420 is always low.
Could any of you help me out? Why is the CCA channel evaluation pin of my CC2420 module always at low level before or after configuration? Even when other pins are left floating, CCA is still at low l...
神话 RF/Wirelessly
Help ADS1232
Has anyone used ads1232? I am a rookie who just came to the company for internship. The company gave me an ads1232 board and asked me to make a driver. Is there anyone willing to help?...
hustxsh Embedded System
【GD32450I-EVAL】Transplant touch to LittleVGL
The previous post tested the touch driver: SPI transceiver and touch chip XPT2046 driver and pen interrupt The next step is to port to LittleVGL. Last time when I ported LittleVGL's display, I left be...
tinnu GD32 MCU
Share the process of WEBENCH design + design power supply circuit for TI's AM1705BPTP3
Requirement: The power supply requirements for TI's AM1705BPTP3 are as follows: # Name VLoad ILoad Description 1. CVDD 1.2 V 3.75 A VoutRipple=18%, Up Sequence Order=1 delay=2.0 kSec 2. DVDD 3.3 V 1.1...
youzizhile Analogue and Mixed Signal
pickit3 is an independent burning software and cannot import hex.
Requirements. Now we need to batch burn pic microcontrollers in the factory (far away from the company). On a computer, install mplab ide, open the software, and it prompts that it cannot find Java 1....
ienglgge Microchip MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2124  923  541  614  1747  43  19  11  13  36 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号