V+ and V- can have maximum magnitudes of 7V, but their absolute difference cannot exceed 13V.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
CC
= +3V to +5.5V, C1–C4 = 0.1µF, tested at 3.3V ±10%; C
1
= 0.047µF, C2–C4 = 0.33µF, tested at 5.0V ±10%; T
A
= T
MIN
to T
MAX
,
unless otherwise noted. Typical values are at T
A
= +25°C.)
PARAMETER
Supply Current,
AutoShutdown Plus
Supply Current, Shutdown
Supply Current,
AutoShutdown Plus Disabled
LOGIC INPUTS AND RECEIVER OUTPUTS
Input Logic Threshold Low
Input Logic Threshold High
Transmitter Input Hysteresis
Input Leakage Current
Output Leakage Current
Output Voltage Low
Output Voltage High
RECEIVER INPUTS
Input Voltage Range
Input Threshold Low
Input Threshold High
Input Hysteresis
Input Resistance
2
SYMBOL
CONDITIONS
FORCEON = GND,
FORCEOFF
= V
CC
,
all R_IN idle, all T_IN idle
FORCEOFF
= GND
FORCEON =
FORCEOFF
= V
CC
, no load
MIN
TYP
MAX
UNITS
DC CHARACTERISTICS
(V
CC
= 3.3V or 5.0V, T
A
= +25°C)
1
1
0.3
10
10
1
µA
µA
mA
T_IN, FORCEON,
FORCEOFF
T_IN, FORCEON,
FORCEOFF
V
CC
= 3.3V
V
CC
= 5.0V
2
2.4
0.5
T_IN, FORCEON,
FORCEOFF
R_OUT (MAX3244E/MAX3245E), receivers
disabled
I
OUT
= 1.6mA
I
OUT
= -1.0mA
V
CC
- 0.6 V
CC
- 0.1
-25
T
A
= +25°C
T
A
= +25°C
V
CC
= 3.3V
V
CC
= 5.0V
V
CC
= 3.3V
V
CC
= 5.0V
3
0.6
0.8
1.2
1.5
1.5
1.8
0.5
T
A
= +25°C
5
±0.01
±0.05
0.8
V
V
V
±1
±10
0.4
µA
µA
V
V
+25
V
V
2.4
2.4
7
V
V
kΩ
Maxim Integrated
MAX3224E/MAX3225E/
MAX3226E/MAX3227E/MAX3244E/MAX3245E
±15kV ESD-Protected, 1µA, 1Mbps, 3.0V to 5.5V,
RS-232 Transceivers with AutoShutdown Plus
ELECTRICAL CHARACTERISTICS (continued)
(V
CC
= +3V to +5.5V, C1–C4 = 0.1µF, tested at 3.3V ±10%; C
1
= 0.047µF, C2–C4 = 0.33µF, tested at 5.0V ±10%; T
A
= T
MIN
to T
MAX
,
unless otherwise noted. Typical values are at T
A
= +25°C.)
PARAMETER
TRANSMITTER OUTPUTS
Output Voltage Swing
Output Resistance
Output Short-Circuit Current
Output Leakage Current
V
CC
= 0V or 3V to 5.5V, V
OUT
= ±12V,
Transmitters disabled
All transmitter outputs loaded with 3kΩ to
ground
V
CC
= V+ = V- = 0V, transmitter outputs = ±2V
±5
300
±5.4
10M
±60
±25
V
Ω
mA
µA
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
MOUSE DRIVEABILITY
(MAX3244E/MAX3245E)
T1IN = T2IN = GND, T3IN = V
CC
,
T3OUT loaded with 3kΩ to GND,
T1OUT and T2OUT loaded with
2.5mA each
IEC 1000-4-2 Air Discharge
R_IN, T_OUT
IEC 1000-4-2 Contact Discharge
Human Body Model
AutoShutdown Plus
(FORCEON = GND,
FORCEOFF
= V
CC
)
Receiver Input Threshold to
INVALID
Output High
Receiver Input Threshold to
INVALID
Output Low
INVALID,
READY
Output Voltage Low
(MAX3224E–MAX3227E)
INVALID,
READY
Output Voltage High
(MAX3224E–MAX3227E)
Receiver Positive or Negative
Threshold to
INVALID
High
Receiver Positive or Negative
Threshold to
INVALID
Low
Receiver or Transmitter Edge to
Transmitters Enabled
t
INVH
t
INVL
t
WU
Figure 4a
Figure 4a
Positive threshold
Negative threshold
-2.7
-0.3
+0.3
2.7
V
V
Transmitter Output Voltage
ESD PROTECTION
±5
V
±15
±8
±15
kV
I
OUT
= -1.6mA
0.4
V
I
OUT
= -1.0mA
V
CC
- 0.6
V
V
CC
= 5V, Figure 4b
V
CC
= 5V, Figure 4b
V
CC
= 5V, Figure 5b (Note 2)
15
1
30
100
30
60
µs
µs
µs
s
Receiver or Transmitter Edge to
t
AUTOSHDN
V
CC
= 5V, Figure 5b (Note 2)
Transmitters Shutdown
Maxim Integrated
3
MAX3224E/MAX3225E/
MAX3226E/MAX3227E/MAX3244E/MAX3245E
±15kV ESD-Protected, 1µA, 1Mbps, 3.0V to 5.5V,
RS-232 Transceivers with AutoShutdown Plus
TIMING CHARACTERISTICS—MAX3224E/MAX3226E/MAX3244E
(V
CC
= +3V to +5.5V, C1–C4 = 0.1µF, tested at 3.3V ±10%; C
1
= 0.047µF, C2–C4 = 0.33µF, tested at 5.0V ±10%; T
A
= T
MIN
to T
MAX
,
unless otherwise noted. Typical values are at T
A
= +25°C.)
PARAMETER
Maximum Data Rate
Receiver Propagation Delay
Receiver Output Enable Time
Receiver Output Disable Time
Transmitter Skew
Receiver Skew
⏐
t
PHL
- t
PLH
⏐
⏐
t
PHL
- t
PLH
⏐
t
PHL
t
PLH
SYMBOL
CONDITIONS
R
L
= 3kΩ, C
L
= 1000pF,
one transmitter switching
R_IN to R_OUT, C
L
= 150pF
Normal operation (MAX3244E only)
Normal operation (MAX3244E only)
(Note 3)
V
CC
= 3.3V, T
A
= +25°C,
R
L
= 3kΩ to 7kΩ,
measured from +3V to -3V
or -3V to +3V, one trans-
mitter switching
MIN
250
0.15
0.15
200
200
100
50
C
L
= 150pF
to 1000pF
TYP
MAX
UNITS
kbps
µs
ns
ns
ns
ns
Transition-Region Slew Rate
6
30
V/µs
TIMING CHARACTERISTICS—MAX3225E/MAX3227E/MAX3245E
(V
CC
= +3V to +5.5V, C1–C4 = 0.1µF, tested at 3.3V ±10%; C
1
= 0.047µF, C2–C4 = 0.33µF, tested at 5.0V ±10%; T
A
= T
MIN
to T
MAX
,
unless otherwise noted. Typical values are at T
A
= +25°C.)
PARAMETER
SYMBOL
CONDITIONS
R
L
= 3kΩ, C
L
= 1000pF,
one transmitter switching
Maximum Data Rate
V
CC
= 3.0V to 4.5V, R
L
= 3kΩ,
C
L
= 250pF, one transmitter switching
V
CC
= 4.5V to 5.5V, R
L
= 3kΩ,
C
L
= 1000pF, one transmitter switching
Receiver Propagation Delay
Receiver Output Enable Time
Receiver Output Disable Time
Transmitter Skew
Receiver Skew
⏐
t
PHL
- t
PLH
⏐
⏐
t
PHL
- t
PLH
⏐
t
PHL
t
PLH
R_IN to R_OUT, C
L
= 150pF
Normal operation (MAX3245E only)
Normal operation (MAX3245E only)
(Note 3)
MIN
250
1000
1000
0.15
0.15
200
200
25
50
µs
ns
ns
ns
ns
V/µs
kbps
TYP
MAX
UNITS
V
CC
= 3.3V, T
A
= +25°C,
R
L
= 3kΩ to 7kΩ, C
L
= 150pF to 1000pF,
Transition-Region Slew Rate
24
150
measured from +3V to -3V or -3V to +3V,
one transmitter switching
Note 2:
A transmitter/receiver edge is defined as a transition through the transmitter/receiver input logic thresholds.
Note 3:
Transmitter skew is measured at the transmitter zero cross points.
[i=s]This post was last edited by qwqwqw2088 on 2015-10-30 20:40[/i] [color=#a0522d][font=Verdana]Wireless power systems continue to gain acceptance in mobile phones and other small portable applicati...
I use VB.net2005 to develop a WinCE program. I want to call the print dialog box of the WinCE system. How should I write it to call the print dialog box?...
I have a project, the manufacturer requires to display the instantaneous flow rate as the flow rate per hour. I plan to collect the corresponding pressure, temperature, differential pressure, and freq...
I wrote a small software to send data on my PC. The purpose is to send a string of characters through the USB port. The function is writeport(). It is transmitted to the DE2-70 experimental board thro...
[i=s] This post was last edited by qwqwqw2088 on 2014-8-14 23:07 [/i] 1. Design topic: 2.8V-4.2V step-down output 2.5V0.8A circuit 2. Design process Enter the design page and enter the circuit paramet...
introduction
my country has a vast territory and a large population. The scale of housing construction is huge, and the amount of residential construction is large and wide. It is still on t...[Details]
Google's driverless technology is not only an eye-catching technology, but also a subversion of the car usage model.
Those who have watched anti-terrorism films and TV dramas must have been im...[Details]
Due to the significant increase in electronic devices in automotive and industrial applications, the automotive and industrial markets continue to play an important role in China's electronics in...[Details]
introduction
For the voltage regulator modules (VRMs) that power the latest computer central processing units (CPUs), power supply designers have historically used multiphase interleaved b...[Details]
This paper establishes a fuel cell engine test platform based on the NI integrated hardware and software environment. This platform can realize the test and control of fuel cell engines and their a...[Details]
Overview
As a remote network communication control method with advanced technology, high reliability, complete functions and reasonable cost, CAN-bus has been widely used in various automa...[Details]
Analysis of the three core aspects of digital TV transmission standards
According to the differences in regionality, transmission method and modulation method, the transmission method needs to...[Details]
Distributed Wireless Communication System (DWCS) uses distributed antennas, distributed processing control, joint signal processing and other technologies to improve the system's spectrum efficie...[Details]
For battery-powered portable devices, in addition to breaking through the limitations of processing power, the performance of portable system power supplies also needs to be continuously improved. ...[Details]
The power supply is the core component of a computer. Although it is not of high value, all computer components rely on the switching power adapter to provide energy, so the stability of a power su...[Details]
introduction
Temperature and humidity are the main environmental parameters of industrial and agricultural production. It is of great significance to measure them accurately and timely. Using a s...[Details]
1. Introduction
Modern modular machine tools are equipped with a large number of electronic devices to meet the requirements of processing accuracy, processing speed, etc. If the conventional ...[Details]
In the 1980s, breakthroughs were made in the design and production of small, low-power quartz metal halide lamps with precise dimensions. At the same time, with the acceleration of people's lives a...[Details]
1. Overview
With the development of science and technology, PLC is increasingly used in industrial control. The reliability of PLC control systems directly affects the safe production and economic o...[Details]
When designing a PLC system, the control scheme should be determined first, and the next step is to select the PLC engineering design. The characteristics of the process and the application require...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
