EEWORLDEEWORLDEEWORLD

Part Number

Search

DRF-B25S-OT-113

Description
D Type Connector, 25 Contact(s), Female, 0.109 inch Pitch, Solder Terminal, Hole .125-.137, Plug
CategoryThe connector    The connector   
File Size309KB,5 Pages
ManufacturerSingatron Enterprises Co
Download Datasheet Parametric View All

DRF-B25S-OT-113 Overview

D Type Connector, 25 Contact(s), Female, 0.109 inch Pitch, Solder Terminal, Hole .125-.137, Plug

DRF-B25S-OT-113 Parametric

Parameter NameAttribute value
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
GuidelineUL
Is SamacsysN
Objectid1157585803
Reach Compliance CodeCompliant
ECCN codeEAR99
Number of rows loaded2
Body/casing typePLUG
insulator materialGLASS FILLED POLYBUTYLENE TEREPHTHALATE
Installation typeBOARD
Contact to complete cooperationAU ON NI
Rated current (signal)5 A
PCB row number2
Terminal pitch2.7686 mm
Other featuresFERRITE FILTER, 0.318 FTPRINT
Contact point genderFEMALE
Contact resistance8 mΩ
Connector typeD SUBMINIATURE CONNECTOR
Installation methodRIGHT ANGLE
Total number of contacts25
body width0.494 inch
body length2.088 inch
Terminal length0.125 inch
Plug contact pitch0.109 inch
Termination typeSOLDER
Match contact row spacing0.112 inch
OptionsGENERAL PURPOSE
PCB contact patternSTAGGERED
Plating thicknessFLASH inch
Installation option 1HOLE .125-.137
PCB contact row spacing2.8448 mm
Contact completed and terminatedGOLD
Contact materialPHOSPHOR BRONZE
contact modeSTAGGERED
Contact styleRND PIN-SKT
Insulator colorWHITE
Installation option 2NON-THREADED
Dielectric withstand voltage1000VAC V
Filter functionYES
maximum insertion force2.502 N
Insulation resistance5000000000 Ω
Evacuation force-minimum value1.112 N
Read the good book "Operational Amplifier Parameter Analysis and LTspice Application Simulation" 05 Offset Voltage Case Analysis
I don't know when it started, but I've become so impressed by the typical values of op amp parameters that I've paid less attention to the maximum and minimum values. The gold medalists are always the...
1nnocent Analog electronics
Question + How to create a 3D scene
I'm doing some experiments on gesture recognition recently, and I don't know how to build a 3D scene like the one below. I checked the information, and it's basically OpenGL, but it's a bit difficult....
lonerzf Integrated technical exchanges
Why can't Keil compile?
I recently wrote a program for infrared temperature measurement on SMbus, but I don't know why it can't be compiled. I would like some advice from the experts. The specific code is as follows #include...
sillman 51mcu
Digital tube glyph code automatic generator
This is a very small and practical software, which can quickly calculate the 8-segment digital tube glyph code of any connection method. It is a very good thing, share it with others...
1985rose Analog electronics
ADS1258 analog-to-digital converter data reading rate problem
I am using the ADS1258 chip recently. The chip is configured with a data rate of 23.7KSPS/channel and 16 single-ended input channels, of which /DRDY is connected to the interrupt input IO of the MCU. ...
Aaron Analogue and Mixed Signal
PCB Type
How to use ProtelDXP to design the PCB board into a large semicircle (i.e. a small part of the circle is cut off), which is the appearance of the board. I know that it is possible to place a circular ...
eplj_163 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 346  2215  1017  2808  1708  7  45  21  57  35 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号