EEWORLDEEWORLDEEWORLD

Part Number

Search

8N4S273KC-0090CDI8

Description
LVDS Output Clock Oscillator
CategoryPassive components    oscillator   
File Size613KB,18 Pages
ManufacturerIDT (Integrated Device Technology)
Download Datasheet Parametric View All

8N4S273KC-0090CDI8 Overview

LVDS Output Clock Oscillator

8N4S273KC-0090CDI8 Parametric

Parameter NameAttribute value
Number of terminals6
Package body materialCERAMIC
Encapsulate equivalent codeDILCC6,.2
surface mountYES
Installation featuresSURFACE MOUNT
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
physical size7.0mm x 5.0mm x 1.55mm
Is SamacsysN
YTEOL0
Objectid1315782661
Reach Compliance CodeUnknown
longest rise time0.45 ns
Maximum slew rate160 mA
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
maximum symmetry53/47 %
Other featuresENABLE/DISABLE FUNCTION; DIFFERENTIAL OUTPUT
maximum descent time0.45 ns
Frequency Adjustment - MechanicalNO
frequency stability20%
Maximum operating frequency1300 MHz
Minimum operating frequency975 MHz
Oscillator typeLVDS
Output load50 OHM
Nominal supply voltage3.3 V
LVDS Frequency-Programmable
Crystal Oscillator
IDT8N4S273
DATA SHEET
General Description
The IDT8N4S273 is a Factory Frequency-Programmable Crystal
Oscillator with very flexible frequency programming capabilities. The
device uses IDT’s fourth generation FemtoClock
®
NG technology for
an optimum of high clock frequency and low phase noise
performance. The device accepts 2.5V or 3.3V supply and is
packaged in a small, lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm
x 1.55mm package.
The device can be factory programmed to any in the range from
15.476MHz to 866.67MHz and from 975MHz to 1,300MHz and
supports a very high degree of frequency precision of 218Hz or
better. The extended temperature range supports wireless
infrastructure, telecommunication and networking end equipment
requirements.
Features
Fourth generation FemtoClock
®
NG technology
Factory-programmable clock output frequency from 15.476MHz
to 866.67MHz and from 975MHz to 1,300MHz
Frequency programming resolution is 218Hz and better
One 2.5V, 3.3V LVDS clock output
Output enable control (positive polarity), LVCMOS/LVTTL
compatible
RMS phase jitter @ 231.25MHz (12kHz - 20MHz):
0.48ps (typical), integer PLL feedback configuration
RMS phase jitter @ 231.25MHz (1kHz - 40MHz):
0.50ps (typical), integer PLL feedback configuration
2.5V or 3.3V supply
-40°C to 85°C ambient operating temperature
Available in a lead-free (RoHS 6) 6-pin ceramic package
Block Diagram
PFD
&
LPF
FemtoClock
®
NG
VCO
1950-2600MHz
Pin Assignment
nOE 1
6 V
DD
5 nQ
4 Q
OSC
f
XTAL
2
÷P
÷N
Q
nQ
DNU 2
GND 3
÷MINT,
MFRAC
25
Configuration Register (ROM)
nOE
Pulldown
7
IDT8N4S273
6-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N4S273CCD
OCTOBER 31, 2012
1
©2012 Integrated Device Technology, Inc.
Why should small capacitors be placed close to the circuit when decoupling the power supply?
When decoupling the power supply, it is usually achieved by using a small capacitor and a large capacitor. But why must the small capacitor be as close to the circuit as possible and the wiring as sho...
Grizabella Analog electronics
Max32630 (III) - OLED screen display time
[i=s]This post was last edited by 29447945 on 2017-9-13 18:57[/i] An OLED display screen has been adjusted for a long time, and it can finally display today. I have two screens, one for SPI communicat...
29447945 DIY/Open Source Hardware
Serial communication based on stm32 code implementation
Serial communication is a very common communication method, with a small number of cables and simple operation. Let's take a look at the definition, principle and code implementation of serial communi...
Aguilera Microcontroller MCU
TOC problems encountered during NBoot
During the NBoot startup process, it is necessary to access the contents of block1 in NandFlash. The contents of block1 are the TOC of EBoot to be loaded next. How is the TOC of EBoot burned into nand...
sdx_none Embedded System
Implementation of wireless network card encryption protocol
If any of you have implemented the encryption protocols WEP WPA WAPI 802.11i for wireless network cards, please leave your contact information and ask for technical advice. Or add me on QQ: 610258988....
海洋dz Embedded System
RF power testing is that simple when explained thoroughly!
[i=s]This post was last edited by btty038 on 2019-12-19 14:16[/i]Since the birth of the first radio transmitter, engineers have been concerned about RF power measurement, and it is still a hot topic t...
btty038 RF/Wirelessly

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2159  1148  1817  2152  908  44  24  37  19  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号