EEWORLDEEWORLDEEWORLD

Part Number

Search

8N3S273LC-0131CDI

Description
LVPECL Output Clock Oscillator
CategoryPassive components    oscillator   
File Size498KB,19 Pages
ManufacturerIDT (Integrated Device Technology)
Download Datasheet Parametric View All

8N3S273LC-0131CDI Overview

LVPECL Output Clock Oscillator

8N3S273LC-0131CDI Parametric

Parameter NameAttribute value
Objectid1315780302
Reach Compliance CodeCompliant
Is SamacsysN
YTEOL0
maximum descent time0.45 ns
Frequency Adjustment - MechanicalNO
longest rise time0.45 ns
Maximum slew rate143 mA
Maximum supply voltage2.625 V
Minimum supply voltage2.375 V
maximum symmetry53/47 %
Other featuresENABLE/DISABLE FUNCTION; COMPLEMENTARY OUTPUT; DIFFERENTIAL OUTPUT
Maximum operating frequency1300 MHz
Minimum operating frequency975 MHz
Oscillator typeLVPECL
Output load50 OHM
Nominal supply voltage2.5 V
frequency stability20%
Installation featuresSURFACE MOUNT
Number of terminals6
Package body materialCERAMIC
Encapsulate equivalent codeDILCC6,.2
surface mountYES
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
physical size7.0mm x 5.0mm x 1.55mm
LVPECL Frequency-Programmable
Crystal Oscillator
IDT8N3S273
DATA SHEET
General Description
The IDT8N3S273 is a Frequency-Programmable Crystal Oscillator
with very flexible frequency programming capabilities. The device
uses IDT’s fourth generation FemtoClock® NG technology for an
optimum of high clock frequency and low phase noise performance.
The device accepts 2.5V or 3.3V supply and is packaged in a small,
lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm x 1.55mm package.
The device can be factory programmed to any frequency in the range
from 15.476MHz to 866.67MHz and from 975MHz to 1,300MHz and
supports a very high degree of frequency precision of 218Hz or
better. The extended temperature range supports wireless
infrastructure, telecommunication and networking end equipment
requirements.
Features
Fourth generation FemtoClock® NG technology
Factory-programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Frequency programming resolution is 218Hz and better
One 2.5V or 3.3V LVPECL clock output
Output enable control (positive polarity), LVCMOS/LVTTL
compatible
RMS phase jitter @ 156.25MHz (12kHz - 20MHz): 0.24ps
(typical), integer PLL feedback configuration
RMS phase jitter @ 156.25MHz (1kHz - 40MHz): 0.27ps (typical),
integer PLL feedback configuration
2.5V or 3.3V supply
-40°C to 85°C ambient operating temperature
Available in a lead-free (RoHS 6) 6-pin ceramic package
Block Diagram
PFD
&
LPF
FemtoClock® NG
VCO
1950-2600MHz
Pin Assignment
nOE
1
2
3
6
5
4
V
CC
nQ
Q
DNU
V
EE
OSC
f
XTAL
2
÷P
÷N
Q
nQ
÷MINT,
MFRAC
25
Configuration Register (ROM)
nOE
Pulldown
7
IDT8N3S273
6-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N3S273CCD
REVISION A DECEMBER 11, 2012
1
©2012 Integrated Device Technology, Inc.
Regarding the principle of flash ADC, there is a question that I don't understand
As shown in the figure, the flash ADC uses a resistor network to obtain the reference level of the comparator. But why are the resistors on the two sides not R but 1.5R and 0.5R? Doesn't this cause th...
社会实践 Analog electronics
After manually raising the software priority, can interrupts of the same priority level still occur?
When a section of code in my main program is running, I modify the software priority from Level 0 (I1=1, I0=0) to Level 1 (I1=0, I0=1), and set the priority of external port PB1 to Level 1 (I1=0, I0=1...
zyyu stm32/stm8
I just started to learn the basics of single-chip microcomputers! I want to use the C51 single-chip microcomputer to write a program code that can generate a sine wave using the assembly program
I just started to learn the basics of single-chip microcomputers! I want to use the C51 single-chip microcomputer to write a program code that can generate a sine wave using the assembly program...
21999 MCU
Help!
Are EP2C8Q208C8N and EP2C5Q208C8N compatible?...
wangjiaqi_ys FPGA/CPLD
When doing monitoring projects, the choice of power supply determines your fate
1. The surveillance camera is marked with DC12V/AC24V universal power supply. What kind of power supply should I choose? A: Choose AC24V monitoring power supply, because for the same transmission dist...
中志达摄像机 Industrial Control Electronics
About the LTC1745 Analog-to-Digital Converter
[color=blue]Today, a netizen asked for information about the LTC1745 analog-to-digital converter. I checked it out, and although I didn’t find any Chinese version, this English document provides a rel...
小娜 Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2153  1727  2205  602  1638  44  35  45  13  33 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号