PI3A4624
3.0V, SOTiny
™
0.4Ω
Single-Supply SPDT Analog Switch
Features
• Low On-Resistance: 0.4Ω (+2.7V Supply)
• R
ON
Matching: 0.09Ω Max.at 25 °C
• R
ON
Flatness: 0.1Ω Max. (+3.0V Supply) at 25 °C
• Low 2nA Input Leakage at 25 °C
• +1.5V to +3.6V Single-Supply Operation
• Fast Switching Time: 40ns Max.
• -41dB Off-Isolation at 100KHz
• TTL/CMOS Logic Compatible
• Low Power Consumption: 5µW
• Packaging (Pb-free & Green available):
– 6-pin Small Compact SOT-23 (T)
– 6-pin No Lead (TDFN) (ZC)
Description
The PI3A4624 is a single-pole, double-throw (SPDT) analog switch.
Specifications include a low ON-Resistance of 0.4Ω, and fast
switching times (40ns Max.) with 3.0V supply operation.
Specifications are given for 1.8V, 2.5V and 3.3V power supply
operation. Operating voltage range is +1.5V to +3.6V.
To minimize PC board area use, the device is available in the ultra
compact TDFN, and the small compact SOT-23, 6-pin packages.
Operating temperature range is – 40°C to 85°C.
Block Diagram, Pin Configuration
Applications
• Communication Circuits
• Cellular Phones
• Audio and Video Signal Routing
• Portable Battery-Operated Equipment
• Data Acquisition Systems
• Computer Peripherals
• Telecommunications
• Relay Replacement
• Wireless Terminals and Peripherals
• Hard Drives
• Modems
IN
1
6
NO
V
CC
2
5
COM
GND
3
4
NC
SOT23
IN
1
6
NO
Truth Table
Logic
0
1
NC
ON
OFF
NO
OFF
ON
V
CC
2
5
COM
GND
3
4
NC
TDFN
Switches shown for Logic “0” input
Top View
1
PS8712A
07/07/04
PI3A4624
3.0V, SOTiny
™
0.4Ω
Single-Supply SPDT Analog Switch
Absolute Maximum Ratings
Voltages Referenced to GND
V
CC
....................................................................... –0.5V to +3.6V
V
IN
, V
COM
, V
NC
, V
NO
CC
+0.3V
or 30mA, whichever occurs first
Current (any terminal)...................................................... ±200mA
Peak Current, COM, NO, NC
(Pulsed at 1ms, 10% duty cycle)...................................... ±400mA
(1)
.............................–0.5V to V
Thermal Information
Continuous Power Dissipation
SOT-23, 6-pin (derate 7.1mW/ºC above +70ºC) ................ 0.5W
Storage Temperature ........................................ –65ºC to +150ºC
Lead Temperature (soldering, 10s) ................................. +300ºC
Notes:
1. Signals on NC, NO, COM, or IN exceeding V
CC
or GND are clamped by internal diodes. Limit forward diode current to 30mA.
Caution:
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating
and operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied.
Electrical Specifications - Single +3.3V Supply
Parameter
Analog Switch
Analog Signal Range
(3)
On-Resistance
On-Resistance Match
Between Channels
(4)
On-Resistance Flat-
ness
(5)
NO or NC Off Leakage
Current
(6)
COM On Leakage Cur-
rent
(6)
V
ANALOG
R
ON
Symbol
(V
CC
= +3.3V ± 10%, GND = 0V, V
IH
= 1.4V, V
IL
= 0.5V)
Conditions
Package
Temp. (°C) Min.
(1)
Typ.
(2)
Max.
(1)
Units
Full
25
V
CC
= 2.7V,
I
COM
= 100mA,
V
NO
or V
NC
= +1.5V
SOT23
TDFN
Full
25
Full
V
CC
= 2.7V,
I
COM
= 100mA,
V
NO
or V
NC
= 0.8V,
2.0V
V
CC
= 3.3V,
V
COM
= 0V,
V
NO
or V
NC
= +2.0V
V
CC
= 3.3V,
V
COM
= +2.0V, V
NO
or
V
NC
= +2.0V
25
Full
25
Full
25
Full
0
V
CC
V
0.4
0.5
0.5
0.6
0.08
0.09
0.1
0.1
Ω
∆R
ON
R
FLAT(ON)
I
NO(OFF)
or
I
NC(OFF)
I
COM(ON)
–1
–10
–2
–20
1
10
2
20
nA
2
PS8712A
07/07/04
PI3A4624
3.0V, SOTiny
™
0.4Ω
Single-Supply SPDT Analog Switch
Electrical Specifications - Single +3.3V Supply
(continued)
(V
CC
= +3.3V ± 10%, GND = 0V, V
IH
= 1.4V, V
IL
= 0.5V)
Parameter
Logic Input
Input High Voltage
Input Low Voltage
Input Current with
Voltage High
Input Current with
Voltage Low
Dynamic
Turn-On-Time
Turn-Off-Time
Charge Injection
(3)
Off Isolation
(7)
CrossTalk
(8)
NC or NO
Capacitance
COM Off
Capacitance
COM On
Capacitance
Supply
Power-Supply Range
Positive Supply
Current
V
CC
I
CC
V
CC
= 3.6V, V
IN
= 0V or V
CC
1.5
Full
3.6
100
V
nA
t
ON
t
OFF
Q
O
IRR
X
TALK
C
NC/NO (OFF)
C
COM(OFF
)
C
COM(ON)
f = 1 MHz, Figure 6
25
V
CC
= 3.3V, V
NO
or V
NC
= 2.0V,
Figure 1
C
L
=1nF, V
GEN
= 0V, R
GEN
= 0Ω,
Figure 2
R
L
= 50Ω, f = 100 KHz, Figure 3
R
L
= 50Ω, f = 100 KHz, Figure 4
f = 1 MHz, Figure 5
75
200
pF
Full
25
Full
25
40
-27
-41
75
20
40
10
20
pC
dB
ns
V
IH
V
IL
I
INH
I
INL
Guaranteed Logic High Level
Guaranteed Logic LowLevel
V
IN
= 1.4V, all others = 0.5V
V
IN
= 0.5V, all others = 1.4V
–1
–1
Full
1.4
0.5
1
µA
1
V
Symbol
Conditions
Temp. (°C)
Min
.(1)
Typ.
(2)
Max.
(1)
Units
Notes:
1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet.
2. Typical values are for DESIGN AID ONLY, not guaranteed or subject to production testing.
3. Guaranteed by design.
4.
∆R
ON
= R
ON
max. - R
ON
min.
5. Flatness is defined as the difference between the maximum and minimum value of On-Resistance measured.
6. Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at +25ºC.
7. Off Isolation = 20log
10
[ V
COM
/ (V
NO
or V
NC
) ]. See Figure 4.
8. Between any two switches. See Figure 5.
3
PS8712A
07/07/04
PI3A4624
3.0V, SOTiny
™
0.4Ω
Single-Supply SPDT Analog Switch
Electrical Specifications - Single +2.5V Supply
(V
CC
= +2.5V ± 10%, GND = 0V, V
IH
= 1.4V, V
IL
= 0.5V)
Parameter
Analog Switch
Analog Signal Range
(3)
On-Resistance
On-Resistance Match
Between Channels
(4)
On-Resistance Flat-
ness
(5)
Dynamic
Turn-On-Time
Turn-Off-Time
Charge Injection
(3)
Logic Input
Input High Voltage
Input Low Voltage
Input High Current
Input Low Current
V
IH
V
IL
I
INH
I
INL
Guaranteed Logic High Level
Guaranteed Logic LowLevel
V
IN
= 1.4V, all others = 0.5V
V
IN
= 0.5V, all others = 1.4V
Full
Full
Full
Full
–1
–1
1.4
0.5
1
1
V
µA
t
ON
t
OFF
Q
25
V
CC
= 2.5V, V
NO
or V
NC
= 1.8V,
Figure 1
C
L
= 1nF, V
GEN
= 0V, R
GEN
= 0V,
Figure 2
Full
25
Full
25
40
30
50
15
30
pC
ns
V
ANALOG
R
ON
∆R
ON
R
FLAT(ON)
V
CC
= 2.5V, I
COM
= –8mA, V
NO
or V
NC
= 1.8V
V
CC
=2.5V, I
COM
= –8mA, V
NO
or
V
NC
= 0.8V, 1.8V
25
Full
25
Full
25
Full
0
V
CC
0.5
0.6
0.1
0.1
0.1
0.1
Ω
V
Symbol
Conditions
Temp. (°C)
Min.
(1)
Typ.
(2)
Max.
(1)
Units
Notes:
1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet.
2. Typical values are for DESIGN AID ONLY, not guaranteed or subject to production testing.
3. Guaranteed by design.
4. ΔR
ON
= R
ON
max. - R
ON
min.
5. Flatness is defined as the difference between the maximum and minimum value of On-Resistance measured.
4
PS8712A
07/07/04
PI3A4624
3.0V, SOTiny
™
0.4Ω
Single-Supply SPDT Analog Switch
Electrical Specifications - Single +1.8V Supply
(V
CC
= +1.8V ± 10%, GND = 0V, V
IH
= 1.4V, V
IL
= 0.5V)
Parameter
Analog Switch
Analog Signal
Range
(3)
On-Resistance
On-Resistance
Match Between
Channels
(4)
On-Resistance
Flatness
(5)
Dynamic
Turn-On-Time
Turn-Off-Time
Charge Injection
(3)
Logic Input
Input High Voltage
Input Low Voltage
Input High Current
Input Low Current
V
IH
V
IL
I
INH
I
INL
Guaranteed Logic High Level
Guaranteed Logic LowLevel
V
IN
= 1.4V, all others = 0.5V
V
IN
= 0.5V, all others = 1.4V
Full
Full
Full
Full
–1
–1
1.4
0.5
1
1
V
µA
t
ON
t
OFF
Q
25
V
CC
=1.8V, V
NO
or V
NC
= 1.5V,
Figure 1
C
L
= 1nF, V
GEN
= 0V,
R
GEN
= 0V, Figure 2
Full
25
Full
25
36
50
50
20
40
pC
ns
V
ANALOG
R
ON
∆R
ON
R
FLAT(ON)
V
CC
=1.8V, I
COM
= –4mA,
V
NO
or V
NC
= 1.5V
25
Full
25
V
CC
=1.8V, I
COM
= –4mA,
V
NO
or V
NC
= 0.8V, 1.5V
Full
25
Full
0
V
CC
0.55
0.65
0.1
0.2
0.9
1.3
Ω
V
Symbol
Conditions
Temp. (°C)
Min.
(1)
Typ.
(2)
Max.
(1)
Units
Notes:
1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet.
2. Typical values are for DESIGN AID ONLY, not guaranteed or subject to production testing.
3. Guaranteed by design.
4. ΔR
ON
= R
ON
max. - R
ON
min.
5. Flatness is defined as the difference between the maximum and minimum value of On-Resistance measured.
5
PS8712A
07/07/04
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
