Electrodes and Accessories
F03-@
CSM_F03-@_DS_E_9_6
A Wide Variety of Electrodes for Long Lasting
Reliability
• Standard Electrodes are made of stainless steel (SUS 304) and
can be used in applications for purified water.
• SUS316 Electrodes can be used in applications where resistance
to corrosion is required. Titanium and HAS Electrodes can be
used in applications where resistance to acid is required.
• For applications where long electrodes are required, a connection
nut and two Lock Nuts can be used to extend the electrodes 1 m
at a time.
Refer to
Safety Precautions for Electrodes and
Electrode Holders.
Ordering Information
Material indications are provided on all OMRON electrodes, connection nuts, and Lock Nuts.
Electrodes
Select an electrode appropriate for the type of liquid. Refer to
Technical Guide for Level Controllers.
Model
F03-01 SUS304 ELECTRODE
F03-01 SUS316 ELECTRODE
F03-01 HAS B ELECTRODE
F03-01 HAS C ELECTRODE
F03-01 TITANIUM ELECTRODE
SUS304
SUS316
N10665 (See note)
N10276 (See note)
Titanium
Approx. 195
Approx. 190
Approx. 100
Material
Weight (g)
Approx. 170
1 line
2 lines
3 lines
4 lines
5 lines
Material
indication
lines
Material indication lines
Electrodes
M6
Note:
UNS No. (Unified Numbering System No.) is an international metal designation system that specifies a unique number for each material.
Insulated Electrodes
Electrodes are insulated with a plastic sheath to prevent them from
touching each other and to isolate them from debris in the liquid.
Before application, strip back about 10 cm of the sheath at the end to
ensure sufficient conductivity.
Model
F03-01 SUS304 BINIL
F03-01 SUS304 FLUORORESIN
F03-01 SUS316 BINIL
F03-01 SUS316 FLUORORESIN
Vinyl Tubing
Fluororesin Tubing
Vinyl Tubing
Fluororesin Tubing
Sheath
Connecting Nuts
Model
F03-02 SUS304
(See note 1.)
F03-02 SUS316
(See note 1.)
F03-02 HAS B
F03-02 HAS C
F03-02 TITANIUM
Material
SUS303
(Equivalent to SUS304)
SUS316
N10665 (See note 2.)
N10276 (See note 2.)
Titanium
Approx. 6
Weight (g)
Material
indication
Approx. 12 Blank
6
Approx. 20 B
C
T
Note:
Tubing comes in 1-m lengths with a sheath thickness of
0.5 mm.
Note: 1.
Spring washers made of the same material are included
with the F03-02 SUS304 and F03-02 SUS316.
Spring washers are not included with the other models.
OMRON does not sell spring washers by themselves.
2.
UNS No. (Unified Numbering System No.) is an
international metal designation system that specifies a
unique number for each material.
1
F03-@
Electrode Sets
An Electrode Set consists of an electrode, a connecting nut, and two
Lock Nuts.
Set model
F03-60 SUS304
Components
F03-01 SUS304
ELECTRODE
F03-02 SUS304
F03-03 SUS304
F03-60 SUS316
F03-01 SUS316
ELECTRODE
F03-02 SUS316
F03-03 SUS316
No. of parts
in an set
1
1
2
1
1
2
Weight
(g)
Approx.
190
Lock Nuts
Model
F03-03 SUS304
(See note 1.)
F03-03 SUS316
(See note 1.)
F03-03 HAS B
F03-03 HAS C
F03-03 TITANIUM
Material
Weight Material
(g)
indication
SUS303
Approx. Blank
(Equivalent to SUS304) 2
SUS316
N10665
(See note 2.)
N10276
(See note 2.)
Titanium
6
Approx. B
5
C
Approx. T
2
Note:
HAS and titanium Electrodes do not come in sets.
Note: 1.
Only SUS304 and SUS316 Lock Nuts come with spring
washers made of the same material. HAS B, HAS C and
TITANIUM don’t come with spring washer.
2.
UNS No. (Unified Numbering System No.) is an internation-
al metal designation system that specifies a unique number
for each material.
Electrode Separators
When long electrodes are required, use Separators at each joint (every 1 m) to prevent the Electrodes from touching each other.
Use a 1-pole Separator with BF Electrode Holders. The five-pole model can be used with PS-5S and PS-4S Electrode Holders.
Separators cannot be used with PS-31 Electrode Holders.
Model
F03-14 1P
No. of
Dimensions Applicable
Electrodes
Electrode
Holder
1
6.5 dia.
Weight (g)
Approx. 15
Material
Ceramic
Operating
Temperature
250°C max.
Electrode
Holder
Separator
BF-@(R)
28 dia.
F03-14 3P
3
Three, 7-dia. holes
PS-3S(R)
Approx. 30
Separator
Connecting
nut
Spring
washer
20
41
Lock Nut
Connecting
nut
Lock Nut
Electrode
F03-14 5P
5
Five,
7-dia.
holes
PS-4S(R)
PS-5S(R)
Lock Nut
20
46
Note:
When using two or more Separators,
be careful with the mounting direction
of the connecting nut screws which
connect electrodes. Avoid the screws
from touching each other.
Note:
The Electrode Separators cannot be used unless the Electrodes are coupled.
Accessories (Order Separately)
Application
Protective Cover (for PS-@S and BF-3/-5)
Mounting Frame (for PS-@S)
Dust-proof Rubber Cap (for PS-31)
Model
F03-11
F03-12
F03-31
Mounting Frame for Installing in Concrete (for PS-@S(R)) F03-13
2
F03-@
Dimensions of Electrodes and Accessories
Note:
All units are in millimeters unless otherwise indicated.
Electrode
F03-01
M6 5.23 dia.
M6
Lock Nut
M6
Standa
±
on: 21
2
rd: 1 m
de
Threa
d secti
on: 21
±
2
F03-03
SUS304
SUS316
Titanium
M6
11.5
F03-03
HAS B
HAS C
5
13
10
10
5.5
Thr
secti
eaded
Connecting nut
F03-02
SUS304
SUS316
M6
10
(15) (See note 1.)
20
F03-02
HAS B
HAS C
M6
F03-02
Titanium
10
20
13
10
11.5
20
(See note 2.)
(See note 2.)
M6
Note: 1.
Dimension when mounting Electrodes.
2.
Clamp screws are not provided for HAS B, HAS C, or titanium models. F03-03 Lock Nuts are used to mount Electrodes.
■
Safety Precautions
Refer to
Safety Precautions for All Level Controllers.
■
Precautions for Correct Use
Cleaning Electrodes
Electrodes are clean when they are dispatched. In the rare occasion
that they become dirty during transit or storage, such as forming an
oil film on the surface, clean them again before using them.
Operating Environment
Use the Electrode within the ambient operating temperature range of
the Holder.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
In the interest of product improvement, specifications are subject to change without notice.
11.5
3
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See
http://www.omron.com/global/
or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
2019.7
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2019 All Right Reserved.
Embedded System
京公网安备 11010802033920号
EEWORLD
