EEWORLDEEWORLDEEWORLD

Part Number

Search

LT1332CG#PBF

Description
完全版 收发器 3/5 RS232 28-SSOP
Categorysemiconductor    The interface of IC   
File Size223KB,8 Pages
ManufacturerADI
Websitehttps://www.analog.com
Download Datasheet Parametric View All

LT1332CG#PBF Overview

完全版 收发器 3/5 RS232 28-SSOP

LT1332CG#PBF Parametric

Parameter NameAttribute value
category
MakerADI
series-
PackagePipe fittings
typetransceiver
protocolRS232
Number of drivers/receivers3/5
duplexFull Edition
data rate120KBd
Voltage - Power supply2V ~ 6V
Operating temperature0°C ~ 70°C
Installation typesurface mount type
Package/casing28-SSOP (0.209", 5.30mm wide)
Supplier device packaging28-SSOP
receiver lag400 mV
Basic product numberLT1332
LT1332
Wide Supply Range
Low Power RS232 Transceiver with
12V VPP Output for Flash Memory
FEATURES
s
s
s
s
s
s
s
s
DESCRIPTIO
s
s
s
s
s
Generates Full RS232 Signal Levels from 3V Supply
12V VPP Output Available for Flash Memory
Useful with a Wide Variety of Switching Regulators
Low Supply Current: I(V
CC
) = 1mA
Wide Supply Range: 2V
V
CC
6V
ESD Protection Over
±10kV
Operates to 120k Baud
Outputs Assume a High Impedance State When Off
or Powered Down
One
µPower
Receiver Remains Active While in
SHUTDOWN
Flowthrough Architecture Eases PC Board Layout
40µA Supply Current in SHUTDOWN
Absolutely No Latch-Up
Available in SO and SSOP Packages
The LT1332 is a 3-driver/5-receiver RS232 transceiver,
designed to be used in conjunction with a switching
regulator. The LT1332 shares the regulator’s positive
output, while charge is capacitively pumped from the
regulator’s switch pin to the negative supply. Schottky
rectifiers built into the LT1332 simplify the charge
pump design.
The LT1332/LT1109A combination shown below gener-
ates fully compliant RS232 signal levels from as little as 2V
of input supply. The switcher can deliver greater than
100mA of output current, making the LT1332 an excellent
choice for mouse driver circuits.
Advanced driver output stages operate up to 120k baud
while driving heavy capacitive loads. New ESD structures
on chip make the LT1332 resilient to multiple
±10kV
strikes, eliminating costly transient suppressors.
A shutdown pin disables the transceiver except for one
receiver which remains active for detecting incoming
RS232 signals. When shut down, the disabled drivers and
receivers assume high impedance output states.
APPLICATI
s
s
S
Notebook and Palmtop Computers
Mouse Driver Circuits
TYPICAL APPLICATI
STANDARD FLASH MEMORY VPP GENERATOR
SWITCHER
V
IN
2 AA
BATTERIES
UP TO 6V
L1**
33µH
22µF*
V
IN
SW
LT1109A-12
SW
SENSE
ON/OFF
GND
PGND
LT1332 Powered from an LT1109A Micropower Switching Regulator
Configured for Flash Memory
12V VPP
OUTPUT
+
1µF
V
+
1
24
23
22
21
20
19
18
17
16
15
14
LT1332
13
RS232
ON/OFF
LOGIC
SIDE
V
10µF
C
2
3
4
5
RS232
SIDE
6
7
8
MBRS130T3
DRIVER
INPUT
DRIVER
OUTPUT
R
L
= 3k
C
L
= 2500pF
ON/OFF
* AVX TAJE226K035
** SUMIDA CD54-330N (708-956-0666)
9
10
NC
11
12
0.1µF
LT1332 • TA01
3V
RS232
V
CC
+
22µF*
RECEIVER
OUTPUT
C
L
= 50pF
LT1332 • TA02
U
Output Waveforms
UO
UO
1
The LPC2138 P1 port connected to the 1602 LCD simulation in Pretous cannot display! !
I am building a virtual simulation platform in Proteus. When using LM1602, the sent data cannot be displayed normally. I have successfully used the same code in the P0 port of LPC2106. Because there a...
chengchuanqing Embedded System
After the layer is locked, Blt returns DDERR_SURFACEBUSY. Who returns it?
Is there any lock when executing Blt? If yes, where is it added? There is no lock in HalBlt. When the layer is locked, the Blt operation directly returns DDERR_SURFACEBUSY without entering HalBlt oper...
friday505 Embedded System
msp430 is easy to use
Still using arm?[[i]This post was last edited by shzps on 2012-5-17 17:57[/i]]...
shzps Microcontroller MCU
Design and production of "voice song request station" based on Raspberry Pi
"Open source hardware" refers to "computer and electronic hardware designed in the same way as free and open source software". Currently, the more popular open source hardware is Arduino, Raspberry Pi...
他们逼我做卧底 Robotics Development
EMC/EMI Problems in LED Power Supply Design
[color=#000]Electromagnetic compatibility (EMC) is the study of the generation, propagation and reception of unexpected electromagnetic energy in electricity, as well as the harmful effects caused by ...
qwqwqw2088 Power technology
Friends who have used ARM to do CAN data transmission, please help me
I use sensors to collect data, and after A/D conversion, I use CAN to send the processed data. [/size] [size=18px]The data I collected is converted into a data range of 0.00 to 999. I extract the valu...
hgdyulei ARM Technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1708  1169  1113  1773  2522  35  24  23  36  51 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号