SPECIFICATION CONTROL DRAWING
TITLE
Date
TWO CONDUCTOR, SHIELDED, JACKETED, FILTERLINE, ELECTROLOSS
5-5-06
THERMOCOUPLE CABLE, SPECIAL LIMITS OF ERROR
This specification sheet forms a part of the latest issue of Raychem Specification 55F.
55FB7110
Revision
B
COMPONENT WIRES -
1 of 55FA7108 (CHROMEL®, Half Tolerance)
1 of 55FA7109 (ALUMEL®, Half Tolerance)
SHIELD - SILVER-COATED COPPER
JACKET - RADIATION-CROSSLINKED,
MODIFIED CONDUCTIVE ETFE
COLOR - BLACK
CABLE CONSTRUCTION DETAILS
PART NUMBER
1/
CONDUCTOR
SIZE
(AWG)
22
SHIELD
SIZE
(AWG)
38
JACKET THICKNESS
(inch)
MINIMUM
NOMINAL
.008
OUTSIDE DIAMETER
(inch)
NOMINAL
.135
MAXIMUM
.142
MAXIMUM
WEIGHT
(lb/1000 ft)
15.5
55FB7110-22-*
.006
CABLE RATINGS AND ADDITIONAL REQUIREMENTS
TEMPERATURE RATING: 150°C
Maximum continuous conductor temperature
ACCELERATED AGING (CROSSLINKING PROOF TEST):
300 ± 3°C for 7 hours
BLOCKING: 200°C ± 3°C for 6 hours
FLAMMABILITY: 3 seconds (maximum); 3 inches (maximum);
no flaming of facial tissue
IDENTIFICATION AND COLOR STRIPING DURABILITY:
125 cycles (250 strokes) (minimum), 500 g weight
JACKET ELONGATION AND TENSILE STRENGTH:
Elongation, 50% (minimum)
Tensile Strength, 3500 lbf/in
2
(minimum)
JACKET FLAWS: Not Applicable
LOW TEMPERATURE-COLD BEND: -65°C ± 2°C for 4 hours
SHIELD COVERAGE: 85% (minimum)
VOLTAGE WITHSTAND TEST (DIELECTRIC):
Conductor to conductor and shield, 1500 volts (rms), 60 Hz
VOLTAGE WITHSTAND TEST (Post Environmental):
Not Applicable
PART NUMBER:
The "*" in the part number above shall be replaced by
color code designators except that violet shall be light
violet and the designator shall be 7L, with a slash
separating the component wire colors and a dash
separating the component wire colors from the jacket color.
The color of the CHROMEL® shall be shown first.
1/ Example: AWG 22,
Per MIL-STD-687: light violet with white stripe and light violet
with green stripe component wires;
black jacket: 55FB7110-22-7L9/7L5-0
The combination of the above thermoelements is referred to as type K per ANSI MC96.1.
EMF shall be 4.05 mV (minimum), 4.14 mV (maximum), at 100°C with reference junction at 0°C using special tolerance limits of ± 1.1°C,
and shall be performed on every length of finished cable.
CHROMEL® and ALUMEL® are federally registered trademarks of Hoskins Manufacturing Company. Alternative conductors, exhibiting
the same performance characteristics, may be substituted for one or both of the CHROMEL® and ALUMEL® conductors.
ElectroLoss is a trademark of Tyco Electronics Corporation.
Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice.
Tyco Electronics also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer.
1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681 EXCEPT AS SPECIFIED HEREIN. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE
RAYCHEM PART NUMBER, AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: “901/902...” MAY BE REPLACED BY “Axxx”.) OTHER
CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER.
DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL.
R
Wire & Cable
501 Oakside Avenue
Redwood City, CA 94063-3800
Phone: 1-800-227-8816
Fax: 1-650-361-6297
Page 1 of 1
THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.
REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID.
© 2006 Tyco Electronics Corporation. All rights reserved.
京公网安备 11010802033920号
EEWORLD
