Reuses existing twisted-pair I/O pins for compatible
fiber-optic transceiver pseudo-ECL (PECL) data.
Fiber mode automatically configures port:
— Pin or register selectable
— Disables autonegotiation and 10Base-T.
— Enables 100Base-FX remote fault signaling.
— Disables MLT-3 encoder/decoder.
— Disables scrambler/descrambler.
4
DSP based.
Compatible with
IEEE
* 802.3 10Base-T standard
for twisted-pair cable.
Half- and full-duplex operations.
Autopolarity detection and correction.
Adjustable squelch level for extended wire-length
capability (2 levels).
Interfaces with
IEEE
802.3u media independent
interface (MII) or a serial 10 Mbits/s 7-pin interface.
On-chip filtering eliminates the need for external fil-
ters.
s
s
s
s
s
s
General
s
s
100 Mbits/s Transceiver
s
s
Autonegotiation and management:
— Fast link pulse (FLP) burst generator.
— Arbitration function.
— Accepts preamble suppression.
— Operates up to 12.5 MHz.
Supports the MII station management protocol and
frame format (clause 22): basic and extended reg-
ister set.
Supports next page.
Provides status signals: receive activity, transmit
activity, full duplex, collision/jabber, link integrity,
and speed indication.
Powerdown mode for 10 Mbits/s and 100 Mbits/s .
Loopback for 10 Mbits/s and 100 Mbits/s .
Proprietary Low Power Mode (Nowire mode) for
saving power when there is not activity on Receive
side.
0.25
µm
low-power CMOS technology.
Single 3.3 V power supply operation.
25 MHz XTAL oscillator input or 25 MHz/50 MHz/
125 MHz clock input.
Compatible with RMII (standard version) and SMII
(standard version).
Compatible with
IEEE
802.3u MII (clause 22),
PCS/PMA (clause 24), PMD (clause 25), MII man-
agement, and autonegotiation (clause 28) specifi-
cations.
Selectable 5-bit code-group (PDT/PDR interface)
or 4-bit data nibbles (MII interface) input/output.
Full- or half-duplex operations.
Optional carrier integrity monitor (CIM).
Selectable carrier sense signal generation (MCRS)
asserted during either transmission or reception in
half duplex (MCRS asserted during reception only
in full duplex).
Adaptive equalization and baseline wander correc-
tion.
On-chip filtering eliminates the need for external
filters.
s
s
s
s
s
s
s
s
s
s
s
s
s
s
*
IEEE
is a registered trademark of The Institute of Electrical and
Electronics Engineers, Inc.
s
Note: Advisories are issued as needed to update product information. When using this data sheet for design purposes, please contact
your Lucent Technologies Microelectronics Group Account Manager to obtain the latest advisory on this product.
DNC3X3125
10/100 Mbits/s Ethernet Transceiver Macrocell
Advance Data Sheet
March 2000
Table of Contents
Contents
Page
Features .................................................................................................................................................................... 1
100 Mbits/s FX Transceiver ..................................................................................................................................... 1
General ................................................................................................................................................................... 1
Signal Information...................................................................................................................................................... 6
Signal Descriptions ................................................................................................................................................. 6
MII Station Management .........................................................................................................................................13
MII Interface Design ................................................................................................................................................14
Absolute Maximum Ratings.....................................................................................................................................14
Register Information ................................................................................................................................................19
Table 4. Status Signals .............................................................................................................................................8
Table 5. Clock and Reset Signals ............................................................................................................................. 9
Figure 2. I/Os of the DNC3X3125 Macrocell ............................................................................................................5
Figure 3. DNC MII Tx Logic ....................................................................................................................................15
Figure 4. DNC MII Rx Logic....................................................................................................................................15
This tutorial is developed based on the Gizwits Industrial Internet platform, industrial-grade Cat.1 DTU GC511, and Gizwits Demo APP. It uses RS-485 single-phase electricity meter to realize industria...
As the title says, the program for LaunchPad 430 G2553 to read and write EEPROM 24C02 is modified according to the official TI SLAA208C application note. Theoretically, it supports reading and writing...
A Mitsubishi Pajero car audio system had a fault phenomenon of no sound, but other functions were working normally. After checking, it was found that the power amplifier integrated circuit TA8205AH wa...
Based on "PSoC4 Experience_Lighting up LED", add LCD function to display ADC value. 1. Add LCD module and set as follows:2. Add program3. Problems The displayed numbers jump randomly: 1. Add delay --f...
[i=s] This post was last edited by xld0932 on 2019-4-15 19:36 [/i] 1. The installation steps of KEIL software are omitted. Open KEIL software, click Help->About uVision... in the menu bar, and a dialo...
1. Equipment Overview
Shell-and-tube heat exchangers are a common heat exchange device used in chemical evaporation and heating equipment. Currently, the tubesheets of shell-and-tube heat exch...[Details]
A vacuum eutectic furnace is a critical piece of equipment used in the manufacturing and processing of various materials, particularly in the fields of microelectronics and nanotechnology. One of t...[Details]
The most significant feature of IPS panels is that both electrodes are located on the same surface, unlike other LCD panels, which have electrodes arranged on top and bottom surfaces in a three-dim...[Details]
On August 25th, SK Hynix announced that it has completed development and entered mass production of its 321-layer, 2Tb QLC NAND flash memory product. This achievement marks the world's first applic...[Details]
Core point: The automotive industry chain and the humanoid robot industry have collaborative advantages in hardware, software, and scenarios. Upstream and downstream companies in the automotive ind...[Details]
According to foreign media reports, Nissan Motor has recently reached a cooperation with US battery technology company LiCAP Technologies to jointly promote the research and development of next-gen...[Details]
Since its invention in the mid-1940s, the microwave oven has evolved from a humble beginning to commercial use, entering homes in the 1960s and rapidly gaining popularity. Its basic functionality a...[Details]
In June 2014, the Ministry of Industry and Information Technology issued 4G FD-LTE licenses to China Unicom and China Telecom. Together with the 4G TD-LTE licenses issued to China Mobile, China Uni...[Details]
Pure electric vehicles, structurally speaking, have components such as a power battery. In addition to the power battery, a small battery also powers some low-voltage electrical components and even...[Details]
With the advent of the electric car era, the number of pure electric vehicles has increased significantly, but many car owners do not know how to properly maintain pure electric vehicles. In additi...[Details]
With the increasing number of new energy vehicles on the road, the deployment of supporting facilities for these vehicles has accelerated, and new energy vehicles have gradually entered the vision ...[Details]
Electric vehicles are powered by electricity, and charging is a device that supplements the vehicle's energy source. It is common to need to recharge the vehicle when driving. But can you charge th...[Details]
With the continuous development of the industrial automation industry, we are seeing an increasing number of intelligent devices using flexible, efficient, and precise robotic arms to p...[Details]
Reflow soldering is one of the most commonly used methods in electronics manufacturing, allowing for the soldering of large numbers of components in a relatively short time. However, any experience...[Details]
A multilevel inverter converts a DC signal into a multilevel staircase waveform. Instead of a straight positive-negative output waveform, the output waveform of a multilevel inverter alternates in ...[Details]