T18-2 Epoxy Encapsulated Right-Angle Sensor
Datasheet
Next Generation of Self-Contained dc-Operated Sensors
•
•
•
•
•
•
•
•
•
•
Complete family of sensors, all housed in the compact right angle 18 mm threaded housing designed for long
service life in wet environments
ECO-Lab certified chemically robust epoxy encapsulated plastic sensors for wash-down applications typically
found in the food and beverage industry
Epoxy encapsulation of electronics provides a redundant seal in addition to plastic ultrasonic weld joints for
maximum reliability in wet thermal shock environments
Permanent laser etched product marking will not wear off after repeated cleaning cycles
Food grade plastic materials used for all exposed surfaces
Hygienic shape for easier cleaning of the sensor
Powerful and bright visible red emitter beam for easy alignment and set-up
Highly visible output and dual-function power and stability indicators
Advanced ASIC technology makes sensor resistant to optical and electrical noise source
Wide operating temperature range: –40 °C to +70 °C (–40 °F to +158 °F)
WARNING: Not To Be Used for Personnel Protection
Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device
does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor
failure or malfunction can cause either an energized or de-energized sensor output condition.
Models
Integral 4-pin M12/Euro-style quick disconnect models are listed.
• To order the 2 m (6 ft) cable model, replace the suffix "-Q8" with "-2M"
• To order the 9 m (30 ft) cable model, replace the suffix "-Q8" with "-9M"
Models with a quick disconnect require a mating cordset.
Emitter Models
Visible Red Models
T18-2NAEL-Q8
T18-2NAEJ-Q8
T18-2NAES-Q8
Infrared Models
T18-2NAELIR-Q8
T18-2NAEJIR-Q8
T18-2NAESIR-Q8
Emitter
Type
Range
25 m (82 ft)
25 m (82 ft) with beam inhibit
25 m (82 ft) with adjustment
None
Output
Receiver Models
Model
T18-2VNRL-Q8
T18-2VPRL-Q8
T18-2VNRS-Q8
T18-2VPRS-Q8
Range
25 m (82 ft)
25 m (82 ft) with adjustment
Output
Complementary NPN
Complementary PNP
Complementary NPN
Complementary PNP
Polarized Retroreflective Models
Model
T18-2VNLP-Q8
T18-2VPLP-Q8
T18-2VNLPC-Q8
T18-2VPLPC-Q8
Range
6 m (19.7 ft) with BRT-84 reflector
6 m (19.7 ft) with BRT-84 reflector, with adjustment
Output
Complementary NPN
Complementary PNP
Complementary NPN
Complementary PNP
Diffuse Models
Models with Red Emitters
T18-2VNDL-Q8
T18-2VPDL-Q8
T18-2VNDS-Q8
T18-2VPDS-Q8
Models with Infrared Emitters
T18-2VNDLIR-Q8
T18-2VPDLIR-Q8
–
–
Range
750 mm (29.5 in) with adjustment
300 mm (11.8 in) with adjustment
Output
Complementary NPN
Complementary PNP
Complementary NPN
Complementary PNP
Original Document
201875 Rev. D
24 April 2020
201875
T18-2 Epoxy Encapsulated Right-Angle Sensor
Fixed Field Models
Models with Red Emitters
T18-2VNFF30-Q8
T18-2VPFF30-Q8
T18-2VNFF50-Q8
T18-2VPFF50-Q8
T18-2VNFF75-Q8
T18-2VPFF75-Q8
T18-2VNFF100-Q8
T18-2VPFF100-Q8
T18-2VNFF150-Q8
T18-2VPFF150-Q8
T18-2VNFF200-Q8
T18-2VPFF200-Q8
Models with Infrared Emitters
T18-2VNFF30IR-Q8
T18-2VPFF30IR-Q8
T18-2VNFF50IR-Q8
T18-2VPFF50IR-Q8
T18-2VNFF75IR-Q8
T18-2VPFF75IR-Q8
T18-2VNFF100IR-Q8
T18-2VPFF100IR-Q8
T18-2VNFF150IR-Q8
T18-2VPFF150IR-Q8
T18-2VNFF200IR-Q8
T18-2VPFF200IR-Q8
Range
30 mm
50 mm
75 mm
100 mm
150 mm
200 mm
Output
Complementary NPN
Complementary PNP
Complementary NPN
Complementary PNP
Complementary NPN
Complementary PNP
Complementary NPN
Complementary PNP
Complementary NPN
Complementary PNP
Complementary NPN
Complementary PNP
Installing the T18-2 Epoxy Encapsulated Right-Angle Sensor
Power Output
LED
LED *
Gain
Adjustment *
To install the T18-2 Epoxy Encapsulated Right-Angle Sensor:
1. Align the sensor as required for the application. For the most
sensitive object detection, align the sensor so that the
objects move across the sensor's axis.
2. Secure the sensor to a bracket.
3. Wire sensor as shown in the wiring diagrams.
4. Adjust the gain adjuster (sensitivity pot) if necessary.
* Applicable models
Wiring Diagrams
Emitter
Emitter with Active High Beam
Inhibit
3
1
4
Complementary NPN
Complementary PNP
brown
bu (3)
+
10–30 V DC
−
10-30V dc
+
10-30V dc
bn (1)
bk (4)
wh (2)
Load
Load
–
10–30 V dc
+
bn (1)
bu (3)
bk (4)
wh (2)
Load
Load
+
10–30 V dc
–
blue
–
Specifications
Supply Voltage
10 V dc to 30 V dc for ambient temperature ≤ 55 °C
10 V dc to 24 V dc for ambient temperature > 55 °C
Supply Current (Exclusive of Load Current)
All models except FF IR: < 16 mA
FF IR models: < 25 mA
Output Protection Circuitry
Protected against false pulse on power-up and continuous short circuit of
outputs. Short circuit protection at elevated temperature may require a
power cycle to reset.
Supply Protection Circuitry
Protected against reverse polarity and transient voltages
Output Rating
≤ 50 mA total current for ambient temperatures > 55 °C
≤ 100 mA total current through both outputs ≤ 55 °C
OFF-State Leakage Current: < 50 µA at 30 V dc
ON-State Saturation Voltage: < 1.5 V at 10 mA; < 3.0 V at 100 mA
Output Configuration
Complementary PNP or NPN by model number
Emitter LED
Visible Red on most models
Infrared 850 nm on select models
Infrared fixed-field models provide higher excess gain on green and blue
targets
Output Response Time
Response is independent of signal strength
Opposed models: 1.5 milliseconds ON, 1 millisecond OFF
Polarized Retro, and Diffuse models: 1.5 milliseconds ON, 0.75 milliseconds
OFF
Fixed Field models: 2 milliseconds ON, 2 milliseconds OFF
Delay on Power-up: 100 milliseconds; outputs do not conduct during this
time
Repeatability
Repeatability is independent of signal strength
Opposed models: 300 microseconds
Retro, Polarized Retro, and Diffuse models: 100 microseconds
Fixed Field models: 200 microseconds
Adjustments
Diffuse (DL, DS), Emitter (ES), Receiver (RS), Polarized Retroreflective (LPC)
models: Single turn sensitivity (gain) adjustment potentiometer
Emitter Beam Inhibit (EJ) models: Tie black wire to 10 to 30 V dc for beam
inhibit
Construction
Housing, M12 QD, and cover: Black or Yellow PBT polyester
Indicator light pipes: Translucent white PMMA (acrylic)
Indicator cover and gain pot driver: PBT polyester
Front window: PMMA
2
www.bannerengineering.com - Tel: + 1 888 373 6767
P/N 201875 Rev. D
T18-2 Epoxy Encapsulated Right-Angle Sensor
Indicators
Two LEDs (1 green, 1 amber)
Green Solid: Indicates power applied and sensor ready
Green flashing: Indicates marginal sensing signal
Amber solid: Indicates Pin-4 (black wire) conducting
Vibration and Mechanical Shock
All models meet Mil. Std. 202G requirements. Method 201A (Vibration;
frequency 10 to 60 Hz, max., double amplitude 0.06 in acceleration 10G).
Method 213B conditions H&I (Shock: 75G with unit operating; 100G for non-
operation)
Operating Conditions
–40 °C to +70 °C (–40 °F to +158 °F)
95% at +50 °C maximum relative humidity (non-condensing)
Environmental Rating
IEC IP67 per IEC60529
IEC IP68 per IEC60529
IP69K per DIN 40050-9
Certifications
Required Overcurrent Protection
WARNING: Electrical connections must be
made by qualified personnel in accordance with
local and national electrical codes and
regulations.
Overcurrent protection is required to be provided by end product application
per the supplied table.
Overcurrent protection may be provided with external fusing or via Current
Limiting, Class 2 Power Supply.
Supply wiring leads < 24 AWG shall not be spliced.
For additional product support, go to
www.bannerengineering.com.
Supply Wiring (AWG)
20
22
24
26
28
30
Required Overcurrent Protection (Amps)
5.0
3.0
2.0
1.0
0.8
0.5
Industrial
Control
Equipment
3TJJ
Class 2 power
UL Environmental Rating: Type 1
Chemical compatibility certified
ECOLAB is a registered trademark of Ecolab USA Inc. All rights reserved.
Performance Curves
Diffuse Models (300 mm Range)
Beam Pattern
20
15
1000
Excess Gain
BEAM PATTERN (mm)
10
5
−5
−10
−15
−20
EXCESS GAIN
0
50
10 0
15 0
20 0
25 0
30 0
35 0
40 0
0
100
10
1
DISTANCE (mm)
1
10
DISTANCE (mm)
100
1000
Diffuse Models (750 mm Range)
Beam Pattern
100
Excess Gain
50
40
30
20
10
0
10
20
30
40
50
0
100
200
300
400
BEAM PATTERN (mm)
IR 750mm
EXCESS GAIN
800
Visible 750mm
10
500
600
700
DISTANCE (mm)
1
1
10
100
1000
DISTANCE (mm)
P/N 201875 Rev. D
www.bannerengineering.com - Tel: + 1 888 373 6767
3
T18-2 Epoxy Encapsulated Right-Angle Sensor
Emitter/Receiver Models (Effective Beam Size: 15.2 mm)
Beam Pattern
1000
2000
1600
1200
800
400
0
400
800
1200
1600
2000
Excess Gain
BEAM PATTERN (mm)
EXCESS GAIN
0
5
10
15
20
25
100
10
DISTANCE (m)
1
0.1
1
10
100
DISTANCE (m)
Polarized Retroreflective Models
Beam Pattern
Excess Gain
100
60
BEAM PATTERN (mm)
40
20
0
- 20
- 40
- 60
0
1
2
3
4
5
6
EXCESS GAIN
BRT-92x92C
BRT-84
BRT-60x40C
BRT-40x19A
BRT-60x40IP
BRT-THG-2-100
10
DISTANCE (m)
1
0.01
0.1
1
10
DISTANCE (m)
Fixed Field Models - Excess Gain (Applies to both Visible Red and IR models)
Target for Excess Gain Curves use a 90% Reflective White Card
1000
1000
EXCESS GAIN
1
10
100
1000
EXCESS GAIN
100
100
10
10
1
1
1
10
100
1000
DISTANCE (mm)
T18-2FF30
Emitter Image Size: 4.0 mm square at 15 mm and 3.5 mm square at 30 mm
18% Gray Test Card: Cutoff distance will be 98% of value shown
6% Black Test Card: Cutoff distance will be 95% of value shown
DISTANCE (mm)
T18-2FF50
Emitter Image Size: 4 mm square at 25 mm and 3 mm square at 50 mm
18% Gray Test Card: Cutoff distance will be 98% of value shown
6% Black Test Card: Cutoff distance will be 95% of value shown
4
www.bannerengineering.com - Tel: + 1 888 373 6767
P/N 201875 Rev. D
T18-2 Epoxy Encapsulated Right-Angle Sensor
Fixed Field Models - Excess Gain (Applies to both Visible Red and IR models)
Target for Excess Gain Curves use a 90% Reflective White Card
1000
1000
EXCESS GAIN
100
EXCESS GAIN
100
10
10
1
1
10
100
1000
1
1 mm
(0.04")
10 mm
(0.4")
100 mm
(4")
1000 mm
(40")
DISTANCE (mm)
T18-2FF75
Emitter Image Size: 4.5 mm square at 37 mm and 4.0 mm square at 75 mm
18% Gray Test Card: Cutoff distance will be 98% of value shown
6% Black Test Card: Cutoff distance will be 92% of value shown
DISTANCE
T18-2FF100
Emitter Image Size: 4.5 mm square at 50 mm and 4.5 mm square at 100 mm
18% Gray Test Card: Cutoff distance will be 95% of value shown
6% Black Test Card: Cutoff distance will be 90% of value shown
1000
1000
EXCESS GAIN
10
EXCESS GAIN
10 mm
(0.4")
100 mm
(4")
1000 mm
(40")
100
100
10
1
1 mm
(0.04")
1
1 mm
(0.04")
10 mm
(0.4")
100 mm
(4")
1000 mm
(40")
DISTANCE
T18-2FF150
Emitter Image Size: 5 mm square at 75 mm and 8 mm square at 150 mm
18% Gray Test Card: Cutoff distance will be 90% of value shown
6% Black Test Card: Cutoff distance will be 70% of value shown
DISTANCE
T18-2FF200
Emitter Image Size: 5 mm square at 100 mm and 8 mm square at 200 mm
18% Gray Test Card: Cutoff distance will be 85% of value shown
6% Black Test Card: Cutoff distance will be 60% of value shown
Dimensions
All measurements are listed in millimeters [inches], unless noted otherwise.
P/N 201875 Rev. D
www.bannerengineering.com - Tel: + 1 888 373 6767
5
京公网安备 11010802033920号
EEWORLD
