DG41_C_ ..............................................................0°C to +70°C
DG41_D_ ...........................................................-40°C to +85°C
DG41_AK_ .......................................................-55°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Note 1:
Signals on S, D, or IN exceeding V+ or V- are clamped by internal diodes. Limit forward current to maximum
current rating.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Before, I said that the SW-EK-TM4C123GXL-1.0.exe software package cannot be run on the EK-LM4F120XL (i.e. Stellaris LaunchPad) board. I meant in the CCS environment, because the video is CCS, so natur...
The subject our teacher gave us is to design a low-frequency amplifier with 8-channel audio signal input, single-chip control switching, single-chip control gain, and intelligent signal amplification ...
[i=s]This post was last edited by ieee_kirito on 2016-7-25 20:56[/i] I am a junior in college and I need opa277 and opa2277 op amps to participate in the Electronic Innovation Competition. However, th...
A good SD card / MMC card learning video tutorial, AVR microcontroller driver , the online video is not so clear and the content is large, so it is not uploaded. Please watch it online first. Iwill up...
I came into contact with Texas Instruments' MSP430 in the first half of 2011. Although people around me didn't know much about TI MCU at that time, I had a lot of fun learning it. I first saw the MSP4...
I am planning to make a 2-60V adjustable power supply with a maximum current of 10A and a ripple of <100mv. Does anyone have any suggestions for me? Although I have made power supplies before, I have ...
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
The most important components of new energy electric vehicles are power batteries, electric motors and energy conversion control systems. The power battery must achieve high performance such as fas...[Details]
UDN2916LB is a two-phase stepper motor bipolar driver integrated circuit launched by SANKEN. It can drive dual-winding bipolar stepper motors and is particularly suitable for controlling dual-step ...[Details]
High specific energy lithium/thionyl chloride (Li/SOCl2) batteries are widely used in multi-functional intelligent meters (such as smart meters, water meters, etc.) as real-time clocks and memory b...[Details]
According to the National Shipbuilding Industry Economic Research Center, the total shipbuilding capacity in my country last year was about 9×106t. The new ship orders exceeded 17×106t, accounting ...[Details]
1. Introduction
Diesel engine test is the last key process in the diesel engine production process, which plays a very important role in the manufacturing quality of diesel engines. Its main c...[Details]
In recent years, information technology based on microelectronics and computer technology has developed rapidly, and ultrasonic non-destructive testing instruments have also gained unpreceden...[Details]
1. Architecture and operation of electronic toll collection system
The basic principle of the electronic toll collection system is to enable a special device (on-board unit) installed on t...[Details]
1 Introduction
In recent years, the application of LED display screens has developed rapidly, promoting the progress of LED driver ICs. Based on the high reliability of LEDs and the consistenc...[Details]
As the trend towards miniaturization continues, new packaging methods and methods of interconnecting integrated circuits have been developed. Today, "system on chip" refers to a packaging method th...[Details]
0 Introduction
In 2008, the Science and Technology Olympics is a very important aspect, and the timing and scoring system is of utmost importance in the competition. It can be said that a good...[Details]
The following text is only about the modulation algorithm of Bluetooth technology. I think it is enough to add the Bluetooth module to the microcontroller, and it is not necessary to implement the ...[Details]
CAN (Controller Area Network) is a serial communication network that effectively supports distributed control and real-time control. It has the advantages of high reliability, low cost, flexible confi...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
