E_T-1W & F_T-1W
Series
1W, FIXED INPUT, ISOLATED & UNREGULATED
DUAL/SINGLE OUTPUT DC-DC CONVERTER
multi-country patent protection
RoHS
FEATURES
Small Footprint
SMD Package Style
3KVDC Isolation
Temperature Range: -40
°
C to +85
°
C
No Heat sink Required
Industry Standard Pinout
Internal SMD construction
No External Component Required
RoHS Compliance
PRODUCT PROGRAM
Input
Part
Number
F0303T-1W
F0305T-1W
F0505T-1W
F0509T-1W
F0512T-1W
F0515T-1W
E0505T-1W
E0509T-1W
E0512T-1W
5
4.5-5.5
Voltage (VDC)
Nominal
3.3
Range
3.0-3.6
Voltage
(VDC)
3.3
5
5
9
12
15
±5
±9
±12
±15
5
9
12
12
10.8-13.2
15
±5
±9
±12
±15
Output
Current (mA)
Max
304
200
200
110
84
66
±100
±55
±42
±33
200
110
84
66
±100
±55
±42
±33
Min
30
20
20
11
9
7
±10
±6
±5
±4
20
11
9
7
±10
±6
±5
±4
73
75
70
76
78
79
71
77
78
79
69
73
73
74
71
73
74
75
UL
UL
UL
UL
UL
UL
UL
UL
UL
UL
UL
UL
UL
UL
UL
UL
Efficiency
Certificate
(%, Typ.)
APPLICATIONS
The E_T-1W&F_T-1W Series are specially
designed for applications where a group of
polar power supplies are isolated from the
input power supply in a distributed power
supply system on a circuit board.
These products apply to:
1) Where the voltage of the input power
supply is fixed (voltage variation
≤ ±10%);
2) Where isolation is necessary between
input
and
output
(isolation
voltage
≤3000VDC);
3) Where the regulation of the output
voltage and the output ripple noise are not
demanding.
Such as: purely digital circuits, ordinary low
frequency analog circuits, and IGBT power
device driving circuits.
E0515T-1W
F1205T-1W
F1209T-1W
F1212T-1W
F1215T-1W
E1205T-1W
E1209T-1W
E1212T-1W
E1215T-1W
Note: The E_T-W2/F_T-W2 series also are available in our company.
ISOLATION SPECIFICATIONS
Item
Isolation voltage
Isolation resistance
Test Conditions
Tested for 1 minute and 1mA max
Test at 500VDC
Min
3000
1000
Typ
Max
Units
VDC
MΩ
OUTPUT SPECIFICATIONS
Item
Output power
Test Conditions
For Vin change of 1%(3.3V output)
For Vin change of 1%(Others output)
10% to 100% load 3.3V output
15
12.8
8.3
6.8
6.3
10% to 100% load 5V output
Load regulation
10% to 100% load 9V output
10% to 100% load 12V output
10% to 100% load 15V output
Output voltage accuracy
Temperature drift
Output ripple &Noise*
100% full load
20MHz
Bandwidth
E_T-1W series
F_T-1W series
50
75
100
Min
0.1
Typ.
Max
1
±1.5
±1.2
20
15
10
10
10
0.03
75
100
%/°C
mVp-p
KHz
%
Units
W
MODEL SELECTION
Rated Power
Package Style
Output Voltage
Input Voltage
Product Series
Line regulation
See tolerance envelope graph
MORNSUN Science& Technology co.,Ltd.
Address: 2th floor 6th building, Huangzhou
Industrial District, Guangzhou, China
Tel: 86-20-38601850
Fax:86-20-38601272
Http://www.mornsun-power.com
Switching frequency
Full load, nominal input
*Test ripple and noise by
“parallel
cable” method. See detailed operation instructions at Testing of Power
Converter section, application notes.
Note:
1. All specifications measured at T
A
=25°C, humidity<75%, nominal input voltage and rated output load
unless otherwise specified.
2. See below recommended circuits for more details.
Specifications subject to change without notice.
F_T-1W &E_T-1W
A/1-2008
Page 1 of 2
MORNSUN reserves the copyright
COMMON SPECIFICATIONS
Item
Storage humidity
Operating temperature
Storage temperature
Temp. rise at full load
Lead temperature
Cooling
Package material
Short circuit protection*
MTBF
Weight
*Supply voltage must be discontinued at the end of short circuit duration.
APPLICATION NOTE
Min
-40
-55
15
Typ
Max
95
85
125
25
260
Free air convection
Epoxy Resin(UL94-V0)
1
3500
1.71
Second
K hours
g
Recommended testing circuit
If you want to further decrease the input/output ripple,
an
“LC”
filtering network may be connected to the input
and output ends of the DC/DC converter, see (Figure 1).
Dual O utput
Vin
Cin
L
L
Test Conditions
Units
%
Requirement on output load
To ensure this module can operate efficiently and
reliably, During operation, the minimum output load is
not less than 10%
of the full load, and that
this product
°C
should never be operated under no load!
If the actual
output power is very small, please connect a resistor with
proper resistance at the output end in parallel to increase
the load, or use our company’s products with a lower
rated output power (E _T-W2/F_T-W2 Series).
1.5mm from case for 10 seconds
TYPICAL CHARACTERISTICS
+Vo
Cout
DC DC
GND
Single Output
L
L Cout
0V
-Vo
L
Vin
Cin
+Vo
Cout
DC DC
GND
0V
(Figure 1)
It should also be noted that the inductance and the
frequency of the
“LC”
filtering network should be
Operating Temp.( C)
o
staggered with the DC/DC frequency to avoid mutual
interference. However, the capacitance of the output filter
capacitor must be proper. If the capacitance is too big, a
startup problem might arise. For every channel of output,
provided the safe and reliable operation is ensured, the
greatest capacitance of its filter capacitor sees (Table 1).
EXTERNAL CAPACITOR TABLE (Table 1)
RECOMMENDED REFLOW SOLDERING PROFILE
250
Te mperatur e (
o
C)
200
150
100
50
0
Time (s ec . )
90 Sec Max
( >220
o
C )
26 0
o
C
1 0 Sec Max
220 C
o
Vin
(VDC)
3.3/5
12
-
-
Cin
(uF)
4.7
2.2
-
-
Single
Vout
(VDC)
5
9
12
15
Cout
(uF)
10
4.7
2.2
1
Dual
Vout
(VDC)
±3.3/5
±9
±12
±15
Cout
(uF)
4.7
2.2
1
1
OUTLINE DIMENSIONS & FOOTPRINT DETAILS
First Angle Projection
RECOMMENDED FOOTPRINT
Top
view,grid:2.54*2.54mm(0.1*01inch)
7.50
(0.295)
11.20
(0.441)
1211 10
8 7
Top View
Sigle/Dual output
It’s not recommended to connect any external capacitor in
the application field with less than 0.5 watt output.
Output Voltage Regulation and Over-voltage
Protection Circuit
The simplest device for output voltage regulation,
over-voltage and over-current protection is a linear
voltage regulator with overheat protection that is
connected to the input or output end in series (Figure2).
Dual O u tput
Vi n
GND
R EG
REG
2.00
(0.079)
8
7
2.54
(0.100)
0.60
(0.024)
12 11 10
+Vout
0V
DC DC
REG
-Vout
6.50
(0.254)
6.25
(0.244)
Side View
4.25
(0.166)
FOOTPRINT DETAILS
Pin
1
2
Single
GND
Vin
0V
NC
8
+Vo
Others
NC
NC:No Connection
(0.039)
Single O utput
Vi n
R EG
REG
+Vout
1.30
Dual
GND
Vin
0V
-Vo
+Vo
NC
GND
DC DC
0V
(Figure2)
Overload Protection
Under normal operating conditions, the output circuit of
these products has no protection against overload. The
simplest method is to connect a self-recovery fuse in
series at the input end or add a circuit breaker to the
circuit.
No parallel connection or plug and play.
Note:
Unit:mm(inch)
Pin section:0.50*0.30mm(0.020*0.012inch)
Pin section tolerances: 0.10mm( 0.004inch)
General tolerances: 0.15mm( 0.006inch)
MORNSUN reserves the copyright
Specifications subject to change without notice.
F_T-1W &E_T-1W
A/1-2008
Page 2 of 2
Power technology
京公网安备 11010802033920号
EEWORLD
