The AS7C1026B is a high-performance CMOS 1,048,576-bit Static Random Access Memory (SRAM) device organized as 65,536 words ×
16 bits. It is designed for memory applications where fast data access, low power, and simple interfacing are desired.
Equal address access and cycle times (t
AA
, t
RC
, t
WC
) of 10/12/15/20 ns with output enable access times (t
OE
) of 5, 6, 7, 8 ns are ideal for
high-performance applications.
When CE is high, the device enters standby mode. If inputs are still toggling, the device will consume I
SB
power. If the bus is static, then full
standby power is reached (I
SB1
). For example, the AS7C1026B is guaranteed not to exceed 55 mW under nominal full standby conditions.
A write cycle is accomplished by asserting write enable (WE) and chip enable (CE). Data on the input pins I/O0 through I/O15 is written on
the rising edge of WE (write cycle 1) or CE (write cycle 2). To avoid bus contention, external devices should drive I/O pins only after
outputs have been disabled with output enable (OE) or write enable (WE).
A read cycle is accomplished by asserting output enable (OE) and chip enable (CE) with write enable (WE) high. The chip drives I/O pins
with the data word referenced by the input address. When either chip enable or output enable is inactive or write enable is active, output
drivers stay in high-impedance mode.
The device provides multiple center power and ground pins, and separate byte enable controls, allowing individual bytes to be written and
read. LB controls the lower bits, I/O0 through I/O7, and UB controls the higher bits, I/O8 through I/O15.
All chip inputs and outputs are TTL-compatible, and operation is from a single 5 V supply. The device is packaged in common industry
standard packages.
Absolute maximum ratings
Parameter
Voltage on V
CC
relative to GND
Voltage on any pin relative to GND
Power dissipation
Storage temperature (plastic)
Ambient temperature with VCC
applied
DC current into outputs (low)
Symbol
V
t1
V
t2
P
D
T
stg
T
bias
I
OUT
Min
–0.50
–0.50
–
–65
–55
–
Max
+7.0
V
CC
+0.50
1.0
+150
+125
20
Unit
V
V
W
°C
°C
mA
Note: Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and func-
tional operation of the device at these or any other conditions outside those indicated in the operational sections of this specification is not implied. Exposure
to absolute maximum rating conditions for extended periods may affect reliability.
Truth table
CE
H
L
L
L
L
L
L
L
L
WE
X
H
H
H
L
L
L
H
X
OE
X
L
L
L
X
X
X
H
X
LB
X
L
H
L
L
L
H
X
H
UB
X
H
L
L
L
H
L
X
H
I/O0–I/O7
High Z
D
OUT
High Z
D
OUT
D
IN
D
IN
High Z
High Z
I/O8–I/O15
High Z
High Z
D
OUT
D
OUT
D
IN
High Z
D
IN
High Z
Mode
Standby (I
SB
), I
SBI
)
Read I/O0–I/O7 (I
CC
)
Read I/O8–I/O15 (I
CC)
Read I/O0–I/O15 (I
CC
)
Write I/O0–I/O15 (I
CC
)
Write I/O0–I/O7 (I
CC
)
Write I/O8–I/O15 (I
CC
)
Output disable (I
CC
)
Key:
H = high, L = low, X = don’t care.
3/26/04, v 1.3
Alliance Semiconductor
P. 2 of 10
AS7C1026B
®
Recommended operating conditions
Parameter
Supply voltage
Input voltage
Ambient operating temperature
commercial
industrial
Symbol
V
CC
V
IH
V
IL
T
A
T
A
Min
4.5
2.2
–0.5
0
–40
Nominal
5.0
–
–
–
–
Max
5.5
V
CC
+ 0.5
0.8
70
85
Unit
V
V
V
o
o
C
C
V
IL
min = -1.0V for pulse width less than 5ns
V
IH
max = V
CC
+2.0V for pulse width less than 5ns.
DC operating characteristics (over the operating range)
1. IO Control of ADuCM360
1. It has 8 P0 ports, 8 P1 ports and 3 P2 ports. These ports havepull-up resistors that can provide 1mA current and are controlled by the GPxPUL register.
When used as input
...
[b][font=Arial][size=2]Unique High Efficiency Isolated[/size][/font] DC/DC Converter Reference Design for Ultra-Low Power and Low Power Applications[/b] [b][/b][b][size=5][/size][/b] [b][font=Arial][s...
Semiconductor manufacturers are placing greater demands on automatic test equipment (ATE) companies to quickly and reliably design test systems that meet the growing demand for ICs, with minimal incre...
[i=s]This post was last edited by yueyuanque on 2014-5-4 22:54[/i] 1. Before establishing the connection, the weekly plan had submitted the implementation of BLE Device Monitor with the help of USB Do...
I need to use a force sensor to measure the force of my finger, collect the sensor data, and display it. What kind of force sensor do you recommend? How to display it? Thank you!...
ADI Reference Circuit
京公网安备 11010802033920号
EEWORLD
