TJA1054T/S900 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Wireless rf/communication> Telecom circuit> TJA1054T/S900

TJA1054T/S900: DescriptionNetwork controller and processor IC tja1054t/s900; CategoryWireless rf/communication Telecom circuit; File Size123KB，25 Pages; ManufacturerNXP; Websitehttps://www.nxp.com

Download Datasheet Parametric Compare View All

TJA1054T/S900 Overview

Network controller and processor IC tja1054t/s900

TJA1054T/S900 Parametric

Parameter Name	Attribute value
Parts packaging code	SOIC
package instruction	SOP,
Contacts	14
Reach Compliance Code	unknown
JESD-30 code	R-PDSO-G14
length	8.65 mm
Number of functions	1
Number of terminals	14
Package body material	PLASTIC/EPOXY
encapsulated code	SOP
Package shape	RECTANGULAR
Package form	SMALL OUTLINE
Certification status	Not Qualified
Maximum seat height	1.75 mm
Nominal supply voltage	5 V
surface mount	YES
Telecom integrated circuit types	INTERFACE CIRCUIT
Terminal form	GULL WING
Terminal pitch	1.27 mm
Terminal location	DUAL
width	3.9 mm
Base Number Matches	1

Preview

Download Datasheet

View All

TJA1054

Fault-tolerant CAN transceiver

Rev. 04 — 24 September 2009

Product data sheet

1. General description

The TJA1054 is the interface between the protocol controller and the physical bus wires in

a Controller Area Network (CAN). It is primarily intended for low-speed applications up to

125 kBd in passenger cars. The device provides differential receive and transmit

capability but will switch to single-wire transmitter and/or receiver in error conditions.

The TJA1054T is pin and downwards compatible with the PCA82C252T and the

TJA1053T. This means that these two devices can be replaced by the TJA1054T with

retention of all functions.

The most important improvements of the TJA1054 with respect to the PCA82C252 and

TJA1053 are:

•

Very low EME due to a very good matching of the CANL and CANH output signals

Good EMI, especially in low power modes

Full wake-up capability during bus failures

Extended bus failure management including short-circuit of the CANH bus line to V

Support for easy system fault diagnosis

Two-edge sensitive wake-up input signal via pin WAKE

2. Features

2.1 Optimized for in-car low-speed communication

Baud rate up to 125 kBd

Up to 32 nodes can be connected

Supports unshielded bus wires

Very low ElectroMagnetic Emission (EME) due to built-in slope control function and a

very good matching of the CANL and CANH bus outputs

Very high ElectroMagnetic Immunity (EMI) in normal and low power operating modes

Fully integrated receiver ﬁlters

Transmit Data (TxD) dominant time-out function

2.2 Bus failure management

Supports single-wire transmission modes with ground offset voltages up to 1.5 V

Automatic switching to single-wire mode in the event of bus failures, even when the

CANH bus wire is short-circuited to V

Automatic reset to differential mode if bus failure is removed

Full wake-up capability during failure modes

NXP Semiconductors

TJA1054

Fault-tolerant CAN transceiver

7. Functional description

The TJA1054 is the interface between the CAN protocol controller and the physical wires

of the CAN bus (see

Figure 7).

It is primarily intended for low-speed applications, up to

125 kBd, in passenger cars. The device provides differential transmit capability to the

CAN bus and differential receive capability to the CAN controller.

To reduce EME, the rise and fall slopes are limited. This allows the use of an unshielded

twisted pair or a parallel pair of wires for the bus lines. Moreover, the device supports

transmission capability on either bus line if one of the wires is corrupted. The failure

detection logic automatically selects a suitable transmission mode.

In normal operating mode (no wiring failures) the differential receiver is output on pin RXD

(see

Figure 1).

The differential receiver inputs are connected to pins CANH and CANL

through integrated ﬁlters. The ﬁltered input signals are also used for the single-wire

receivers. The receivers connected to pins CANH and CANL have threshold voltages that

ensure a maximum noise margin in single-wire mode.

A timer function (TxD dominant time-out function) has been integrated to prevent the bus

lines from being driven into a permanent dominant state (thus blocking the entire network

communication) due to a situation in which pin TXD is permanently forced to a LOW level,

caused by a hardware and/or software application failure.

If the duration of the LOW level on pin TXD exceeds a certain time, the transmitter will be

disabled. The timer will be reset by a HIGH level on pin TXD.

7.1 Failure detector

The failure detector is fully active in the normal operating mode. After the detection of a

single bus failure the detector switches to the appropriate mode (see

Table 4).

The

differential receiver threshold voltage is set at

−3.2

V typical (V

= 5 V). This ensures

correct reception with a noise margin as high as possible in the normal operating mode

and in the event of failures 1, 2, 5 and 6a. These failures, or recovery from them, do not

destroy ongoing transmissions. The output drivers remain active, the termination does not

change and the receiver remains in differential mode (see

Table 4).

Failures 3, 3a and 6 are detected by comparators connected to the CANH and CANL bus

lines. Failures 3 and 3a are detected in a two-step approach. If the CANH bus line

exceeds a certain voltage level, the differential comparator signals a continuous dominant

condition. Because of inter operability reasons with the predecessor products

PCA82C252 and TJA1053, after a ﬁrst time-out the transceiver switches to single-wire

operation through CANH. If the CANH bus line is still exceeding the CANH detection

voltage for a second time-out, the TJA1054 switches to CANL operation; the CANH driver

is switched off and the RTH bias changes to the pull-down current source. The time-outs

(delays) are needed to avoid false triggering by external RF ﬁelds.

TJA1054_4

Product data sheet

Rev. 04 — 24 September 2009

5 of 25

TJA1054T/S900 Related Products

	TJA1054T/S900	TJA1054T
Description	Network controller and processor IC tja1054t/s900	LIN bus transceiver chip
Parts packaging code	SOIC	SOIC
package instruction	SOP,	SOP, SOP14,.25
Contacts	14	14
Reach Compliance Code	unknown	unknown
JESD-30 code	R-PDSO-G14	R-PDSO-G14
length	8.65 mm	8.65 mm
Number of functions	1	1
Number of terminals	14	14
Package body material	PLASTIC/EPOXY	PLASTIC/EPOXY
encapsulated code	SOP	SOP
Package shape	RECTANGULAR	RECTANGULAR
Package form	SMALL OUTLINE	SMALL OUTLINE
Certification status	Not Qualified	Not Qualified
Maximum seat height	1.75 mm	1.75 mm
Nominal supply voltage	5 V	5 V
surface mount	YES	YES
Telecom integrated circuit types	INTERFACE CIRCUIT	INTERFACE CIRCUIT
Terminal form	GULL WING	GULL WING
Terminal pitch	1.27 mm	1.27 mm
Terminal location	DUAL	DUAL
width	3.9 mm	3.9 mm

Recommended Resources

Boiler control circuit

HT-1391 circuit

Photoelectric amplifier circuit used on CNC wire cutting machine

Electricity signal revolution acquisition circuit

EKG amplification circuit

Computer motherboard circuit diagram 815 3_36

Wuhan Optics Valley recruits hardware engineers (2 positions): Wuhan Optics Valley is recruiting hardware engineers (2 positions) Hardware Engineers Office Location: Wuhan Optics Valley International Enterprise Center Salary: 5,000 yuan and above, five insurances...; nsr_500 Recruitment

Introduction to STM32H7 Nucleo: The development board of STM32H7 series is here, model is NUCLEO-H743ZI, Nucleo-144 series.You can go here to have a look: [url]http://www.st.com/content/st_com/en/products/evaluation-tools/product-ev...; cz0842 stm32/stm8

Murata Tmall flagship store officially opened: 20% off on all items in the first month of opening!: Murata Manufacturing Co., Ltd. (hereinafter referred to as "Murata"), a comprehensive electronic component manufacturer that creates advanced technologies and components, has opened a flagship store o...; eric_wang Integrated technical exchanges

What's up with all these distractions?: By Tony Calabria Texas Instruments When designing with a digital-to-analog converter (DAC), you want the output to transition monotonically from one value to another, but real circuits don't always wo...; qwqwqw2088 Analogue and Mixed Signal

High score!! Please help me find the mistakes: This is a program for a lower computer (89c52). The lower computer and the upper computer communicate through the serial port. When the upper computer sends character a, the lower computer sends the s...; ljysyn Embedded System

Long queues for tickets in the snow: On January 18, passengers queued in the snow at Hefei Railway Station in Anhui Province to wait for entry to the station.On January 18, passengers queued in the snow outside the centralized ticket off...; maylove Talking

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components