25Amps
Single Phase Silicon Bridge
KBPC2500~2510
Description
KBPC
Features
Mechanical Data
Case: Metal case
Surge overload ratings to 300 amperes
Terminals: Plated .25" (6.53mm) Faston
This series is UL listed under the Recognized
Mounting Position: Bolt down on heat-sink with silicone thermal
Component Index, file number E142814
compound between bridges and mounting surface for
The plastic material used carries Underwriters Laboratory maximum heat transfer efficiency
flammability recognition 94V-0
Mounting Position: Any
Universal 4-way terminals, snap-on, wrap-around,
Weight: 1.024 ounce, 29 grams (approx)
solder or P.C. Board mounting
High temperature soldering guaranteed 265 C/10
seconds at 5 lbs (2.3kg) tension
Maximum Ratings & Thermal Characteristics
Rating at 25 C ambient temperature unless otherwise specified, Resistive or Inductive load, 60 Hz.
For Capacitive load derate current by 20%.
KBPC KBPC KBPC KBPC KBPC KBPC KBPC
Parameter
Symbol
2500 2501 2502 2504 2506 2508 2510
unit
V
RRM
50
100
200
400
600
800
1000 V
Maximum repetitive peak reverse voltage
Maximum RMS bridge input voltage
Maximum DC blocking voltage
Maximum average forward rectified
output current at T
A
=55 C
Peak forward surge current single sine-wave
superimposed on rated load (JEDEC Method)
Rating for fusing ( t<8.3ms)
Typical thermal resistance per element
(1)
Isolation voltage from case to leads
Operating junction and storage temperature
range
V
RMS
V
DC
I
F(AV)
I
FSM
I t
R
eJA
V
IS
T
J
,
T
STG
2
35
50
70
100
140
200
280
400
25
300
374
2.1
2500
420
600
560
800
700
1000
V
V
A
A
A
sec
C/W
Vac
2
-55 to + 150
Electrical Characteristics
Rating at 25 C ambient temperature unless otherwise specified. Resistive or Inductive load, 60Hz.
For Capacitive load derate by 20 %.
KBPC KBPC KBPC KBPC KBPC KBPC KBPC
Parameter
Symbol
2500 2501 2502 2504 2506 2508 2510
Unit
Maximum instantaneous forward voltage drop
per leg at 12.5A
Maximum DC reverse current at rated T
A
=25 C
DC blocking voltage per element
T
A
=125 C
V
F
I
R
1.0
10
500
V
A
Notes:
(1)Thermal resistance from Junction to Ambemt on P.C.board mounting.
25Amps
Single Phase Silicon Bridge
Rating and Characteristic Curves
( TA=25
C
Unless otherwise noted )
KBPC2500 thru KBPC2510
o
Fig. 1 Derating Curve for
Output Rectified Current
30
Fig. 2 Maximum Non-repetitive Peak
Forward Surge Current
Peak Forward Surge Current,
Amperes
400
300
200
8.3ms
Single half-sine-Wave
[JEDEC Method]
Average Forward Output
Current, Amperes
20
10
60Hz Resistive or
Inductive Load
0
0
50
100
o
100
150
40
1
10
100
Case Temperature, C
Number of Cycles at 60HZ
Fig. 3 Typical Instantaneous
Forward Characteristics
100
10
Fig. 4 Typical Reverse
o
Characteristics at Tj=25 C
Instantaneous Reverse
Current ,Amperes
Instantaneous Forward Current,
Amperes
Tj=100 C
10
1.0
1.0
0.1
0.1
Tj=25 C
Pulse Width=300us
2% duty cycle
Tj=25 C
.01
.01
0.4
0.6
0.8
1.0
1.2
1.4
1.6
0
20
40
60
80
100
120
140
Instantaneous Forward
Voltage, Volts
Percent of Rated Peak Reverse
Voltage, %
25Amps
Single Phase Silicon Bridge
KBPC2500~2510
Ratings at
25 Deg. C ambient
temperature
unless otherwise
specified.
Single Phase Half
Wave, 60 HZ
Resistive or
Inductive Load.
For Capacitive
Load, Derate
Current by 20%.
NOTES:
1. Corrosion-Resistant Terminals Designed for .250" Female Quick Connect Wrap Around
or Solder.
2. A Thin Film of Silicone Thermal Compound is Recommended Between Bridge and
Mounting Surface for Improved Thermal Conduction.
3. These FCI Bridges Are Also Available in Fast Recovery, In Positive and Negative Center
Tap and in Double Configurations. Consult with FCI for Your Special Requirements.
25Amps
Single Phase Silicon Bridge
KBPC2500~2510
Case - Metal or Molded Plastic
AC In
Terminals - Plated .25" Faston or Plated Copper Wire
Leads .040" Diameter
Weight - 0.706 Ounces, 20 Grams
DC Out
Mounting Position - Any with Bolt Down with Silicone
Thermal Compound Between Bridge and
Mounting Surface for Optimum Heat
Transfer
Mounting Torque - 20 Inch Pound Max
Ordering Information
FCIS KBPC Series of Bridges Can Be Ordered with Options on Terminals and Case Materials.
How To Specify Case Material and Terminal Options:
n
For Metal Case, Order Suffix
(1) M
n
For Plastic Case, Order Suffix
(1) P
n
For Faston Terminals, Order Suffix
(2) F
n
For Wire Lead Terminals, Order Suffix
(2) W
KBPC Series Examples
To Order a 25 Amp, 400 Volt Bridge with Faston Leads and a Plastic Case:
Specify -
KBPC2504PF
. . . Where
P = Plastic
and
F = Faston Terminals
To Order a 35 Amp, 800 Volt Bridge with Wire Leads and a Metal Case:
Specify -
KBPC3508MW
. . . Where
M = Metal
and
W = Wire Leads
(Terminals)
To Order a 15 Amp, 200 Volt, UL Recognized Bridge with Wire Leads and a Plastic Case:
Specify -
KBPC1502PWU
. . . Where
P = Plastic
and
W = Wire Leads
(Terminals) and
U = UL Recognized
NOTE:
Fast Recovery Bridges (Diodes) Are Available; Please Contact FCI Components.
KBPC - S Series Examples
To Order Bridges with the In-Line Pin Configuration, Select the Current and Voltage Desired and Add
S
as the Suffix, as
shown in the following example.
To Order a 35 Amp, 800 Volt Bridge with In-Line Wire Leads:
Specify -
KBPC3508S
. . . Where
S = In-Line Wire Lead Terminals
京公网安备 11010802033920号
EEWORLD
