PDU108H
3-BIT, ECL-INTERFACED
PROGRAMMABLE DELAY LINE
(SERIES PDU108H)
FEATURES
•
•
•
•
•
Digitally programmable in 8 delay steps
Monotonic delay-versus-address variation
Precise and stable delays
Input & outputs fully 10KH-ECL interfaced & buffered
Fits standard 16-pin DIP socket
GND
ENB
1
2
16
15
data
3
®
delay
devices,
inc.
PACKAGES
GND
OUT
IN
A0
VEE
6
7
8
10
9
A1
A2
GND
ENB
N/C
N/C
N/C
IN
A0
VEE
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
GND
OUT
N/C
N/C
N/C
N/C
A1
A2
PDU108H-xx DIP
PDU108H-xxM Military DIP
PDU108H-xxC3 SMD
PDU108H-xxMC3 Mil SMD
FUNCTIONAL DESCRIPTION
The PDU108H-series device is a 3-bit digitally programmable delay line.
The delay, TD
A
, from the input pin (IN) to the output pin (OUT) depends on
the address code (A2-A0) according to the following formula:
TD
A
= TD
0
+ T
INC
* A
PIN DESCRIPTIONS
IN
OUT
A2
A1
A0
ENB
VEE
GND
Signal Input
Signal Output
Address Bit 2
Address Bit 1
Address Bit 0
Output Enable
-5 Volts
Ground
where A is the address code, T
INC
is the incremental delay of the device,
and TD
0
is the inherent delay of the device. The incremental delay is
specified by the dash number of the device and can range from 0.5ns
through 50ns, inclusively. The enable pin (ENB) is held LOW during
normal operation. When this signal is brought HIGH, OUT is forced into a LOW state. The address is not
latched and must remain asserted during normal operation.
SERIES SPECIFICATIONS
•
•
•
•
•
•
•
•
Total programmed delay tolerance:
5% or 1ns,
whichever is greater
Inherent delay (TD
0
):
2.8ns typical
Setup time and propagation delay:
Address to input setup (T
AIS
):
3.6ns
Disable to output delay (T
DISO
):
1.7ns typical
Operating temperature:
0° to 70° C
Temperature coefficient:
100PPM/°C (excludes TD
0
)
Supply voltage V
EE
:
-5VDC
±
5%
Power Dissipation:
290mw typical (no load)
Minimum pulse width:
25% of total delay
DASH NUMBER SPECIFICATIONS
Part
Number
PDU108H-.5
PDU108H-1
PDU108H-2
PDU108H-3
PDU108H-5
PDU108H-10
PDU108H-20
PDU108H-40
PDU108H-50
Incremental Delay
Per Step (ns)
0.5
±
0.3
1.0
±
0.4
2.0
±
0.4
3.0
±
0.5
5.0
±
0.6
10.0
±
1.0
20.0
±
1.5
40.0
±
2.0
50.0
±
2.5
Total
Delay (ns)
3.5
±
1.0
7.0
±
1.0
14
±
1.0
21
±
1.0
35
±
1.7
70
±
3.5
140
±
7.0
280
±
14.0
350
±
17.5
NOTE: Any dash number between .5 and 50
not shown is also available.
©
2001 Data Delay Devices
Doc #97043
10/1/01
DATA DELAY DEVICES, INC.
3 Mt. Prospect Ave. Clifton, NJ 07013
1
PDU108H
APPLICATION NOTES
ADDRESS UPDATE
The PDU108H is a memory device. As such,
special precautions must be taken when
changing the delay address in order to prevent
spurious output signals. The timing restrictions
are shown in Figure 1.
After the last signal edge to be delayed has
appeared on the OUT pin, a minimum time, T
OAX
,
is required before the address lines can change.
This time is given by the following relation:
T
OAX
= max { (A
i
- A
i-1
) * T
INC
, 0 }
where A
i-1
and A
i
are the old and new address
codes, respectively. Violation of this constraint
may, depending on the history of the input signal,
cause spurious signals to appear on the OUT pin.
The possibility of spurious signals persists until
the required T
OAX
has elapsed.
A similar situation occurs when using the ENB
signal to disable the output while IN is active. In
this case, the unit must be held in the disabled
state until the device is able to “clear” itself. This
is achieved by holding the ENB signal high and
the IN signal low for a time given by:
T
DISH
= A
i
* T
INC
Violation of this constraint may, depending on the
history of the input signal, cause spurious signals
to appear on the OUT pin. The possibility of
spurious signals persists until the required T
DISH
has elapsed.
INPUT RESTRICTIONS
There are three types of restrictions on input
pulse width and period listed in the
AC
Characteristics
table. The
recommended
conditions are those for which the delay tolerance
specifications and monotonicity are guaranteed.
The
suggested
conditions are those for which
signals will propagate through the unit without
significant distortion. The
absolute
conditions
are those for which the unit will produce some
type of output for a given input.
When operating the unit between the
recommended and absolute conditions, the
delays may deviate from their values at low
frequency. However, these deviations will remain
constant from pulse to pulse if the input pulse
width and period remain fixed. In other words,
the delay of the unit exhibits frequency and pulse
width dependence when operated beyond the
recommended conditions. Please consult the
technical staff at Data Delay Devices if your
application has specific high-frequency
requirements.
Please note that the increment tolerances listed
represent a design goal. Although most delay
increments will fall within tolerance, they are not
guaranteed throughout the address range of the
unit. Monotonicity is, however, guaranteed over
all addresses.
A2-A0
T
AENS
ENB
T
ENIS
IN
TD
A
OUT
A
i-1
T
OAX
T
AIS
A
i
PW
IN
T
DISH
PW
OUT
T
DISO
Figure 1: Timing Diagram
Doc #97043
10/1/01
DATA DELAY DEVICES, INC.
Tel: 973-773-2299
Fax: 973-773-9672
http://www.datadelay.com
2
京公网安备 11010802033920号
EEWORLD
