EE-SPW311/411
Ratings and Specifications
Item
Sensing distance
Sensing object
Directional angle
Light source
Indicator
*1
Supply voltage
Current consumption
Models
1m
Opaque: 5 mm dia. min.
5 to 20°
GaAs infrared LED (pulse lighting) with a peak wavelength of 940 nm
Light indicator (red)
5 (−5%) to 24 (+10%) VDC, ripple (p-p): 5% max.
Emitter: 20 mA max., Receiver: 20 mA max.
NPN open collector:
Load power supply voltage: 5 to 24 VDC
Load current: 100 mA max.
OFF current: 0.5 mA max.
100 mA load current with a residual voltage of 0.8 V max.
10 mA load current with a residual voltage of 0.4 V max.
100 Hz min.
3,000 lx max. with incandescent light on the surface of the receiver
Operating:
−10
to +55°C
Storage:
−25
to +65°C
Operating: 5% to 85%
Storage: 5% to 95%
Destruction: 200 to 2,000 Hz (peak acceleration: 100 m/s
2
)
1.5-mm double amplitude for 2 h (4-min periods) each in X, Y, and Z
directions
Destruction: 500 m/s for 3 times each in X, Y, and Z directions
IEC IP60
Special connector (soldering not possible)
Approx. 8.8 g
Polybutylene phthalate (PBT)
Polycarbonate
EE-1006L/D Connectors with Cables, Instruction Manual
Optical axis
2
EE-SPW311, EE-SPW411
Control output
Response frequency
*2
Ambient illumination
Ambient temperature
range
Ambient humidity range
Vibration resistance
Shock resistance
Degree of protection
Connecting method
Weight (packaged)
Material
Accessories
Case
Lens
*1. The indicator is a GaP red LED
(peak wavelength: 700 nm).
*2. The response frequency was measured by
detecting the following rotating disk.
5 mm
5 mm
5 mm
1m
Engineering Data (Reference Value)
Receiver Output Excess Gain Vs.
Sensing Distance Characteristics
1,000
Receiver output excess gain (multiple)
500
300
100
50
30
10
5
3
1
20
Distance X
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
60
40
Distance Y
Parallel Movement Characteristics
Distance Y (mm)
140
120
100
80
Distance between sensors (m)
Distance X (m)
2
EE-SPW311/411
I/O Circuit Diagrams
NPN Output
Model
Output
configuration
Timing charts
Incident
Interrupted
Light indicator
(red)
Output
transistor
Load 1
(relay)
ON
OFF
Light indicator
(red)
Load
Main
circuit
OUT
5 to 24 VDC
Output circuit
EE-SPW411
Light-ON
ON
OFF
Operates
Releases
Incident
Interrupted
EE-SPW311
Dark-ON
Light indicator
(red)
Output
transistor
Load 1
(relay)
ON
OFF
ON
OFF
Operates
Releases
Safety Precautions
Refer to
Warranty and Limitations of Liability.
WARNING
This product is not designed or rated for ensuring
safety of persons either directly or indirectly.
Do not use it for such purposes.
●
Axis Adjustment
(1)Tentatively mount the emitter and receiver so that the center of
each lens is in a single line.
Side view
Precautions for Correct Use
Make sure that this product is used within the rated ambient
environment conditions.
●
Wiring
•
Connection is made using a connector. Do not solder to the pins
(leads).
•
When extending the cable, use an extension cable with conductors
having a total cross-section area of 0.3 mm
2
. The total cable length
must be less than 10 m.
Top view
(2)Turn ON the emitter and receiver after making sure that they have
been wired correctly. When power is turned ON, the light indicator
on the receiver will light. Make sure that the light indicator is OFF
when an object intercepts the optical axis and that the light
indicator lights again when the object is removed.
(3)Fix the position of the receiver (or emitter)
securely, move the emitter (or receiver)
horizontally and vertically to check the range in
which the operation indicator is lit. Then locate
the emitter (or receiver) in the center of the
range and fix the position securely.
3
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty.
Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy.
Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s
analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See
http://www.omron.com/global/
or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s
Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application.
Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
2013.12
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2013 All Right Reserved.
京公网安备 11010802033920号
EEWORLD
