Changes to Typical Connection Diagram section ................. 12
Change to Figure 18 ................................................................... 12
Changes to Reference Section................................................... 13
Changes to Timing Example 1.................................................. 14
8/03—Rev. 0: Initial Version
Rev. B | Page 2 of 20
AD7453
SPECIFICATIONS
V
DD
= 2.7 V to 5.25 V, f
SCLK
= 10 MHz, f
S
= 555 kSPS, V
REF
= 2.5 V, F
IN
= 100 kHz, T
A
= T
MIN
to T
MAX
, unless otherwise noted
Table 1.
Parameter
DYNAMIC PERFORMANCE
Signal to Noise Ratio (SNR)
2
Signal to (Noise + Distortion) (SINAD)
2
Total Harmonic Distortion (THD)
2
Peak Harmonic or Spurious Noise
2
Intermodulation Distortion (IMD)
2
Second-Order Terms
Third-Order Terms
Aperture Delay
2
Aperture Jitter
2
Full-Power Bandwidth
2, 3
DC ACCURACY
Resolution
Integral Nonlinearity (INL)
2
Differential Nonlinearity (DNL)
2
Offset Error
2
Gain Error
2
ANALOG INPUT
Full-Scale Input Span
Absolute Input Voltage
V
IN+
V
IN–4
DC Leakage Current
Input Capacitance
REFERENCE INPUT
V
REF
Input Voltage
DC Leakage Current
V
REF
Input Capacitance
LOGIC INPUTS
Input High Voltage, V
INH
Input Low Voltage, V
INL
Input Current, I
IN
Input Capacitance, C
IN 6
LOGIC OUTPUTS
Output High Voltage, V
OH
Output Low Voltage, V
OL
Floating-State Leakage Current
Floating-State Output Capacitance
6
Output Coding
Test Conditions/Comments
f
IN
= 100 kHz
V
DD
= 2.7 V to 5.25 V
V
DD
= 2.7 V to 3.6 V
V
DD
= 4.75 V to 5.25 V
V
DD
= 2.7 V to 3.6 V; –78 dB typ
V
DD
= 4.75 V to 5.25 V; –80 dB typ
V
DD
= 2.7 V to 3.6 V; –80 dB typ
V
DD
= 4.75 V to 5.25 V; –82 dB typ
fa = 90 kHz; fb = 110 kHz
A Version
1
70
69
70
–73
–75
–73
–75
–80
–80
5
50
20
2.5
12
±1.5
±0.95
±3.5
±3
V
REF
V
REF
–0.1 to +0.4
–0.1 to +1.5
±1
30/10
2.5
5
±1
10/30
2.4
0.8
±1
10
B Version
1
70
69
70
–73
–75
–73
–75
–80
–80
5
50
20
2.5
12
±1
±0.95
±3.5
±3
V
REF
V
REF
–0.1 to +0.4
–0.1 to +1.5
±1
30/10
2.5
5
±1
10/30
2.4
0.8
±1
10
Unit
dB min
dB min
dB min
dB max
dB max
dB max
dB max
dB typ
dB typ
ns typ
ps typ
MHz typ
MHz typ
Bits
LSB max
LSB max
LSB max
LSB max
V
V
V
V
µA max
pF typ
V
µA max
pF typ
V min
V max
µA max
pF max
V min
V min
V max
µA max
pF max
@ –3 dB
@ –0.1 dB
Guaranteed no missed codes to 12 bits
V
IN+
– V
IN–
V
DD
= 2.7 V to 3.6 V
V
DD
= 4.75 V to 5.25 V
When in track/hold
± 1% tolerance for specified performance
When in track/hold
Typically 10 nA, V
IN
= 0 V or V
DD
V
DD
= 4.75 V to 5.25 V, I
SOURCE
= 200 µA
V
DD
= 2.7 V to 3.6 V, I
SOURCE
= 200 µA
I
SINK
= 200 µA
2.8
2.8
2.4
2.4
0.4
0.4
±1
±1
10
10
Straight (natural) binary
Rev. B | Page 3 of 20
AD7453
Parameter
CONVERSION RATE
Conversion Time
Track-and-Hold Acquisition Time
2
Throughput Rate
POWER REQUIREMENTS
V
DD
I
DD7, 8
Normal Mode (Static)
Normal Mode (Operational)
Full Power-Down Mode
Power Dissipation
Normal Mode (Operational)
Full Power-Down Mode
Test Conditions/Comments
1.6 µs with a 10 MHz SCLK
Sine wave input
Full-scale step input
A Version
1
16
250
290
555
2.7/5.25
SCLK on or off
V
DD
= 4.75 V to 5.25 V
V
DD
= 2.7 V to 3.6 V
SCLK on or off
V
DD
= 5 V; 1.55 mW typ for 100 kSPS
7
V
DD
= 3 V; 0.64 mW typ for 100 kSPS
7
V
DD
= 5 V; SCLK on or off
V
DD
= 3 V; SCLK on or off
0.5
1.5
1.2
1
7.25
3.3
5
3
B Version
1
16
250
290
555
2.7/5.25
0.5
1.5
1.2
1
7.25
3.3
5
3
Unit
SCLK cycles
ns max
ns max
kSPS max
V min/max
mA typ
mA max
mA max
µA max
mW max
mW max
µW max
µW max
1
2
Temperature ranges as follows: A, B versions: –40°C to +85°C.
See Terminology section.
3
Analog inputs with slew rates exceeding 27 V/µs (full-scale input sine wave > 3.5 MHz) within the acquisition time may cause an incorrect result to be returned by the
converter.
4
A small dc input is applied to V
IN–
to provide a pseudo ground for V
IN+
.
5
The AD7453 is functional with a reference input in the range 100 mV to V
DD
.
6
Guaranteed by characterization.
7
See Power vs. Throughput Rate section.
8
Measured with a full-scale dc input.
Rev. B | Page 4 of 20
AD7453
TIMING SPECIFICATIONS
Guaranteed by characterization. All input signals are specified with tr = tf = 5 ns (10% to 90% of V
DD
) and timed from a voltage
level of 1.6 V.
See Figure 2 and the Serial Interface section.
V
DD
= 2.7 V to 5.25 V, f
SCLK
= 10 MHz, f
S
= 555 kSPS, V
REF
= 2.5 V, T
A
= T
MIN
to T
MAX
, unless otherwise noted.
Table 2.
Parameter
f
SCLK1
t
CONVERT
t
QUIET
t
1
t
2
t
32
t
42
t
5
t
6
t
7
t
83
t
POWER-UP 4
Limit at T
MIN
, T
MAX
10
10
16 × t
SCLK
1.6
60
10
10
20
40
0.4 t
SCLK
0.4 t
SCLK
10
10
35
1
Unit
kHz min
MHz max
µs max
ns min
ns min
ns min
ns max
ns max
ns min
ns min
ns min
ns min
ns max
µs max
Description
t
SCLK
= 1/f
SCLK
Minimum quiet time between the end of a serial read and the next falling edge of CS
Minimum CS pulse width
CS falling edge to SCLK falling edge setup time
Delay from CS falling edge until SDATA three-state disabled
Data access time after SCLK falling edge
SCLK high pulse width
SCLK low pulse width
SCLK edge to data valid hold time
SCLK falling edge to SDATA three-state enabled
SCLK falling edge to SDATA three-state enabled
Power-up time from full power-down
t
1
CS
t
2
SCLK
1
2
3
4
t
5
5
t
CONVERT
B
13
14
15
16
SDATA
0
0
0
4 LEADING ZEROS
0
DB11
DB10
DB2
DB1
DB0
t
QUIET
THREE-STATE
Figure 2. AD7453 Serial Interface Timing Diagram
1
2
Mark/space ratio for the SCLK input is 40/60 to 60/40.
Measured with the load circuit of Figure 3 and defined as the time required for the output to cross 0.8 V or 2.4 V with V
DD
= 5 V, and the time required for an output to
cross 0.4 V or 2.0 V for V
DD
= 3 V.
3
t
8
is derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 3. The measured number is then extrapolated
back to remove the effects of charging or discharging the 25 pF capacitor. This means that the time, t
8
, quoted in the timing characteristics is the true bus relinquish
time of the part and is independent of the bus loading.
京公网安备 11010802033920号
EEWORLD
