Mounted on a FR4 glass epoxy PCB 70mm×70mm×1.6mm (Copper foil area less than 3%).
The voltage difference between inverting input and non-inverting input is the differential input voltage.
Then input terminal voltage is set to more than VSS.
(Note 8) An excessive input current will flow when input voltages of more than VDD+0.6V or less than VSS-0.6V are applied.
The input current can be set to less than the rated current by adding a limiting resistor.
Caution: Operating the IC over the absolute maximum ratings may damage the IC. In addition, it is impossible to predict all destructive situations such as
short-circuit modes, open circuit modes, etc. Therefore, it is important to consider circuit protection measures, like adding a fuse, in case the IC is
operated in a special mode exceeding the absolute maximum ratings.
Parameter
Supply Voltage
Symbol
VDD-VSS
SSOP5
SOP8
Rating
BU7461SG
0.54
(Note9,14)
BU7462Sxxx
+7
-
0.55
0.47
0.41
(Note10,14)
(Note11,14)
(Note12,14)
BU7464SF
-
-
-
-
0.45
(Note13,14)
Unit
V
-
-
-
-
Power Dissipation
P
D
MSOP8
VSON008X2030
SOP14
W
-
VDD - VSS
Differential Input Voltage
Input Common-mode
Voltage Range
Input Current
(Note 16)
(Note 15)
V
ID
V
ICM
I
I
V
opr
T
opr
T
stg
T
Jmax
V
V
mA
V
°C
°C
°C
(VSS-0.3) to (VDD+0.3)
±10
+1.7V to +5.5V
-40 to +105
-55 to +125
+125
Operating Supply Voltage
Operating Temperature
Storage Temperature
Maximum Junction Temperature
(Note 9)
(Note 10)
(Note 11)
(Note 12)
(Note 13)
(Note 14)
(Note 15)
To use at temperature above T
A
=25C reduce 5.4mW/C.
To use at temperature above T
A
=25C reduce 5.5mW/C.
To use at temperature above T
A
=25C reduce 4.7mW/C.
To use at temperature above T
A
=25C reduce 4.1mW/C.
To use at temperature above T
A
=25C reduce 4.5mW/C.
Mounted on a FR4 glass epoxy PCB 70mm×70mm×1.6mm (Copper foil area less than 3%).
The voltage difference between inverting input and non-inverting input is the differential input voltage.
Then input terminal voltage is set to more than VSS.
(Note 16) An excessive input current will flow when input voltages of more than VDD+0.6V or less than VSS-0.6V are applied.
The input current can be set to less than the rated current by adding a limiting resistor.
Caution: Operating the IC over the absolute maximum ratings may damage the IC. In addition, it is impossible to predict all destructive situations such as
short-circuit modes, open circuit modes, etc. Therefore, it is important to consider circuit protection measures, like adding a fuse, in case the IC is
operated in a special mode exceeding the absolute maximum ratings.
Hello everyone! We are going to develop a SIM card reader. The GSM protocol mentions the concept of dialling number, but does not clearly state how the address book is stored. What is the relationship...
I use F28027 to operate NOKIA5110 LCD. Since there is no font library in the night scene, it needs to be created manually. Now there are several problems: (1) If the font library is created in FLASH, ...
[b]Factors Affecting PCB Welding Quality[/b][align=left][color=rgb(51, 51, 51)][font=-apple-system-font, BlinkMacSystemFont, "][size=17px]From PCB design to the completion of all component welding to ...
Where is the starting address of 1 RAM mapped to in 2410? How big is the capacity? 2 Where is the starting address of ROM mapped to? How big is the capacity? 2410 startup method: 3 When 2410 is extern...
High efficiency and low standby power consumption are two major challenges in today's switching power supply design. Resonant topology or LLC topology is becoming increasingly popular because it ca...[Details]
The rapid development of the Internet has realized high-speed information transmission and resource sharing, greatly facilitating people's lives. Embedded systems are widely used in various electr...[Details]
Hardware designers have begun to adopt FPGA technology in high-performance DSP designs because it can provide 10-100 times faster computing than PC-based or microcontroller-based solutions. Previou...[Details]
Do you often have to add brake fluid to your car's brakes? The fact that you need to pump out the brake fluid to make sure there is no gas in the brake fluid line may not be done by the car owner h...[Details]
introduction
Solar cells and LED lighting are typical applications of new energy and energy-saving and efficient technologies. Solar LED lighting uses solar cells to convert solar energy...[Details]
For a long time, due to the limitation of hardware conditions, the display devices of traditional small handheld devices such as PDA are usually monochrome LCD, and the user interface is very simpl...[Details]
Images in science fiction movies often break through the limits of reality, such as in the movie "Minority Report." Tom Cruise uses a multi-touch screen to browse information. Capacitive sensing te...[Details]
With the development and widespread application of computer technology, especially in the field of industrial control, computer communication is particularly important. Although serial communication g...[Details]
Xiaomi, a well-known Internet phone in mainland China, won a million-unit order contract from China Unicom on November 20 last year, which made Xiaomi famous in mainland China. In April this year...[Details]
At very low temperatures, certain metals and alloys lose their resistance to electric
current
and become
superconductors
. Two parameters that are often measured are the transition ...[Details]
introduction
MEMS is a high-tech that has flourished on the basis of integrated circuit production technology and dedicated micro-electromechanical processing methods. Pressure sensors develop...[Details]
Abstract: With the development and construction of BeiDou II system, China will shift from the situation dominated by GPS to the situation dominated by BeiDou II global navigation system independen...[Details]
LED guardrail lights use fluorescent tubes or LEDs as light sources and continuous guardrails as carriers to form an approximately linear guardrail light strip. This article mainly introduces...[Details]
Currently, each country is developing its own USB interface
charging specifications
, which leads to a major problem that a USB interface
charging
device manufactured in one country...[Details]
Abstract: In order to realize wireless automatic alarm and monitoring of major safety places, based on the basic principle of pyroelectric infrared sensing, a detector for receiving infrared radia...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
