Freescale Semiconductor
MPC5604BCRM
Rev. 8.2, 09/2013
MPC5604B/C Microcontroller
Reference Manual
This is the MPC5604B/C Reference Manual set consisting of the following files:
•
MPC5604B/C Reference Manual Addendum (MPC5604B/CRMAD),
Rev. 2
•
MPC5604B/C Reference Manual (MPC5604B/CRM),
Rev. 8
© Freescale Semiconductor, Inc., 2013. All rights reserved.
Freescale Semiconductor
Reference Manual Addendum
MPC5604BRMAD
Rev. 2, 09/2013
MPC5604B/C Microcontroller
Reference Manual Addendum
This addendum describes corrections to the
MPC5604B/C Microcontroller Reference Manual,
order
number MPC5604BCRM. For convenience, the addenda
items are grouped by revision. Please check our website
at http://www.freescale.com/powerarchitecture for the
latest updates.
The current version available of the
MPC5604B/C
Microcontroller Reference Manual
is Revision 8.1.
Table of Contents
1
2
3
Addendum List for Revision 8.1 . . . . . . . . . . . . . . 2
Addendum List for Revision 8 . . . . . . . . . . . . . . . . 2
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . 4
© Freescale Semiconductor, Inc., 2013. All rights reserved.
1
Addendum List for Revision 8.1
Table 1. MPC5604BCRM Rev 8.1 Addenda
Location
Description
Add a note below Table 27-4, “CFlash TestFlash Structure”.
NOTE
Unique Device ID – Memory location. This device now includes a 128-bit Unique
Identification number (UID) which is programmed during device fabrication.
Start – Stop Address Size (Bytes) Content:
•
0x00403C10 0x00403C17 8 UID 1
•
0x00403C18 0x00403C1F 8 UID 2
Chapter 27, “Flash Memory”
page 644
2
Addendum List for Revision 8
Table 2. MPC5604BCRM Rev 8 Addenda
Location
Description
Chapter 4, Signal description, In Table 4-3, Functional port pin descriptions, row PH[9], change the pin numbers for
page 60
MPC560xB 64 LQFP and MPC560xC 64 LQFP from “—” to 60.
In row PH[10], change the pin numbers for MPC560xB 64 LQFP and MPC560xC 64 LQFP
from “—” to 53.
Chapter 6, Clock Description, Add
Note:
to Section 6.8.4.1, Crystal clock monitor:
page 113
Note:
Functional FXOSC monitoring can only be guaranteed when the FXOSC frequency is
greater than (FIRC / 2
RCDIV
) + 0.5 MHz.
Add
Note:
to Section 6.8.4.2, FMPLL clock monitor:
Note:
Functional FMPLL monitoring can only be guaranteed when the FMPLL frequency is
greater than (FIRC / 4) + 0.5 MHz.
Chapter 9, Reset Generation Replace Section 9.4.7, Boot Mode Capturing, with the following:
Module (MC_RGM), page
209
The MC_RGM samples PA[9:8] whenever RESET is asserted until five FIRC (16 MHz internal
RC oscillator) clock cycles before its deassertion edge. The result of the sampling is used at
the beginning of reset PHASE3 for boot mode selection and is retained after RESET has been
deasserted for subsequent boots after reset sequences during which RESET is not asserted.
Note:
In order to ensure that the boot mode is correctly captured, the application needs to
apply the valid boot mode value the entire time that RESET is asserted.
RESET can be asserted as a consequence of the internal reset generation. This will force
re-sampling of the boot mode pins. (See Table 9-12 for details.)
Chapter 13, Real Time Clock / In Table 13-3 (RTCC field descriptions), update Note in RTCC[APIVAL] field description:
Autonomous Periodic
Interrupt (RTC/API), page
Note:
API functionality starts only when APIVAL is nonzero. The first API interrupt takes two
262
more cycles because of synchronization of APIVAL to the RTC clock, and APIVAL + 1 cycles
for subsequent occurrences. After that, interrupts are periodic in nature. Because of
synchronization issues, the minimum supported value of APIVAL is 4.
MPC5604BRMAD, Rev. 2
2
Freescale Semiconductor
Table 2. MPC5604BCRM Rev 8 Addenda
Location
Chapter 21, LINFlex, p. 412
Insert the following section:
Description
21.8.2.1.6
Overrun
Once the message buffer is full, the next valid message reception leads to an
overrun and a message is lost. The hardware sets the BOF bit in the LINSR to
signal the overrun condition. Which message is lost depends on the
configuration of the RX message buffer:
• If the buffer lock function is disabled (LINCR1[RBLM] = 0) the last
message stored in the buffer is overwritten by the new incoming
message. In this case the latest message is always available to the
application.
• If the buffer lock function is enabled (LINCR1[RBLM] = 0) the most
recent message is discarded and the previous message is available in the
buffer.
Chapter 22, FlexCAN,
throughout chapter
Chapter 22, FlexCAN, page
429
Chapter 22, FlexCAN, page
461
Remove references throughout the chapter to “low-cost MCUs.”
Add this Note in the RTR field description of Table 22-4 (Message Buffer Structure field
description):
Note:
Do not configure the last Message Buffer to be the RTR frame.
In Section 22.4.9.4, Protocol timing, update the Note following Figure 22-16 (CAN engine
clocking scheme) to read: “This clock selection feature may not be available in all MCUs. A
particular MCU may not have a PLL, in which case it would have only the oscillator clock, or
it may use only the PLL clock feeding the FlexCAN module. In these cases, the CLK_SRC bit
in the CTRL Register has no effect on the module operation.”
Update the table title of Table 22-20 from “CAN Standard Compliant Bit Time Segment Settings”
to “Bosch CAN 2.0B standard compliant bit time segment settings.”
In Section 22.4.9.4, Protocol timing, update the Note following Table 22-20 to read: “Other
combinations of Time Segment 1 and Time Segment 2 can be valid. It is the user’s
responsibility to ensure the bit time settings are in compliance with the CAN standard. For bit
time calculations, use an IPT (Information Processing Time) of 2, which is the value
implemented in the FlexCAN module.”
Chapter 22, FlexCAN, page
462
Chapter 22, FlexCAN, page
463
Chapter 25, Analog-to-Digital In Section 28.3.5.2, Presampling channel enable signals, in Table 28-7, Presampling voltage
Converter (ADC), page
selection based on PREVALx fields, in the 01 row, change the “Presampling voltage” field to:
V1 = V
DD_HV_ADC0
or V
DD_HV_ADC1
.
Chapter 25, Analog-to-Digital In Section 25.3.2, Analog clock generator and conversion timings, remove the paragraph:
Converter (ADC), page 597
The direct clock should basically be used only in low power mode when the device is using
only the 16 MHz fast internal RC oscillator, but the conversion still requires a 16 MHz clock
(an 8 MHz clock is not fast enough). In all other cases, the ADC should use the clock divided
by two internally.
MPC5604BRMAD, Rev. 2
Freescale Semiconductor
3
Table 2. MPC5604BCRM Rev 8 Addenda
Location
Description
Chapter 25, Analog-to-Digital In Section 25.3.4.2, CTU in trigger mode, replace the sentence:
Converter (ADC), p. 600
If another CTU conversion is triggered before the end of the conversion, that request is
discarded.
with:
If another CTU conversion is triggered before the end of the conversion, that request is
discarded. However, if the CTU has triggered a conversion that is still ongoing on a channel,
it will buffer a second request for the channel and wait for the end of the first conversion before
requesting another conversion. Thus, two conversion requests close together will both be
serviced.
Chapter 25, Analog-to-Digital Add Note to Section 25.3.10, Auto-clock-off mode:
Converter (ADC), page 603
Note:
The auto-clock-off feature cannot operate when the digital interface runs at the same
rate as the analog interface. This means that when MCR.ADCCLKSEL = 1, the analog clock
will not shut down in IDLE mode.
Chapter 25, Analog-to-Digital In Section 25.4.6.2, Main Status Register (MSR), replace the ADCSTATUS field description with
Converter (ADC), page 610
the following:
The value of this parameter depends on ADC status:
000 IDLE — The ADC is powered up but idle.
001 Power-down — The ADC is powered down.
010 Wait state — The ADC is waiting for an external multiplexer. This occurs only when the
DSDR register is nonzero.
011 Reserved
100 Sample — The ADC is sampling the analog signal.
101 Reserved
110 Conversion — The ADC is converting the sampled signal.
111 Reserved
Chapter 26, Cross Triggering At the end of Section 26.4.1, Event Configuration Registers (CTU_EVTCFGRx) (x = 0...63), add
Unit (CTU), page 633
the following Note:
NOTE
The CTU tracks issued conversion requests to the ADC. When the ADC
is being triggered by the CTU and there is a need to shut down the ADC,
the ADC must be allowed to complete conversions before being shut
down. This ensures that the CTU is notified of completion; if the ADC
is shut down while performing a CTU-triggered conversion, the CTU is
not notified and will not be able to trigger further conversions until the
device is reset.
3
Revision History
Table 3. Revision History Table
Rev. Number
2.0
1.0
Substantive Changes
Add a note below Table 27-4, “CFlash TestFlash Structure”
Initial release.
Date of Release
09/2013
05/2012
Table 3
provides a revision history for this reference manual addendum document.
MPC5604BRMAD, Rev. 2
4
Freescale Semiconductor
京公网安备 11010802033920号
EEWORLD
