DS1052 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > DS1052

Preview

DS1052: Description5-Bit, Programmable, 100kHz Pulse-Width Modulator; File Size200KB，14 Pages; ManufacturerDALLAS; Websitehttp://www.dalsemi.com

Download Datasheet Compare View All

DS1052 Overview

5-Bit, Programmable, 100kHz Pulse-Width Modulator

Preview

Download Datasheet

View All

DS1052

5-Bit, Programmable, 100kHz

Pulse-Width Modulator

www.maxim-ic.com

FEATURES

Single 5-bit, programmable, pulse-width

modulator (PWM)

Adjustable Duty Cycle: 0% to 100%

2.7V to 5.5V Operation

Standard Frequency Value: 100kHz

2-Wire Addressable Interface

Packages: 8-Pin (150-mil) SOIC and 8-Pin

(118-mil)

mSOP

Operating Temperature: -40

C to +85

PIN ASSIGNMENT

SCL

SDA

GND

PWM

ORDERING INFORMATION

DS1052Z-100

DS1052U-100

100kHz

8-Pin 150-mil SOIC

8-Pin 118-mil

mSOP

8-Pin 150-mil SOIC

8-Pin 118-mil

mSOP

PIN DESCRIPTION

PWM

A0, A1, A2

SDA

SCL

GND

- 2.7V to 5.5V Power Supply

- PWM Ouput

- Device Address

- Serial Data I/O

- Serial Clock Input

- Ground

DESCRIPTION

The DS1052 is a programmable, 5-bit, pulse-width modulator featuring a 2-wire addressable controlled

interface. The DS1052 operates from power supplies ranging from 2.7V up to 5.5V. The PWM output

provides a signal that swings from 0V to V

The DS1052-100 requires a typical operating current of 100µA and a programmable shutdown supply

current of 1µA.

One standard PWM output frequency is offered: 100kHz. The 2-wire addressable interface allows

operation of multiple devices on a single 2-wire bus and provides compatibility with other Dallas

Semiconductor 2-wire devices such as real-time clocks (RTCs), digital thermometers, and digital

potentiometers.

The device is ideal for low-cost LCD contrast and/or brightness control, power supply voltage

adjustment, and battery charging or current adjustment. The DS1052 is offered in standard integrated

circuit packaging, including the 8-pin (150-mil) SOIC and space-saving 8-pin (118-mil)

mSOP.

1 of 14

072601

DS1052

OPERATION

Interface protocol is simplified to an 8-bit control byte and 8-bit data byte. Information can be read or

written to the DS1052 including a commanded shutdown operation.

Power-Up Configuration

The DS1052 powers-up to half-scale (10000B) providing 50% duty-cycle. In this mode, the DS1052 can

be used as a standalone oscillator of the frequency specified. Once powered, the PWM output can be

changed via the 2-wire addressable serial port.

Pin Description

– Power supply terminal. The DS1052 will support operation from power supply voltages ranging

from +2.7 volts to +5.5 volts.

GND

– Ground terminal.

PWM

– Pulse-width modulated output. This output is a square-wave having amplitudes from 0 volts to

. The duty cycle of this output is governed by a 5-bit control register. Output duty cycles range from

0% to 96.88%. An additional command sequence will provide a 100% duty cycle or “full-on.”

SCL

– Serial clock input.

SDA

– Serial bi-directional data I/O.

A0, A1, A2

– Device address (chip selects).

2-Wire Addressable Serial Port Control

The 2-wire serial port interface supports a bi-directional data transmission protocol with device

addressing. A device that sends data on the bus is defined as a transmitter, and a device receiving data as

a receiver. The device that controls the message is called a “master.” The devices that are controlled by

the master are “slaves.” The bus must be controlled by a master device that generates the serial clock

(SCL), controls the bus access, and generates the START and STOP conditions. The DS1052 operates as

a slave on the 2-wire bus. Connections to the bus are made via the open-drain I/O lines SDA and SCL.

The following I/O terminals control the 2-wire serial port: SDA, SCL, A0, A1, and A2. A 2-wire serial

port overview and timing diagrams for the 2-wire serial port can be found in Figures 2 and 5,

respectively. Timing information for the 2-wire serial port is provided in the “AC Electrical

Characteristics” table for 2-wire serial communications.

2 of 14

DS1052

The following bus protocol has been defined (See Figure 2):

Data transfer may be initiated only when the bus is not busy.

During data transfer, the data line must remain stable whenever the clock line is HIGH. Changes in

the data line while the clock line is high will be interpreted as control signals.

Accordingly, the following bus conditions have been defined:

Bus not busy:

Both data and clock lines remain HIGH.

Start data transfer:

A change in the state of the data line from HIGH to LOW while the clock is HIGH,

defines a START condition.

Stop data transfer:

A change in the state of the data line from LOW to HIGH while the clock line is

HIGH defines the STOP condition.

Data valid:

The state of the data line represents valid data when, after a START condition, the data line

is stable for the duration of the HIGH period of the clock signal. The data on the line must be changed

during the LOW period of the clock signal. There is one clock pulse per bit of data. Figure 2 details how

data transfer is accomplished on the 2-wire bus. Depending upon the state of the R/W bit, two types of

data transfer are possible.

Each data transfer is initiated with a START condition and terminated with a STOP condition. The

number of data bytes transferred between START and STOP conditions is not limited and is determined

by the master device. The information is transferred byte-wise and each receiver acknowledges with a

ninth bit.

Within the bus specifications, a regular mode (100kHz clock rate) and a fast mode (400kHz clock rate)

are defined. The DS1052 works in both modes.

Acknowledge:

Each receiving device, when addressed, is obliged to generate an acknowledge after the

reception of each byte. The master device must generate an extra clock pulse that is associated with this

acknowledge bit.

A device that acknowledges must pull down the SDA line during the acknowledge clock pulse in such a

way that the SDA line is stable LOW during the HIGH period of the acknowledge-related clock pulse. Of

course, setup and hold times must be taken into account. A master must signal an end of data to the slave

by not generating an acknowledge bit on the last byte that has been clocked out of the slave. In this case,

the slave must leave the data line HIGH to enable the master to generate the STOP condition.

Data transfer from a master transmitter to a slave receiver.

The first byte transmitted by the

master is the command/control byte. Next follows a number of data bytes. The slave returns an

“acknowledge” bit after each received byte.

Data transfer from a slave transmitter to a master receiver.

The first byte (the command/control

byte) is transmitted by the master. The slave then returns an acknowledge bit. Next follows a number

of data bytes transmitted by the slave to the master. The master returns an acknowledge bit after all

received bytes other than the last byte. At the end of the last received byte, a “not acknowledge” is

returned.

3 of 14

DS1052

The master device generates all serial clock pulses and the START and STOP conditions. A transfer is

ended with a STOP condition or with a repeated START condition. Since a repeated START condition is

also the beginning of the next serial transfer, the bus will not be released.

The DS1052 may operate in the following two modes:

Slave receiver mode:

Serial data and clock are received through SDA and SCL, respectively. After

each byte is received, an acknowledge bit is transmitted. START and STOP conditions are recognized

as the beginning and end of a serial transfer. Address recognition is performed by hardware after

reception of the slave (device) address and direction bit.

Slave transmitter mode:

The first byte is received and handled as in the slave receiver mode.

However, in this mode the direction bit will indicate that the transfer direction is reversed. Serial data

is transmitted on SDA by the DS1052 while the serial clock is input on SCL. START and STOP

conditions are recognized as the beginning and end of a serial transfer.

SLAVE ADDRESS

A command/control byte is the first byte received following the START condition from the master

device. The command/control byte consists of a four-bit control code. For the DS1052, this is set as

0101

binary for read/write operations. The next three bits of the command/control byte are the device select

bits or slave address (A2, A1, A0). They are used by the master device to select which of eight possible

devices is to be accessed. When reading or writing the DS1052, the device select bits must match the

device select pins (A2, A1, A0). The last bit of the command/control byte (R/W) defines the operation to

be performed. When set to a one a read operation is selected, and when set to a zero a write operation is

selected. The command control byte is presented in Figure 3.

Following the START condition, the DS1052 monitors the SDA bus checking the device type identifier

being transmitted. Upon receiving the 0101 control code, the appropriate device address bits, and the

read/write bit, the slave device outputs an “acknowledge” signal on the SDA line.

COMMAND AND PROTOCOL

The command and protocol structure of the DS1052 allows the user to read or write the PWM

configuration register or place the device in a low-current state (shut-down mode) and recall the device

from a low-current state. Additionally, the 2-wire command/protocol structure of the DS1052 will support

eight different devices that can be uniquely controlled.

Figure 4a, b, c, d, & e show the five different command and protocol bytes for the DS1052. These include

the following command operations: 1) Set PWM duty cycle, 2) Set PWM duty cycle 100%, 3) Set

shutdown mode, 4) Set recall mode, 5) Read PWM configuration register.

The command operation “Set PWM Duty Cycle” is used to configure the output duty cycle of the device.

The DS1052 has a 5-bit resolution and is capable of setting the duty cycle output from 0% up to 96.88%

in steps of 3.125%. A binary value of (00000B) sets the duty cycle output at 0% while a binary value of

(11111B) sets the duty cycle output at 96.88%.

The command operation “Set PWM Duty Cycle 100%” is used to configure the output duty cycle of the

device to a “full-on.” This command is provided in addition to the Set PWM Duty Cycle command for

flexibility and convenience in total duty cycle coverage. It allows the user to provide a total duty cycle

range from 0% to 100%.

4 of 14

DS1052

The command operation “Set Shutdown Mode” is used to provide a low-current (inactive state) state for

the DS1052. When in a low-current state the DS1052 will draw currents less than or equal to 1mA. The

PWM

output will be high impedance.

The command operation “Set Recall Mode” is used to recall the DS1052 from a low-current state. The

value of the PWM

output is recalled to that prior to initiating a “Set shutdown mode” command.

The “Read PWM Duty Cycle” command is used to read the current setting of the PWM configuration

is in a shutdown configuration.

PWM data values and control/command values are always transmitted most significant bit (MSB) first.

During communications, the receiving unit always generates the “acknowledge.”

READING THE DS1052

As shown in Figure 4e, the DS1052 provides one

read command operation.

This operation allows the

user to read the current setting of the PWM configuration register. Specifically, the R/W bit of the

command/control byte is set equal to a 1 for a read operation. Communication to read the DS1052 begins

with a START condition which is issued by the master device. The command/control byte from the

master device will follow the START condition. Once the command/control byte has been received by

the DS1052, the part will respond with an ACKNOWLEDGE. The read/write bit of the command/control

byte, as stated, should be set equal to 1 for reading the DS1052.

When the master has received the ACKNOWLEDGE from the DS1052, the master can then begin to

receive the PWM configuration register data. As mentioned this data will be transmitted MSB first. Once

the eight bits of the PWM configuration register have been transmitted, the master will need to issue an

ACKNOWLEDGE, unless it is the only byte to be read, in which case the master issues a NOT

ACKNOWLEDGE. If desired the master may stop the communication transfer at this point by issuing the

STOP condition. Final communication transfer is terminated by issuing the STOP command. Again, the

flow of the read operation is presented in Figure 4e.

WRITING THE DS1052

A data flow diagram for writing the DS1052 is shown in Figures 4a, b, c, and d. The DS1052 has three

write commands that are used to change the PWM configuration register or the shutdown and recall mode

of the device.

All the write operations begin with a START condition. Following the START condition, the master

device will issue the command/control byte. The read/write bit of the command/control byte will be set to

“0” for writing the DS1052. Once the command/control byte has been issued and the master receives the

acknowledgment from the DS1052, PWM configuration data is transmitted to the DS1052 by the master

device.

A data byte for the DS1052 will contain PWM configuration data and shutdown/recall command data.

The five least significant bits of data specify the PWM configuration value while the three most

significant bits specify the whether the device is to be shutdown or recalled. When the DS1052 has

received the data byte, it will respond with an ACKNOWLEDGE. At this point, the new PWM

configuration register value and shutdown/recall command value will be updated in the DS1052. The

master device, after the receipt of the ACKNOWLEDGE, can continue to transmit additional data bytes

5 of 14

DS1052 Related Products

	DS1052	DS1052Z-100	DS1052U-100
Description	5-Bit, Programmable, 100kHz Pulse-Width Modulator	5-Bit, Programmable, 100kHz Pulse-Width Modulator	5-Bit, Programmable, 100kHz Pulse-Width Modulator
Is it Rohs certified?	-	incompatible	incompatible
Maker	-	DALLAS	DALLAS
package instruction	-	0.150 INCH, SOIC-8	0.118 INCH MICRO, SO-8
Reach Compliance Code	-	unknow	unknow
Analog Integrated Circuits - Other Types	-	ANALOG CIRCUIT	ANALOG CIRCUIT
JESD-30 code	-	R-PDSO-G8	R-PDSO-G8
JESD-609 code	-	e0	e0
Number of functions	-	1	1
Number of terminals	-	8	8
Maximum operating temperature	-	85 °C	85 °C
Minimum operating temperature	-	-40 °C	-40 °C
Package body material	-	PLASTIC/EPOXY	PLASTIC/EPOXY
encapsulated code	-	SOP	SOP
Encapsulate equivalent code	-	SOP8,.25	TSSOP8,.19
Package shape	-	RECTANGULAR	RECTANGULAR
Package form	-	SMALL OUTLINE	SMALL OUTLINE
power supply	-	2.5/5.5 V	2.5/5.5 V
Certification status	-	Not Qualified	Not Qualified
Maximum supply voltage (Vsup)	-	5.5 V	5.5 V
Minimum supply voltage (Vsup)	-	2.5 V	2.5 V
Nominal supply voltage (Vsup)	-	3 V	3 V
surface mount	-	YES	YES
technology	-	CMOS	CMOS
Temperature level	-	INDUSTRIAL	INDUSTRIAL
Terminal surface	-	Tin/Lead (Sn/Pb)	Tin/Lead (Sn/Pb)
Terminal form	-	GULL WING	GULL WING
Terminal pitch	-	1.27 mm	0.635 mm
Terminal location	-	DUAL	DUAL

Recommended Resources

Light controlled lantern circuit

Switching power supply thick film control circuit and application-actual circuit

Positive peak detector circuit diagram C

Transistor single tube time delay pull-in relay

Circuit functional block diagram

Infrared light controlled toy tank circuit

Please help me understand what this paragraph means: This is a section of assembly code in STM8 motor, but after reading it, I just can't understand what it means. The low-level code is as follows:;********************* PHASE U duty cycle processing ***...; JIAOYANGJITUAN stm32/stm8

Programming in Matlab to display the graphics of data files: How can I write a program in Matlab to display the data file in a graphic? I know that I can use the fopen, fread, and fseek functions, but how can I draw the data in the binary file into a graphic? T...; xiaopp891117 Microcontroller MCU

The basic principles and effective use of RF directional couplers: Electronic systems are increasingly using RF sources in radio frequency (RF) applications such as automotive radar, 5G cellular, and the Internet of Things. All of these RF sources require ways to mon...; Jacktang RF/Wirelessly

DIY the simplest mobile phone schematic: Please give us your comments and suggestions!...; lcofjp MCU

STM32 program download problem: I recently used ulink2 to download programs, but an error dialog box always popped up: "cannot enter debug mode". I don't know what went wrong. I have been troubled by this for half a month. Now I can...; ttlcoms stm32/stm8

Find the serial number of WinDriver8 or 9: As the title says. If it works, I will give you points immediately....; deeply Embedded System

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components