8-320565-5 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > The connector> 8-320565-5

8-320565-5: DescriptionCOPPER ALLOY, TIN FINISH, WIRE TERMINAL; CategoryThe connector; File Size731KB，14 Pages; ManufacturerTE Connectivity; Websitehttp://www.te.com

Download Datasheet Parametric View All

8-320565-5 Overview

COPPER ALLOY, TIN FINISH, WIRE TERMINAL

8-320565-5 Parametric

Parameter Name	Attribute value
Objectid	1508785242
Reach Compliance Code	unknown
ECCN code	EAR99
terminal gender	FEMALE
Terminal and terminal strip types	RING TERMINAL
Wire gauge	14 AWG

Preview

Download Datasheet

View All

Application Specification

Pre-Insulated Diamond Grip (PIDG*)

Terminals, Splices, and End Caps

114-2157

09 SEP 08

Rev E

NOTE

All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and

inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2 .

Figures and illustrations are for identification only and are not drawn to scale.

1. INTRODUCTION

This specification covers the requirements for application of PIDG terminals, splices, and end caps in various

operating environments. Each consists of a precision–formed metal wire barrel and a copper sleeve encased in

insulating material made of nylon, polyvinyl chloride (PVC) or polyvinyl fluoride (PVF

). The insulation is color

coded (solid primary color or a primary color with a color stripe) to correspond with a specific wire size or wire

size range. The terminals, splices, and end caps accept a combination of solid and stranded wire. The wire

barrel contains serrations that provide maximum contact and tensile strength after crimping the terminal, splice,

or end cap onto the wire. The terminals are available with a variety of tongue lengths and configurations; and

the terminals, splices, and end caps are available with various wire barrel lengths and diameters to

accommodate different wire sizes, wire types, and combination of wire sizes.

The terminals, splices, and end caps are available in loose piece form to be terminated with manual and

pneumatically–powered hand held tools and tape mounted to be terminated with bench mount semi–automatic

machines.

When corresponding with personnel, use the terminology provided in this specification to facilitate your

inquiries for information. Basic terms and features of this product are provided in Figure 1.

Terminal

In-Line Ring Tongue

Wire Barrel

Copper

Sleeve

Tongue

Multiple Stud Hole

Spring Spade Tongue

Insulation

Flanged Spade Tongue

Right Angle Ring Tongue

Offset Ring Tongue

Hook Tongue

In-Line Rectangular Tongue

Right-Angle Rectangular Tongue

Knife Connect/Disconnect

Figure 1 (Cont’d)

2008 Tyco Electronics Corporation, Harrisburg, PA

TOOLING ASSISTANCE CENTER 1-800-722-1111

PRODUCT INFORMATION 1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at

www.tycoelectronics.com

All International Rights Reserved

TE logo and Tyco Electronics are trademarks.

of 14

LOC B

*Trademark. Other products, logos, and company names used are the property of their respective owners.

PIDG Terminals, Splices, and End Caps

114-2157

NOTE

The wire conductor(s) must not be nicked, scraped, or cut during the stripping operation.

3.4. Wire Placement

The stripped wire must be inserted into the wire barrel until the wire insulation is against the wire barrel but not

inside it. The wire insulation must be inside the metal sleeve. A gap between the wire insulation and wire barrel

is allowed, but not to exceed the dimension given in Figure 3.

Transparent Insulation Window Butt Splice Shown

1.59 [.062]

Splice

Insulation

Maximum Gap

Wire Insulation May Butt Against,

Wire Barrel

But Not Enter, Wire Barrel

Metal Sleeve

Wire Insulation Must Be

Inside Metal Sleeve

Figure 3

3.5. Crimp Requirements

A. Crimp Height

The spring–back of the terminal, splice, or end cap insulation prevents an accurate direct measurement of

crimp height. However, crimping a slug of solder (60% tin and 40% lead) with a diameter slightly larger

than the conductor outside diameter can verify proper termination. The crimp height of the resulting solder

slug can be checked with a standard micrometer or comparator. The measurement must be made over

the most compressed area of the solder slug. See Figure 4.

NOTE

Some tooling with multiple crimping chambers form an embossed dot code in the terminal, splice, or end cap

insulation that indicates which crimping chamber was used. This dot code can be used as a visual inspection to ensure

that the correct wire size and crimping chamber were used.

The resilience of the splice insulation prevents accurate direct measurement of crimp height. Crimp height can be

obtained by measuring a crimped solder slug (60% tin and 40% lead) with a diameter comparable to the wire size.

The slug must be measured over the most compressed area of the slug with a standard micrometer or crimp height

comparator (refer to 408-7424 for specific instructions). The solder slug diameter and crimp height must be within the

dimensions provided in Figure 4.

B. Wire Barrel Crimp Profile and Location

The wire barrel crimp produced by the tooling (dies, heads, hand tools, pneumatic tools, or machines)

must be either a confined crescent crimp which appears as a depressed oval shape or a flat rectangular

crimp over the center of the wire barrel. The crimp must be evenly formed. Refer to Figures 4, 5, and 11.

Crescent crimp tooling produces the crescent crimp, and TETRA–CRIMP tooling produces the flat

rectangular crimp. For a tooling–to–crimp profile cross–reference, refer to Figure 10.

C. Dot Code

The dot code on the insulation must be well formed and correspond with the wire size or color code

marking on the crimping chamber of the tooling used. See Figures 4 and 5.

D. Bellmouths

There shall be no rear bellmouth. The front bellmouth shall be evident on the top and bottom of the wire

barrel as shown in Figure 5. Also see Figure 11.

Rev E

Tyco Electronics Corporation

5 of 14

Recommended Resources

Electric iron automatic temperature adjustment principle circuit diagram

instrumentation amplifier

The ever-changing sound and light analog controller circuit 06

Charger circuit diagram that automatically stops charging

Charger circuit diagram powered by switching power supply

555 drought-resistant automatic irrigation machine circuit

[2013 Young Teachers Summer Training Materials] LaunchPad Pocket Experiment Platform—MSP-EXP430G2.pptx: [size=6][color=#ff0000][b]Download address: This file is large, please download patiently [url]https://download.eeworld.com.cn/detail/qinkaiabc/283462[/url][/b][/color][/size]...; qinkaiabc Microcontroller MCU

Huaqing Vision Course Notes: Huaqing Yuanjian Embedded Course Second Lecture NotesThe second phase is the main course of their training. The quality is pretty good. Interested friends can download it and have a look. It's free!！:...; 115515296 ARM Technology

Fast charger for walkie-talkie: This article introduces a constant current fast charger suitable for walkie-talkies, which can charge 6 or 9 nickel-cadmium batteries. The charging time is 2 hours and the charger stops automatically ...; zoe Power technology

How to copy the files used in the compiler and IDE installation directory to the project folder when creating a new CCS project: When creating a new project in CCS, can I choose to copy the library files used in the CCS installation directory and the compiler installation directory used in this project to the project file? Some...; DX_E2 Microcontroller MCU

The room is very damp, do you have any good way to dehumidify it?: [i=s]This post was last edited by mmmllb on 2016-3-21 11:52[/i] The room I live in now is very damp and uncomfortable. It is said that a too humid environment is not good for the body. I wonder if any...; mmmllb Talking

Fast real-time communication via RTFL: Today, automation technology covers the entire spectrum: from fast real-time applications in the microsecond range to large distributed networks in hybrid topologies. The transmission of automation an...; mogecool RF/Wirelessly

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components