L: output is low level (weak pull down) oscillation stops
SiTime Corporation
Rev. 1.04
990 Almanor Avenue, Suite 200
Sunnyvale, CA 94085
(408) 328-4400
www.sitime.com
Revised Sept. 19, 2008
SiT8002
Description
The SiT8002 oscillator family is composed of the world’s
smallest, high-performance programmable oscillators. The
SiT8002 is suitable for use in clock generation for consumer,
portable, industrial, automotive, and computation applications.
This oscillator family is packaged in standard low-cost plastic
QFN-type IC packages with footprints that match common
quartz surface mount products.
MEMS resonators are 1000x smaller by volume than quartz
resonators and are built in high volume CMOS fabs instead of
small custom manufacturing facilities. Due to their small size,
massive lot sizes, and simpler manufacturing processes
MEMS oscillators are inherently more reliable, have more
consistent performance and are always in stock.
The SiT8002, by eliminating the quartz crystals, has improved
immunity to the environmental effects of vibration, shock,
strain, and humidity.
To order samples, go to www.sitime.com and click on Request
Sample” link.
Absolute Maximum Ratings
Attempted operation outside the absolute maximum ratings of the part may cause permanent damage to the part. Actual
performance of the IC is only guaranteed within the operational specifications not absolute maximum ratings.
Ab
solute Maximum Table
Parameter
Storage Temperature
VDD
Electrostatic Discharge
Theta JA ( with copper plane on VDD and GND)
Theta JC (with PCB traces of 0.010 inch to all pins)
Soldering Temperature (follow standard Pb free soldering guidelines)
Number of Program Writes
Program Retention over -40 to 125C, Process, VDD (0 to 3.6V)
–
–
Min.
-65
-0.5
Max.
150
+3.65
6000
75
24
260
1
1,000+
Unit
°C
V
V
°C/W
°C/W
°C
NA
years
Operating Conditions
Parameter
Supply Voltages, VDD
[1]
Min.
2.97
2.25
1.7
Typ.
3.3
2.5
1.8
-
-
-
-
Max.
3.63
2.75
1.9
70
85
15
200
Unit
V
V
V
°C
°C
pF
ms
Extended Commercial OperatingTemperature
Industrial Operating Temperature
Maximum Load
Capacitance
[2]
VDD Ramp Time
-20
-40
-
0
Environmental Compliance
Parameter
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Moisture Sensibility Level
Condition/Test Method
MIL-STD-883F, Method 2002
MIL-STD-883F, Method 2007
JESD22, Method A104
MIL-STD-883F, Method 2003
MSL1 @ 260°C
Notes:
1. The 2.5V device can operate from 2.25V to 3.63V with higher output drive, however, the data sheet parameters cannot be guaranteed. Please contact factory for
this option.
2. The output driver strenght can be programmed to drive up to 30pF load. Please contact factory for this option.
Page 2 of 7
SiT8002
DC Electrical Specifications
@VDD = 3.3V ±10%, -40 to 85°C
Parameter
Output Voltage High
Output Voltage Low
Input Voltage High
Input Voltage Low
Operating Current
Standby Current
Power Up Time
Condition
IOH = -9 mA
IOL = 9 mA
Pin 1
Pin 1
Output frequency = 65 MHz, 15 pF load
Output is weakly pulled down, ST = GND
Time from minimum power supply voltage
Min.
90
-
70
-
-
-
-
Typ.
-
-
-
-
-
30
12
Max.
-
10
-
30
22
50
50
Unit
%Vdd
%Vdd
%Vdd
%Vdd
mA
uA
ms
@VDD = 2.5V ±10%, -40 to 85°C
Parameter
Output Voltage High
Output Voltage Low
Input Voltage High
Input Voltage Low
Operating Current
Standby Current
Power Up Time
Condition
IOH = -7 mA
IOL = 7 mA
Pin 1
Pin 1
Output frequency = 65 MHz, 15 pF load
Output is weakly pulled down, ST = GND
Time from minimum power supply voltage
Min.
90
-
70
-
-
-
-
Typ.
-
-
-
-
-
30
12
Max.
-
10
-
30
22
50
50
Unit
%Vdd
%Vdd
%Vdd
%Vdd
mA
uA
ms
@VDD = 1.8V ±5%, -40 to 85°C
Parameter
Output Voltage High
Output Voltage Low
Input Voltage High
Input Voltage Low
Operating Current
Standby Current
Power Up Time
Condition
IOH = -5 mA
IOL = 5 mA
Pin 1
Pin 1
Output frequency = 65 MHz, 15 pF load
Output is weakly pulled down, ST = GND
Time from minimum power supply voltage
Min.
90
-
70
-
-
-
-
Typ.
-
-
-
-
-
30
12
Max.
-
10
-
30
19
50
50
Unit
%Vdd
%Vdd
%Vdd
%Vdd
mA
uA
ms
Page 3 of 7
SiT8002
AC Electrical Specifications
@VDD = 3.3V ±10%, -40 to 85°C
Parameter
Clock Output Frequency
Frequency
Tolerance
[3]
Inclusive of initial tolerance, operating temper-
ature, rated power supply voltage change, load
change,aging, shock and vibration
First year
Output frequency= 1 MHz to 125 MHz
15 pF Load, 20% to 80% VDD
15 pF Load, 80% to 20% VDD
Output frequency = 24 MHz
Output frequency = 100 MHz
Condition
Min.
1
-30
-50
-100
-
45
-
-
-
-
Typ.
-
-
-
-
-
-
1.0
1.0
-
-
Max.
125
+30
+50
+100
1
55
2.0
2.0
±98
±60
Unit
MHz
ppm
ppm
ppm
ppm
%
ns
ns
ps
ps
Aging
Clock Output Duty Cycle
Clock Output Rise Time
Clock Output Fall Time
Pk-pk Period Jitter
@VDD = 2.5V ±10%, -40 to 85°C
Parameter
Clock Output Frequency
Frequency Tolerance
[3]
Inclusive of initial tolerance, operating temper-
ature, rated power supply voltage change, load
change,aging, shock and vibration
First year
Output frequency= 1MHz to 125MHz
15 pF Load, 20% to 80% VDD
15 pF Load, 80% to 20% VDD
Output frequency = 24 MHz
Output frequency = 100 MHz
Condition
Min.
1
-30
-50
-100
-
45
-
-
-
-
Typ.
-
-
-
-
-
-
1.0
1.0
-
-
Max.
125
+30
+50
+100
1
55
2.0
2.0
±130
±60
Unit
MHz
ppm
ppm
ppm
ppm
%
ns
ns
ps
ps
Aging
Clock Output Duty Cycle
Clock Output Rise Time
Clock Output Fall Time
Pk-pk Period Jitter
@VDD = 1.8V ±5%, -40 to 85°C
Parameter
Clock Output Frequency
Frequency
Tolerance
[3]
Inclusive of initial tolerance, operating temper-
ature, rated power supply voltage change, load
change,aging, shock and vibration
First year
Output frequency= 1 MHz to 65MHz
Output frequency= 65 MHz to 125MHz
Clock Output Rise Time
Clock Output Fall Time
Pk-pk Period Jitter
15 pF Load, 20% to 80% VDD
15 pF Load, 80% to 20% VDD
Output frequency = 24 MHz
Output frequency = 100 MHz
Condition
Min.
1
-50
-100
-
45
40
-
-
-
-
Typ.
-
-
-
-
-
-
1.0
1.0
-
-
Max.
125
+50
+100
1
55
60
2.0
2.0
±185
±100
Unit
MHz
ppm
ppm
ppm
%
%
ns
ns
ps
ps
Aging
Clock Output Duty Cycle
Notes:
3. ±30 ppm is available only over extended commercial temperature range from-20 °C to +70 °C and VDD=2.5V or 3.3V.
I tested the air temperature and humidity and soil humidity and used LCD1602 to display it. But during the actual test, after using it for a period of time (it seemed to be an hour), the data on LCD16...
I have been engaged in the development of single-chip microcomputers for some years. Thanks to the continuous reduction in the cost of LCD, our products finally use color LCD. After a year of explorat...
How to design a high frequency power amplifier? And how to analyze such a circuit diagram? I would like to ask for your advice, including the specific calculation process, matching network, frequency ...
[align=center][size=5][color=#ff0000]Msp430 launchpad G2[font=宋体] series learning special topic[/font][/color][/size][/align][align=left][font=宋体][size=5] [/size][/font][/align][align=left][size=5][fo...
Due to the size limit of the video file upload, it will be demonstrated separately. First, the upright car is at a static tilt angle of 30 degrees and then powered on to stand in balance. [url]https:/...
Today, with the increasing integration of functions, mobile phones can also be used as portable media players (PMP), digital cameras, handheld computers (PDAs), and even global positioning systems ...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guang...[Details]
introduction
Throughout the history of automotive lighting, power has always played an important role. Initially, cars only needed headlights to see the road in the dark. Later, other light so...[Details]
There are three types of mobile TV: one is based on analog TV broadcasting network, another is based on mobile communication network, and the other is based on digital broadcasting network. The f...[Details]
When choosing a laptop battery, you should consider several factors, such as power, appearance, and quality.
Regarding power, we often see that a manufacturer uses values such as the number ...[Details]
introduction
The emergence of high-performance, low-power embedded CPUs and high-reliability network operating systems has made it possible to implement applications with large amounts of comp...[Details]
From the PIC16F946 datasheet, we know that there are two ways to write values to the LCD for display:
1. Directly write the value to LCDDATA1~LCDDATA23
2. Use disconnect t...[Details]
Editor's note: In order to help technicians or engineers who have knowledge of PIC microcontroller assembly language quickly master the method of using C language to program PIC microcontrollers, t...[Details]
Product series: PB-B-RS232/485 interface (hereinafter sometimes referred to as "interface") is a product in the PROFIBUS bus bridge series.
The main purpose of the bridge series ...[Details]
1 Introduction
Building Automation System (BAS) is a distributed monitoring system (DCS) designed according to distributed information and control theory. It is the result of the mutual de...[Details]
1 Introduction
With the development of control, computer, communication, network technology, etc., a new control technology, namely fieldbus, has emerged in the field of industrial control...[Details]
1 Introduction
Water resources are the basic conditions for human survival and the lifeline of economic development. The reality shows that due to the global shortage of water resources and th...[Details]
Nippon Electric Works and Volvo Technology Japan have developed a wireless power supply system for electric vehicles (EVs). Using this system, the two companies have successfully conducted an exper...[Details]
Toyohashi University of Technology demonstrated electric field coupled wireless power supply technology using life-size car tires and roads at the wireless technology exhibition "Wireless Technolog...[Details]
I've been studying dot matrix recently. It looks simple, but it takes a while to master it completely! The 8*8 dot matrix hardware circuit I'm making now is like this. The row is driven by 74HC138 + t...[Details]
Special Edition for Assessment Centres
京公网安备 11010802033920号
EEWORLD
