Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names.
Note: With nominal input/output voltage, maximum output current, and Ta=25° if not specified separately.
C,
Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout.
Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open.
(*1) With nominal input voltage, maximum output current, and Ta=25°
C.
(*2) The maximum output power value is between -40° and +50° For use in outside this temperature range, derating is needed.
C
C.
(*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal).
(*4) Output voltage includes input change, load change (balanced load), and temperature change.
(*5) In 50MHz, Ta=25°
C.
(*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30
seconds.
MODEL CC1R5-1203Sx-E CC1R5-1205Sx-E
CC1R5-1212Sx-E
CC1R5-1212Dx-E
ITEMS/UNITS
Nominal Voltage
V
DC12
Voltage Range
V
DC9.0-18
Input
Efficiency (typ)
(*1)
％
73
78
82
81
Current (typ)
(*1) A
0.151
0.160
0.152
0.154
Nominal Voltage
VDC
3.3
5
12
15
12
15
Maximum Current
A
0.400
0.300
0.125
0.100
0.060
0.050
Maximum Power
(*2) W
1.32
1.5
Maximum Line Regulation (Within input voltage range) mV
20
40
80
Maximum Load Regulation (0-100% load) (*3) mV
40
100
600
Output
Temperature Coefficient
80mV
200mV
300mV
(Ambient temperature–40° to +50°
C
C)
Max Power Total Regulation (max) (*4)
％
3
±
5
Maximum Ripple & Noise (typ/max) (*5) mVp-p
40/120
30/120
VDC
3.15-3.6
4.75-6.0
11.4-15.0
11.4 - 15.0
Voltage Adjustable Range
Over Current Protection
(*6)
Available
Function Over Voltage Protection
Not available
Remote ON/OFF Control
Available
Operating Ambient Temperature
℃
-40 to +85
Storage Ambient Temperature
℃
-40 to +85
％
RH
5-95 (the conditions of maximum 38° in wet bulb temperature and non-condensation should be ensured.)
C
Operating Ambient Humidity
Environment
Storage Ambient Humidity
％
RH
5-95 (the conditions of maximum 38° in wet bulb temperature and non-condensation should be ensured.)
C
Vibration
10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each
Shock
980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation
Withstand Voltage
Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute)
Isolation
Isolation Resistance
Between input terminal and output terminal: 500VDC, 50MΩ min
Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names.
Note: With nominal input/output voltage, maximum output current, and Ta=25° if not specified separately.
C,
Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout.
Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open.
(*1) With nominal input voltage, maximum output current, and Ta=25°
C.
(*2) The maximum output power value is between -40° and +50° For use in outside this temperature range, derating is needed.
C
C.
(*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal).
(*4) Output voltage includes input change, load change (balanced load), and temperature change.
(*5) In 50MHz, Ta=25°
C.
(*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30
seconds.
・All specifications are subject to change without notice.
2
CC1R5-E
3
MODEL CC1R5-2403Sx-E CC1R5-2405Sx-E
CC1R5-2412Sx-E
CC1R5-2412Dx-E
ITEMS/UNITS
Nominal Voltage
V
DC24
Voltage Range
V
DC18-36
Input
Efficiency (typ)
(*1)
％
72
77
81
79
Current (typ)
(*1) A
0.076
0.081
0.077
0.079
Nominal Voltage
VDC
3.3
5
12
15
12
15
Maximum Current
A
0.400
0.300
0.125
0.100
0.060
0.050
Maximum Power
(*2) W
1.32
1.5
Maximum Line Regulation (Within input voltage range) mV
20
40
80
Maximum Load Regulation (0-100% load) (*3) mV
40
100
600
Output
Temperature Coefficient
80mV
200mV
300mV
(Ambient temperature–40° to +50°
C
C)
Max Power Total Regulation (max) (*4)
％
3
5
Maximum Ripple & Noise (typ/max) (*5) mVp-p
40/120
30/120
VDC
3.15-3.6
4.75-6.0
11.4-15.0
11.4- 15.0
Voltage Adjustable Range
Over Current Protection
(*6)
Available
Not available
Function Over Voltage Protection
Remote ON/OFF Control
Available
Operating Ambient Temperature
℃
-40 to +85
Storage Ambient Temperature
℃
-40 to +85
Operating Ambient Humidity
％
RH
5-95 (the conditions of maximum 38° in wet bulb temperature and non-condensation should be ensured.)
C
Environment
Storage Ambient Humidity
％
RH
5-95 (the conditions of maximum 38° in wet bulb temperature and non-condensation should be ensured.)
C
Vibration
10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each
Shock
980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation
Withstand Voltage
Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute)
Isolation
Isolation Resistance
Between input terminal and output terminal: 500VDC, 50MΩ min
Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names.
Note: With nominal input/output voltage, maximum output current, and Ta=25° if not specified separately.
C,
Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout.
Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open.
(*1) With nominal input voltage, maximum output current, and Ta=25°
C.
(*2) The maximum output power value is between -40° and +50° For use in outside this temperature range, derating is needed.
C
C.
(*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal).
(*4) Output voltage includes input change, load change (balanced load), and temperature change.
(*5) In 50MHz, Ta=25°
C.
(*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30
seconds.
MODEL CC1R5-4803Sx-E CC1R5-4805Sx-E
CC1R5-4812Sx-E
CC1R5-4812Dx-E
ITEMS/UNITS
Nominal Voltage
V
DC48
Voltage Range
V
DC36-76
Input
Efficiency (typ)
(*1)
％
70
76
80
79
Current (typ)
(*1) A
0.039
0.041
0.039
0.040
Nominal Voltage
VDC
3.3
5
12
15
12
15
Maximum Current
A
0.400
0.300
0.125
0.100
0.060
0.050
Maximum Power
(*2) W
1.32
1.5
Maximum Line Regulation (Within input voltage range) mV
20
40
80
Maximum Load Regulation (0-100% load) (*3) mV
40
100
600
Output
Temperature Coefficient
80mV
200mV
300mV
(Ambient temperature–40° to +50°
C
C)
Max Power Total Regulation (max) (*4)
％
3
5
Maximum Ripple & Noise (typ/max) (*5) mVp-p
40/120
30/120
VDC
3.15-3.6
4.75-6.0
11.4-15.0
11.4- 15.0
Voltage Adjustable Range
Over Current Protection
(*6)
Available
Not available
Function Over Voltage Protection
Remote ON/OFF Control
Available
℃
-40 to +85
Operating Ambient Temperature
℃
-40 to +85
Storage Ambient Temperature
％
RH
5-95 (the conditions of maximum 38° in wet bulb temperature and non-condensation should be ensured.)
C
Operating Ambient Humidity
Environment
％
RH
5-95 (the conditions of maximum 38° in wet bulb temperature and non-condensation should be ensured.)
C
Storage Ambient Humidity
Vibration
10-55Hz, 15 minutes sweep and 1.52mm total amplitude, 3 directions, 2h for each
Shock
980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation
Withstand Voltage
Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute)
Isolation
Between input terminal and output terminal: 500VDC, 50MΩ min
Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names.
Note: With nominal input/output voltage, maximum output current, and Ta=25° if not specified separately.
C,
Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout.
Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open.
(*1) With nominal input voltage, maximum output current, and Ta=25°
C.
(*2) The maximum output power value is between -40° and +50° For use in outside this temperature range, derating is needed.
C
C.
(*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal).
(*4) Output voltage includes input change, load change (balanced load), and temperature change.
(*5) In 50MHz, Ta=25°
C.
(*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30
seconds.
・All specifications are subject to change without notice.
CC1R5-E
Outline Drawing
CC1R5-xxxxxF-E (DIP type)
Shape/Dimensions
8.5max.
4
16.6±0.2
Recommended measurements for
mounting board
4.0
14.605
2.92
Outer shape of
product
16.51
2.54
(3.22)
0.5
1.905
a
3
2
7.62
12.7
1.905
b
4
5
a
2.7
13.08
12.7
7-ø1.0 (land diameter ø2.0)
2-ø1.5 (land diameter ø2.5)
3.5
2.54 5.08 2.54
16.51
1.0
b
0.5
7-0.3×0.6
1
b
6
7
a
2.7
CC1R5-xxxxxR-E (SMD type)
Shape/Dimensions
8.8max.
(3.22)
Unit: mm
Allowable tolerance is ±0.5 if not specified separately.
16.6±0.2
Recommended measurements for
mounting board
4.0
(3.22)
Outer shape of
product
2.54 5.08 2.54
3.2
3.5
t=0.3
10.16
7.62
t=0.3
(13.38)
16.51
Coplanarity: 0.1 or lower
1.8
19.81
1.8
2.54
(3.22)
3.2
15.6
22.0
2
7.62
5
7-0.3×0.6
6
7
(3.22)
1
2.54 5.08 2.54
3
4
Unit: mm
Allowable tolerance is ±0.5 if not specified separately.
Connection diagram
CC1R5-xxxxSx-E
+Vin
1
7
6
RC
–Vin
5
2
3
+Vout
Terminal connections
No.1
No.2
No.3
No.4
No.5
No.6
No.7
+Vin
RC
–Vin
NC
–Vout
TRM
+Vout
Load
CC1R5-xxxxDx-E
+Vin
1
7
6
RC
–Vin
5
2
3
4
+Vout
Terminal connections
No.1
No.2
No.3
No.4
No.5
No.6
No.7
+Vin
RC
–Vin
–Vout
Common out
TRM
+Vout
Load
TRM
–Vout
TRM
COM
–Vout
4 NC
Derating Curve
100
Output power (%)
80
60
40
20
Natural air cooling
a
b
a:
0.5m/s
(100LFM)
b:
1m/s
(200LFM)
Ambient temperature (°
C)
0
-40 -20 0 20 40 60 80 100
Output power derating by ambient temperature
(common specification)
・All specifications are subject to change without notice.
2.54 5.08 2.54
10.16
7.62
1.2
Load
（DIP/SMD）
CC3-E
CC3-E Specifications
MODEL CC3-0503Sx-E
CC3-0505Sx-E
CC3-0512Sx-E
CC3-0512Dx-E
ITEMS/UNITS
Nominal Voltage
V
DC5.0
Voltage Range
V
DC4.5-9.0
Input
Efficiency (typ)
(*1)
％
73
77
82
81
Current (typ)
(*1) A
0.723
0.779
0.732
0.741
VDC
3.3
5
12
15
12
15
Nominal Voltage
Maximum Current
A
0.800
0.600
0.250
0.200
0.125
0.100
Maximum Power
(*2)
2.64
3
Maximum Line Regulation(Within input voltage range) mV
20
40
80
Maximum Load Regulation (0-100% load) (*3) mV
40
100
600
Output
Temperature Coefficient
80mV
200mV
300mV
(Ambient temperature -40℃ to +50℃ )
Max Power Total Regulation (max) (*4)
％
3
5
Maximum Ripple & Noise (typ/max) (*5) mVp-p
40/120
30/120
Voltage Adjustable Range
VDC
3.15-3.6
4.75-6.0
11.4-15.0
11.4- 15.0
Over Current Protection
(*6)
Available
Function Over Voltage Protection
Not available
Remote ON/OFF Control
Available
Operating Ambient Temperature
℃
-40 to +85
Storage Ambient Temperature
℃
-40 to +85
Operating Ambient Humidity
％
RH
5-95 (the conditions of maximum 38℃ in wet bulb temperature and non-condensation should be ensured.)
Environment
Storage Ambient Humidity
％
RH
5-95 (the conditions of maximum 38℃ in wet bulb temperature and non-condensation should be ensured.)
10-55Hz, 15 minutes sweep and 1.52mm total amplitude, X/Y/Z 3 directions, 2h for each
Vibration
Shock
980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation
Withstand Voltage
Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute)
Isolation
Isolation Resistance
Between input terminal and output terminal: 500VDC, 50MΩ min
Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names.
Note: With nominal input/output voltage, maximum output current, and Ta=25° if not specified separately.
C,
Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout.
Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open.
(*1) With nominal input voltage, maximum output current, and Ta=25°
C.
(*2) The maximum output power value is between -40° and +50° For use in outside this temperature range, derating is needed.
C
C.
(*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal).
(*4) Output voltage includes input change, load change (balanced load), and temperature change.
(*5) In 50MHz, Ta=25°
C.
(*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30
seconds.
MODEL CC3-1203Sx-E
CC3-1205Sx-E
CC3-1212Sx-E
CC3-1212Dx-E
ITEMS/UNITS
Nominal Voltage
V
DC12
Voltage Range
V
DC9.0-18
Input
Efficiency (typ)
(*1)
％
74
79
82
81
Current (typ)
(*1) A
0.297
0.316
0.305
0.309
Nominal Voltage
VDC
3.3
5
12
15
12
15
Maximum Current
A
0.800
0.600
0.250
0.200
0.125
0.100
Maximum Power
(*2) W
2.64
3
Maximum Line Regulation(Within input voltage range) mV
20
40
80
Maximum Load Regulation (0-100% load) (*3) mV
40
100
600
Output
Temperature Coefficient
80mV
200mV
300mV
(Ambient temperature -40℃ to +50℃ )
Max Power Total Regulation (max) (*4)
％
3
5
Maximum Ripple & Noise (typ/max) (*5) mVp-p
40/120
30/120
VDC
3.15-3.6
4.75-6.0
11.4-15.0
11.4- 15.0
Voltage Adjustable Range
Over Current Protection
(*6)
Available
Not available
Function Over Voltage Protection
Remote ON/OFF Control
Available
℃
-40 to +85
Operating Ambient Temperature
℃
-40 to +85
Storage Ambient Temperature
％
RH
5-95 (the conditions of maximum 38° in wet bulb temperature and non-condensation should be ensured.)
C
Operating Ambient Humidity
Environment
％
RH
5-95 (the conditions of maximum 38° in wet bulb temperature and non-condensation should be ensured.)
C
Storage Ambient Humidity
Vibration
10-55Hz, 15 minutes sweep and 1.52mm total amplitude, X/Y/Z 3 directions, 2h for each
Shock
980m/s² (100G), 6ms, 6 directions, 3 times for each, in non-operation
Withstand Voltage
Between input terminal and case, between input terminal and output terminal, and between output terminal and case: 500VAC (for 1 minute)
Isolation
Isolation Resistance
Between input terminal and output terminal: 500VDC, 50MΩ min
Note: "x" in model names is to be replaced by a symbol which represents the terminal configuration (F: DIP/R: SMD) for actual model names.
Note: With nominal input/output voltage, maximum output current, and Ta=25° if not specified separately.
C,
Note: For 12V/±12V models, output voltage can be set to 15V/±15V by connecting the output adjustment terminal TRM to -Vout.
Note: For 12V model, output voltage can be set to 24V or 30V single output by making the COM terminal open.
(*1) With nominal input voltage, maximum output current, and Ta=25°
C.
(*2) The maximum output power value is between -40° and +50° For use in outside this temperature range, derating is needed.
C
C.
(*3) In balanced load for dual outputs ( "balanced load" means a condition where the +output and -output of load current are equal).
(*4) Output voltage includes input change, load change (balanced load), and temperature change.
(*5) In 50MHz, Ta=25°
C.
(*6) Output current restriction method. Automatically resumes when the causes are removed. Never operate the unit under output-shorted or overload conditions for over 30
seconds.
・All specifications are subject to change without notice.
I don't know how you solder this kind of chip. When I soldered LQFP chips in the past, I first fixed one or two pins on the PCB, and then used an electric soldering iron with tin wire to solder the ot...
[i=s]This post was last edited by dontium on 2014-5-13 16:38[/i] I found this thing from a friend a long time ago, and I got it after he invited me to the party. I used this thing to write an article ...
I am a beginner and don't have a development board yet. I want to learn DSP2812 through software simulation first. I want to find some simple pure software simulation examples suitable for beginners. ...
[color=#000][font=Arial,] [/font][/color][font=Arial, Microsoft YaHei, 微软雅黑, SimSun, 宋体, sans-serif][color=#000000][size=15px] The turn signal lights on cars are no longer limited to flashing on and o...
Overview
Lightning is a strong discharge phenomenon that occurs between thunderstorm clouds and between thunderstorm clouds and the earth due to severe convective weather. Lightning is gen...[Details]
From last year to now, competition in the photovoltaic inverter industry has become increasingly fierce. In addition to the introduction of new products, various marketing and promotion methods hav...[Details]
Recently, Zhejiang Lipu Crushing Equipment Co., Ltd. invested 50 million yuan to build a new "annual production of 1,200 high-efficiency and energy-saving ultra-fine pulverizer construction project...[Details]
International Solar Photovoltaic Network News: On November 21, Australia's SMA Solar Technology Co., Ltd. signed a contract with the local government to provide photovoltaic inverters with an insta...[Details]
Q1: What information do I need to provide when reporting inverter issues?
A: Machine serial number, fault picture, on-site measurement picture, component information, etc.
Q2: What should...[Details]
In summer, the shell temperature of the inverter is relatively high and it feels hot to the touch. So is it better for the inverter shell to be hot or not? And why does the shell feel hot? The foll...[Details]
After the PV system is installed, the user is most concerned about the power generation, because it is directly related to the user's return on investment. There are many factors that affect the po...[Details]
2017 is considered by many photovoltaic people to be the first year of distributed photovoltaic development. In the first half of 2017 alone, the newly installed capacity of distributed photovoltaic w...[Details]
The year 2017 has become history in the blink of an eye. Looking back at the past year, China's household photovoltaics have shown explosive development in the motherland, which can be called the f...[Details]
Introduction:
At present, the power generation efficiency (PR value) of photovoltaic systems is generally around 80%, and the power generation efficiency of photovoltaic systems can direct...[Details]
Recently, the Ministry of Industry and Information Technology, the Ministry of Science and Technology, the Ministry of Environmental Protection, the Ministry of Transport, the Ministry of Commerce,...[Details]
ABB (VTX:ABBN) will provide a 24.5 MW microgrid facility and energy storage system to help integrate solar and wind power into Jamaica’s electricity supply.
Microgrids will support...[Details]
China Energy Storage Network News:
—— Interview with Executive Vice President of Tsinghua University Energy Internet Innovation Institute
Reporter: In your opinion, what will the...[Details]
China Energy Storage Network News:
On November 15, the 2016 China Electrical Engineering Society Annual Conference with the theme of "Innovation-driven and Power Transformation Development" w...[Details]
Founded in 1986, Tianneng Group celebrates its 30th birthday. At the age of 30, how can it transform and upgrade under the new normal and achieve green growth and sustainable development? Tianneng ...[Details]
PCB Design
京公网安备 11010802033920号
EEWORLD
