1485EZC12 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Topical application> Mechanical and electrical/engineering/automation> 1485EZC12

1485EZC12: CategoryTopical application Mechanical and electrical/engineering/automation; File Size191KB，3 Pages; ManufacturerHammond; Websitehttp://www.hammondmfg.com

Download Datasheet Parametric View All

1485EZC12 Online Shopping

Suppliers	Part Number	Price	MOQ	In stock
	1485EZC12	-	-	View	Buy Now

1485EZC12 Parametric

Parameter Name	Attribute value
Product Category	Racks & Rack Cabinet Accessories
Manufacturer	Hammond
RoHS	Details
Factory Pack Quantity	1
Unit Weight	16 lbs

Preview

Download Datasheet

View All

11/25/2017

Type 12 Lay-In Wireway (1485 Series) - Hammond Mfg.

Quality Products. Service Excellence.

Type 12 Lay-In Wireway

1485 Series

Wireway & Accessories

Application

Designed to enclose and protect electrical wiring from dirt, dust, oil and water.

All sections and fittings are completely open on each side to allow wires and cables to be

placed into the wireway without "pulling through".

Standards

UL 870 Type 1 (unless marked1)

CSA Type 1 (unless marked1)

Complies with

NEMA Type 12

JIC EMP-1-1967

JIC EGP-1-1967

IEC 60529, IP54

Construction

Bodies and covers are formed from 14-gauge steel with 10 gauge steel flanges.

12” x 6” size has a 12 gauge steel body with a 14-gauge cover.

Smooth continuously welded seams.

Interior surfaces are smooth to prevent wire damage during

installation.

Butt hinged cover is secured with easily operated quick release clamps.

Oil resistant gaskets are permanently secured.

Solid oil resistant gaskets are used between flanges when sections and fittings are bolted

together.

One gasket kit, complete with hardware is provided with each straight section or fitting.

Sealing plate is supplied.

Flange junctions are sealed with gasket sealing plates, which are put in place after wiring

is completed. One is supplied with all straight sections and most fittings; see table for

exact number.

Finish

Sections and components are finished in ANSI 61 gray powder coating.

Notes

When joining a wireway section or fitting to an enclosure be sure to order a box

connector.

When joining two wireway sections, or joining a wireway section to a fitting, a flat sealing

plate is required at each junction; necessary kits are supplied with each section and

fitting. See table, extra kits may be ordered if necessary.

When joining a lay-in wireway section or fitting to a closure plate, a box connector, or cut-

off fitting, an angle sealing plate is required at each junction.

Necessary kits are supplied with each section and fitting - see table. Extra kits, although

not normally required, are necessary when joining lay-in wireway to a non-lay-in section

https://www.hammfg.com/electrical/products/wireway/1485

1/3

Recommended Resources

USART circuit design based on RS232 asynchronous serial communication

175MHz high frequency power amplifier circuit composed of field effect transistors

Precision regulated power supply circuit for UJ-1 type potentiometer

LT3755 driver LED application circuit diagram

Binary number square root circuit

LA4500 power amplifier circuit

Problems with serial programming of STC89C51RC microcontroller: The program download design of the 51 single-chip microcomputer hardware design is shown in the figure, but the program cannot be burned in, the single-chip microcomputer cannot be detected, and the v...; Simonbinbin 51mcu

Is your source measurement unit suitable for automated testing?: [align=left]Source measure units (SMUs) are the primary instruments used to analyze device current-voltage (IV) characteristics in laboratory characterization and automated test applications. PXI SMUs...; 橙色凯 Test/Measurement

【ST NUCLEO-H743ZI Review】+ 2. LED Flowing Light: Through the previous learning, I have an understanding of the environment construction, and I can create my own project files through the routine learning. Here I will light up the LED water lamp to f...; TL-LED stm32/stm8

The difference between ESN and IMEI number of mobile phone: When I read the IMEI number recently, I found that the IMEI number I read out is the same as the ESN number of the mobile phone. Why is this? And the IMEI number obtained by entering "*#06#" in the mo...; victor556 Embedded System

Magnetic Field Test Antenna: ...; led123 Test/Measurement

AX88976 network interface circuit diagram: AX88976 network interface circuit diagram...; klanlan Industrial Control Electronics

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components