When developing a program, we often hope that some global variables have the desired initial values when they are used. We usually use the following two methods to implement the initial value assignme...
I lost my Ruitai Innovation ICETEK-F2812-A development board. I'm willing to pay you for it. Good or bad, even a bare board is fine. Please contact me on QQ: 1332430115. Please indicate this when you ...
[table=95%][tr][td]I read a book and thought that the timer could theoretically produce a frequency of 1MHz, but in reality it only produced a frequency of more than 30K. I used a 12MHz crystal oscill...
[i=s] This post was last edited by eeacc on 2014-6-14 09:53 [/i] In complementary output mode, how can I turn off the B phase output and make it high? I set the A phase high EPwm1Regs.AQCSFRC.bit.CSFA...
[b]1-4-3. Calculation of energy storage inductance of parallel switching power supply[/b] The calculation method of energy storage inductance in the reverse series switching power supply is basically ...
Activity details: Win big prizes by passing the VISHAY Industrial Power Theme Month! Activity link: [url=https://www.eeworld.com.cn/Vishay/2012_activity/Industrial/]https://www.eeworld.com.cn/Vishay/2...
UHF and HF are both general technology categories, but each category has independent supporting protocols. HF is more consistent in the 13.56MHz frequency band, although there are many internation...[Details]
Medical and industrial applications often require isolation voltages of 2500Vac or higher for patient and equipment operator safety. The isolation barrier must not only transmit power to the sensin...[Details]
Conventional ECG recorders are one of the main means for doctors to diagnose heart diseases, but they can only record short heartbeats. In many cases, it is difficult to record ECG changes during a...[Details]
In the future, a complete automobile safety system must fully combine gyroscopes, accelerometers, steering wheel and brake pedal position detectors, and tire speed detection systems to accurately ...[Details]
In a Class D audio power amplifier, the preamplifier is a relatively important module. It is located at the front of the entire topology and completes the processing of the input signal source,...[Details]
Power semiconductors and reactive components (capacitors and inductors) are ubiquitous in today's electrical equipment. In normal operation, they can cause two undesirable side effects on the AC line ...[Details]
Most
embedded
systems are powered from a 48V backplane. This voltage is typically stepped down to a lower intermediate bus voltage of 24V, 12V, or 5V to power the circuit board racks withi...[Details]
Multiple Input and Multiple Output (MIMO) technology is arguably the next most important development in wireless communication technology since the advent of digital communications. Many new wir...[Details]
Abstract: This paper introduces the controller, interface, display principle and driving method of the handheld computer LCD display based on the SA1110 microprocessor. Combined with the HPC projec...[Details]
CVC5.0 (CSR recently announced the fifth generation of clear voice capture technology) is the only solution on the market that provides advanced audio enhancement and noise suppression to both the ...[Details]
1 Introduction
Digital video is the use of video capture devices such as cameras to collect external image information and digitize the image information, and then record it to storage med...[Details]
Today, the value of electronic components in cars accounts for 15-20% of the total vehicle. In the future, as more safety electronic devices, fuel consumption and fuel emission control electronic s...[Details]
With the popularity of 3G network, some new laptops have built-in 3G wireless network cards, namely G3 laptops. For most users of relatively old computers, if they have a 3G wireless network card, ...[Details]
With the development of LED technology, the application of LED has expanded from the traditional low-power portable product backlight to medium- and high-power indoor lighting, outdoor lighting, an...[Details]
Analysis of automotive sensor testing requirements
At present, the control system used in automobiles can be functionally divided into three parts: sensor unit, control unit and execution ...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
